Synthesis and slurry spray coating of barium strontium alumino silicate on SiC substrate

Barium strontium alumino silicate (BSAS); (Ba_0.6Sr_0.4Al₂Si₂O₈) was synthesized through solid state reaction between BaCO₃, SrCO₃, Al₂O₃ and SiO₂ subjected to wet milling in isopropanol for about 24 h. The sequence of the solid state reaction was studied by subjecting to DG/DTG from room temperature to 1550 °C. The crystallographic phase evolution was confirmed by X-ray diffraction of the powders calcined in the range 1000 to 1300 °C for 2 h. The monoclinic celsian phase obtained at 1300 °C, pelletized through uniaxial pressing was sinterable to 67 to 78% density in the temperature range of 1300 to 1500 °C. The density improved to 75 to 94% after ball milling for 76 h, while ZrO₂ addition further improved the density by 2%. The celcian phase of BSAS was dispersed in isopropyl alcohol, milled for about 24 h and spray coated on to plain SiC and mullite precoated SiC substrates. Sintering of coated samples and characterization for weight gain/loss, microstructure, scratch test prove that mullite + BSAS coating is more effective than single layer coating of BSAS on SiC substrates.     

High performance H2 sensor based on rGO-wrapped SnO2–Pd porous hollow spheres

Hydrogen (H₂) sensors based on metal oxide semiconductors (MOS) are promising for many applications such as a rocket propellant, industrial gas and the safety of storage. However, poor selectivity at low analyte concentrations, and independent response on high humidity limit the practical applications. Herein, we designed rGO-wrapped SnO₂–Pd porous hollow spheres composite (SnO₂–Pd@rGO) for high performance H₂ sensor. The porous hollow structure was from the carbon sphere template. The rGO wrapping was via self-assembly of GO on SnO₂-based spheres with subsequent thermal reduction in H₂ ambient. This sensor exhibited excellently selective H₂ sensing performances at 390 °C, linear response over a broad concentration range (0.1–1000 ppm) with recovery time of only 3 s, a high response of ～8 to 0.1 ppm H₂ in a minute, and acceptable stability under high humidity conditions (e. g. 80%). The calculated detection limit of 16.5 ppb opened up the possibility of trace H₂ monitoring. Furthermore, this sensor demonstrated certain response to H₂ at the minimum concentration of 50 ppm at 130 °C. These performances mainly benefited from the special hollow porous structure with abundant heterojunctions, the catalysis of the doped-PdO_x, the relative hydrophobic surface from rGO, and the deoxygenation after H₂ reduction.     

钻井机器人的连续油管钻压和钻速控制模型

连续油管钻井机器人利用机身内外的钻井液压力差作为动力源，可在牵引连续油管的同时加载钻压。以钻井机器人为基础，建立连续油管钻柱动力学模型，并推导出通过钻井液排量控制钻压和钻速的单参数控制数学模型；对钻井机器人引入调速回路，建立具有调速功能的钻柱动力学模型；在溢流阀调定压力大于机身内外压差时，推导出利用钻井液排量和节流阀流通面积两种参数控制钻压、钻速的数学模型，在溢流阀调定压力小于机身内外压差时，推导出利用钻井液排量、节流阀流通面积和溢流阀调定压力3种参数控制钻压、钻速的数学模型；以11.43 cm（4.5英寸）井眼为例，对上述3种数学模型进行了分析。分析结果表明：钻压、钻速随钻井液排量的增加基本呈线性增加，在钻井液排量大于0.005 m³/s时，钻井机器人能够向前爬行，在钻井液排量大于0.005 7 m³/s时，钻头能够正常钻进；调节节流阀流通面积和溢流阀调定压力，可以在一定范围内无级调钻压和钻速；3种控制方法相结合，可以实现小排量、大钻压，及大排量、小钻压等钻井参数的控制。以控制模型为基础，针对不同井下工况建立钻进工艺的专家数据库，以钻井机器人为"大脑"，结合井下随钻测量数据就能够实现闭环控制，自动钻进。     

Compiler compatible 5.66 Mb/mm2 8T 1R1W register file in 14 nm FinFET technology

1-read/1-write (1R1W) register file (RF) is a popular memory configuration in modern feature rich SoCs requiring significant amount of embedded memory. A memory compiler is constructed using the 8T RF bitcell spanning a range of instances from 32 b to 72 Kb. An 8T low-leakage bitcell of 0.106 μm² is used in a 14 nm FinFET technology with a 70 nm contacted gate pitch for high-density (HD) two-port (TP) RF memory compiler which achieves 5.66 Mb/mm² array density for a 72 Kb array which is the highest reported density in 14 nm FinFET technology. The density improvement is achieved by using techniques such as leaf-cell optimization (eliminating transistors), better architectural planning, top level connectivity through leaf-cell abutment and minimizing the number of unique leaf-cells. These techniques are fully compatible with memory compiler usage over the required span. Leakage power is minimized by using power-switches without degrading the density mentioned above. Self-induced supply voltage collapse technique is applied for write and a four stack static keeper is used for read Vmin improvement. Fabricated test chips using 14 nm process have demonstrated 2.33 GHz performance at 1.1 V/25 °C operation. Overall V_min of 550 mV is achieved with this design at 25 °C. The inbuilt power-switch improves leakage power by 12x in simulation. Approximately 8% die area of a leading 14 nm SoC in commercialization is occupied by these compiled RF instances.     

基于深度语义分割的多源遥感图像海面溢油监测

针对遥感图像海面溢油区域通常受到斑噪声以及强度不均等因素的影响,从而导致溢油区域监测效果较差的问题,本文引入了深度语义分割的方法,将深度卷积神经网络与全连接条件随机场相结合,形成端对端连接。以Resnet结构为基础,首先通过深度卷积神经网络对多源遥感图像粗分割并作为输入,然后经过改进的全连接条件随机场,利用高斯成对势和平均场近似定理,建立条件随机场形成递归神经网络作为输出。通过多源遥感图像对海面溢油区域进行监测,并利用可见光图像估计溢油区域面积。实验在所建立的多源遥感图像数据集上与其它先进模型进行对比,结果表明本文方法提高了溢油区域的分割精度以及精细细节程度,平均交并比为82.1%,监测效果具有明显地改善。     

Comparison of OWAS,RULA and REBA for assessing potential work-related musculoskeletal disorders

This study compared three representative observational methods for assessing musculoskeletal loadings: Ovako Working Posture Analysis System (OWAS), Rapid Upper Limb Assessment (RULA), and Rapid Entire Body Assessment (REBA). The comparison was based on 209 cases of upper-body musculoskeletal disorders (MSDs) diagnosed by medical doctors. The most awkward/stressful posture in each participant's tasks was assessed using these techniques. Postural loadings were rated more highly by the RULA than by the OWAS and REBA (p < 0.01). The chi-square test and logistic regression analysis showed that only RULA grand score and action level, and REBA action level were associated with MSD work-relatedness (p < 0.01, p < 0.05, and p < 0.05, respectively). The percentage concordant values of the logistic model for the RULA grand score and action level were 52.4% and 44.8%, respectively, while the percentage concordant value for the REBA action level was 22.1%. Therefore, the RULA may be the best system for estimating the postural loads and work-relatedness of MSDs.Relevance to industryWork-related musculoskeletal disorders are the leading cause of workplace disability in the developed countries. For preventing the disorders, quantification of musculoskeletal loads is required.     

Operational scheduling of responsive prosumer farms for day‐ahead peak shaving by agricultural demand response aggregators

This paper proposes a novel structure to optimize the operational strategies of responsive farms for day‐ahead peak shaving. To achieve the aim, the modern irrigation system of farms, including groundwater, surface water, and booster water pumps, are modeled mathematically. To develop the demand response (DR) potentials of the farms, electrical storage systems, and self‐generation facilities, including thermal distributed generations and on‐farm solar sites, are addressed. In order to facilitate the integration of the agricultural DR programs into the electricity market, a mathematical formulation for agricultural demand response aggregator (ADRA) is suggested. The ADRA participates in the day‐ahead electricity market on behalf of the responsive farms. To overcome the price uncertainty of the electricity market, a robust optimization approach is addressed. This approach determines the robust decisions of farms in the worst‐case realizations of the uncertain electricity price. Regarding on‐farm solar sites located in rural areas, a data‐driven approach is used to estimate the solar power generation of a significant number of sites without needing to install costly communication and measurement infrastructures. Finally, the proposed approach is implemented on agricultural lands in the northeast of Iran. The numerical results show that the suggested approach provides day‐ahead peak shaving for the power systems meeting the crop's water requirements.     

基于文本与语义相关性分析的图像检索

为了更加有效地检索到符合用户复杂语义需求的图像，提出一种基于文本描述与语义相关性分析的图像检索算法。该方法将图像检索分为两步：基于文本语义相关性分析的图像检索和基于SIFT特征的相似图像扩展检索。根据自然语言处理技术分析得到用户文本需求中的关键词及其语义关联，在选定图像库中通过语义相关性分析得到“种子”图像；接下来在图像扩展检索中，采用基于SIFT特征的相似图像检索，利用之前得到的“种子”图像作为查询条件，在网络图像库中进行扩展检索，并在结果集上根据两次检索的图像相似度进行排序输出，最终得到更加丰富有效的图像检索结果。为了证明算法的有效性，在标准数据集Corel5K和网络数据集Deriantart8K上完成了多组实验，实验结果证明该方法能够得到较为精确地符合用户语义要求的图像检索结果，并且通过扩展算法可以得到更加丰富的检索结果。     

磁环表面缺陷图像分割算法的研究及实时实现

为实现小型磁环表面细微缺陷图像无监督分割,并提高分割精度与计算效率,本文提出了一种基于改进2D Gabor滤波器组的自适应阈值分割方法。首先,利用多尺度、多方向的Gabor滤波器组对缺陷图像进行滤波降噪处理,抑制目标区域与背景区域内部的噪声污染,同时增强区域间的差异性；然后,通过对处理后图像的灰度统计特性分析,根据缺陷图像的灰度均值及方差构造了灰度阈值计算公式,实现了小型磁环表面细微缺陷图像的自适应分割。实验结果表明,本文算法可快速、准确地分割缺陷并抑制噪声干扰,在分割精度、计算效率等方面也优于传统的选择迭代法、OTSU、最大熵等方法,并能够在先进的SEED-DVS8168平台上实时实现,验证了此算法的可行性与实时性。