Molecular weight studies of the γ‐irradiation degradation of poly(methyl methacrylate) doped with poly(p‐sulfanilamide)

The protection of some poly(methyl methacrylate) (PMMA) samples against γ rays was investigated in the absence and presence of poly(p‐sulfanilamide). Pure PMMA (without additives) and PMMA–poly(p‐sulfanilamide) blend samples were irradiated with γ rays for different exposure doses (5, 15, 25, 35, 50, 75, and 100 kGy). The viscosity‐average molecular weights were determined and thin‐layer chromatography measurements were carried out after each irradiation dose. The maximum protection against γ rays was found when 1% poly(p‐sulfanilamide) was used. The radiation chemical yield for main scission (G_s) was calculated and had lower values in the case of 1% poly(p‐sulfanilamide). The energy absorption per scission was maximum for 1% poly(p‐sulfanilamide), and this confirmed the obtained G_s data. From thin‐layer chromatography studies, it was observed that both the retention factor (R_f) values and polydispersity of the PMMA samples increased with an increasing exposure dose. The effect of γ irradiation on PMMA films doped with 1% poly(p‐sulfanilamide) was investigated with UV spectroscopy after the extraction of the additives. A change in the intensity of the absorption bands with an increasing irradiation dose was recorded. It is suggested that PMMA films doped with this type of polymer can be used as dosimeters. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Preparation and degradability of poly(lactic acid)–poly(ethylene glycol)–poly(lactic acid)/SiO2 hybrid material

Poly(lactic acid)–poly(ethylene glycol)–poly(lactic acid) (PLA‐PEG‐PLA)/SiO₂ hybrid material is prepared by sol–gel method using tetraethoxysilane (TEOS) and PLA‐PEG‐PLA as raw material. From Fourier transform infrared spectroscopy (FTIR) and X‐ray photoelectron spectroscopy (XPS) spectra, the hydroxyl groups of the silica sol derived from partially hydrolysis of TEOS and the unhydrolyzed ethoxy groups of TEOS can react with PLA‐PEG‐PLA. Differential scanning calorimetry (DSC) curves imply that the glass transition temperature (T_g) of PLA‐PEG‐PLA/SiO₂ hybrid material is higher than that of PLA‐PEG‐PLA and increases with the increase of silica content. X‐ray diffraction (XRD) analysis results show that PLA‐PEG‐PLA and PLA‐PEG‐PLA/SiO₂ hybrid material are both amorphous. Field scanning electron microscope (FSEM) photographs show that when PLA‐PEG‐PLA/SiO₂ hybrid material has been degraded for 12 weeks in normal saline at 37°C, a three‐dimensional porous scaffold is obtained, which is available for cell growth and metabolism. Moreover, the hydroxyl (? OH) groups on SiO₂ of PLA‐PEG‐PLA/SiO₂ hybrid material could buffer the acidity resulted from the degradation of PLA, which is beneficial to proliferation of cell in tissue repairing. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Synthesis,morphology, component distribution,and mechanical properties of nitrocellulose/gradient poly(ethylene glycol dimethacrylate) semi‐IPN material

Nitrocellulose (NC), a rigid natural polymer, was modified by gradient interpenetrating polymer networks containing poly(ethylene glycol dimethacrylate) (PEGDMA) to obtain both high strength and large toughness across the thickness from surface to the core of samples. PEGDMA content decreased with distance from the surface to core of nitrocellulose with a gradient of poly(ethylene glycol dimethacrylate) (NC/grad. PEGDMA) determined by elemental chemical analysis. The distribution of the guest component across the NC/grad. PEGDMA semi‐IPNs sample thickness was reciprocal function. SEM micrographs of NC/grad. PEGDMA semi‐IPNs revealed that, when the content of guest component was about 23%, the gradient system showed almost single phase morphology. At the same time, the tensile test results showed that NC/grad. PEGDMA featured both higher tensile strength and larger toughness. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Competitive hydrogen bonding mechanisms underlying phase behavior of triple poly(N‐vinyl pyrrolidone)–poly(ethylene glycol)–poly(methacrylic acid‐co‐ethylacrylate) blends

Differential scanning calorimetry (DSC) of triple blends of high molecular weight poly(N‐vinyl pyrrolidone) (PVP) with oligomeric poly(ethylene glycol) (PEG) of molecular weight 400 g/mol and copolymer of methacrylic acid with ethylacrylate (PMAA‐co‐EA) demonstrates partial miscibility of polymer components, which is due to formation of interpolymer hydrogen bonds (reversible crosslinking). Because both PVP and PMAA‐co‐EA are amorphous polymers and PEG exhibits crystalline phase, the DSC examination is informative on the phase state of PEG in the triple blends and reveals a strong competition between PEG and PMAA‐co‐EA for interaction with PVP. The hydrogen bonding in the triple PVP–PEG–PMAA‐co‐EA blends has been established with FTIR Spectroscopy. To evaluate the relative strengths of hydrogen bonded complexes in PVP–PEG–PMAA‐co‐EA blends, quantum‐chemical calculations were performed. According to this analysis, the energy of H‐bonding has been found to diminish in the order: PVP–PMAA‐co‐EA–PEG(OH) > PVP–(OH)PEG(OH)–PVP > PVP–H₂O > PVP–PEG(OH) > PMAA‐co‐EA–PEG(? O? ) > PVP–PMAA‐co‐EA > PMAA‐co‐EA–PEG(OH). Thus, most stable complexes are the triple PVP–PMAA‐co‐EA–PEG(OH) complex and the complex wherein comparatively short PEG chains form simultaneously two hydrogen bonds to PVP carbonyl groups through both terminal OH‐groups, acting as H‐bonding crosslinks between longer PVP backbones. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Improvement of the conductivity,electroactivity, and redoxability of polythiophene by electropolymerization of thiophene in the presence of catalytic amount of 1‐(2‐pyrrolyl)‐2‐(2‐thienyl) ethylene (PTE)

The electropolymerization of thiophene in the presence of 1‐(2‐pyrrolyl)‐2‐(2‐thienyl) ethylene (PTE) was investigated. PTE was synthesized via Wittig reaction and by the addition of catalytic amount of PTE during the electropolymerization of thiophene, the conditions of electropolymerization of thiophene were modified. The cyclic votammograms of polythiophenes (PThs) in different conditions were obtained. The analysis of cyclic votammograms of PThs shows a considerable increase in the electroactivity and redoxability when the electropolymerization of thiophene in the presence of catalytic amount of PTE was performed. The presence of PTE during electropolymerization of thiophene leads to an increase in the rate of polymerization too. The cyclic voltammetry (CV) measurement of electron transfer ferro/ferricyanide redox system on different modified glassy carbon (GC) electrode has shown that the rate of charge transfer for PTh in the presence of PTE increased in comparison to pure PTh. The conductivity of obtained polymers was determined by electrochemical impedance spectroscopy (EIS) technique in 3.5% (w/v) NaCl solutions. The Zview(II) software was applied to the EIS to estimate the parameters of the proposed equivalent circuit, based on a physical model for the electrochemical behavior of coatings on GC. The R_ct value obtained for PTh is 7667 Ω cm². This value decreases in the presence of PTE to 4437 Ω cm². Thus, the new film has more conductivity. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Preparation and characterization of poly(2‐chloroaniline)/SiO2 nanocomposite via oxidative polymerization: Comparative UV–vis studies into different solvents of poly(2‐chloroaniline) and poly(2‐chloroaniline)/SiO2

Poly(2‐chloroaniline)/silica (P2ClAn)/SiO₂ nanocomposites have been chemically prepared by oxidative polymerization of 2‐chloroaniline in acidic medium containing SiO₂. The prepared composites were characterized by FTIR, UV–vis, TGA, XRD, SEM, ESEM, conductivity, and magnetic susceptibility. The incorporation of P2ClAn in composites was endorsed by FTIR studies. The effect of the solution concentration of P2ClAn and P2ClAn/SiO₂ prepared in protonated, deprotonated, and reprotonated structures on the UV–vis spectra was investigated into three different solvents (DMF, NMP, and H₂SO₄). In all forms, the oxidation state of P2ClAn and P2ClAn/SiO₂ composite increased with increasing concentration of the testing solution into H₂SO₄. Thermogravimetric study exhibited that the composite has a higher thermal stability than P2ClAn. XRD measurement of the composite revealed that the crystal structure of incorporated SiO₂ undergone a distortion and converted into amorphous. Thus, the XRD pattern of P2ClAn was predominant. SEM analysis results revealed interesting morphological features for the composites converted to different forms and confirmed the formation of monodispersed composite particles. ESEM image of P2ClAn/SiO₂ has particle diameter of less than 1 μm. The conductivity of P2ClAn and P2ClAn/SiO₂ was measured by four‐probe technique. Magnetic susceptibility measurements revealed that the composite has a paramagnetic properties. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102:935–943, 2006     

Morphological,infrared, and ionic conductivity studies of poly(ethylene oxide)–49% poly(methyl methacrylate) grafted natural rubber–lithium perchlorate salt based solid polymer electrolytes

The potential of poly(ethylene oxide) (PEO) and 49% poly(methyl methacrylate) grafted natural rubber (MG49) as a polymer host in solid polymer electrolytes (SPE) was explored for electrochemical applications. PEO–MG49 SPEs with various weight percentages of lithium perchlorate salt (LiClO₄) was prepared with the solution casting technique. Characterization by scanning electron microscopy, Fourier transform infrared spectroscopy, and impedance spectroscopy was done to investigate the effect of LiClO₄ on the morphological properties, chemical interaction, and ionic conductivity behavior of PEO–MG49. Scanning electron microscopy analysis showed that the surface morphology of the sample underwent a change from rough to smooth with the addition of lithium salts. Infrared analysis showed that the interaction occurred in the polymer host between the oxygen atom from the ether group (C? O? C) and the Li⁺ cation from doping salts. The ionic conductivity value increased with the addition of salts because of the increase in charge carrier up to the optimum value. The highest ionic conductivity obtained was 8.0 × 10^?6 S/cm at 15 wt % LiClO₄. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Amphiphilic linear–hyperbranched polymer poly(ethylene glycol)–branched polyethylenimine–poly(ϵ‐caprolactone): synthesis,self‐assembly and application as stabilizer of platinum nanoparticles

Amphiphilic linear–hyperbranched polymer poly(ethylene glycol)–branched polyethylenimine–poly(?‐caprolactone) (PEG‐PEI‐PCL) was synthesized by progressively conjugating PEG (one chain) and PCL (multi‐chains) to PEI (hyperbranched architecture) with a yield of 87%. PEG‐PEI‐PCL forms nano‐sized uniform spherical micelles by self‐assembly in water. The micelles had an average diameter of 56 nm determined using dynamic light scattering and 35 nm observed from transmission electron microscopy images. PEG‐PEI‐PCL was used as a stabilizer of platinum nanoparticles (PtNPs) for the first time. The particle diameter of PEG‐PEI‐PCL‐stabilized PtNPs was 7.8 ± 1.4 nm. Amphiphilic (hydrophilic–hydrophilic–hydrophobic) and hyperbranched (linear–hyperbranched–grafted) structures enabled PtNPs to effectively stabilize and disperse in liquid‐phase synthesis. The highly disperse PtNPs in PEG‐PEI‐PCL micelles improved the catalytic activity for the reduction of 4‐nitrophenol with a catalytic yield of near 100%. © 2016 Society of Chemical Industry     

Thermal,structural, and optical properties of γ‐irradiated poly(vinyl alcohol)/poly(ethylene glycol) thin film

Poly(vinyl alcohol)/poly(ethylene glycol) (PVA/PEG) copolymer was prepared using casting technique. The obtained PVA/PEG thin films have been irradiated with gamma rays with doses ranging from 1.5 to 20 Gy. The resultant effect of gamma irradiation on the thermal properties of PVA/PEG has been investigated using thermogravimetric analysis (TGA) and differential thermal analysis (DTA). The onset temperature of decomposition T_o and activation energy of thermal decomposition E_a were calculated, results indicating that the PVA/PEG thin film decomposes in one main weight loss stage. Also, the gamma irradiation in dose range 4–12 Gy led to a more compact structure of PVA/PEG copolymer, which resulted in an improvement in its thermal stability with an increase in the activation energy of thermal decomposition. The variation of transition temperatures with gamma dose has been determined using DTA. The PVA/PEG thermograms were characterized by the appearance of an endothermic peak due to melting of crystalline phase. In addition, structural property studies using X‐ray diffraction and infrared spectroscopy were performed on both nonirradiated and irradiated samples. Furthermore, the transmission of the PVA/PEG samples and any color changes were studied. The color intensity (E was greatly increased with increasing the gamma dose and was accompanied by a significant increase in the blue and green color components. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Degradation of poly(D,L‐lactic acid)‐b‐poly(ethylene glycol) copolymer and poly(L‐lactic acid) by electron beam irradiation

This article investigated the effects of electron beam (EB) irradiation on poly(D ,L ‐lactic acid)‐b‐poly(ethylene glycol) copolymer (PLEG) and poly(L ‐lactic acid) (PLLA). The dominant effect of EB irradiation on both PLEG and PLLA was chain scission. With increasing dose, recombination reactions or partial crosslinking of PLEG can occur in addition to chain scission, but there was no obvious crosslinking for PLLA at doses below 200 kGy. The chain scission degree of irradiated PLEG and PLLA was calculated to be 0.213 and 0.403, respectively. The linear relationships were also established between the decrease in molecular weight with increasing dose. Elongation at break of the irradiated PLEG and PLLA decreased significantly, whereas the tensile strength and glass transition temperature of PLLA decreased much more significantly compared with PLEG. The presence of poly(ethylene glycol) (PEG) chain segment in PLEG was the key factor in its greater stability to EB irradiation compared with PLLA. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Fabrication of polymer‐gadolinium (III) complex nanomicelle from poly(ethylene glycol)‐polysuccinimide conjugate and diethylenetriaminetetraacetic acid‐gadolinium as magnetic resonance imaging contrast agents

Methoxy poly (ethylene glycol)‐graft‐α, β‐poly (aspartic acid) derivatives (mPEG‐g‐PAA‐N₃) were synthesized by sequential ring‐opening reaction of polysuccinimide (PSI) with mPEG‐NH₂ (MW: 2000 Da), and 1‐azido‐3‐aminopropane, respectively. Then N²‐(hex‐5‐yne)‐diethylenetriamine‐tetra‐t‐butylacetate (DTTA‐der) was conjugated to mPEG‐g‐PAA‐N₃ by click cycloaddition. After deprotection of carboxylic groups, mPEG‐g‐PAA‐DTTA macromolecular ligands were obtained. MPEG‐g‐PAA‐(DTTA‐Gd) complex nanomicelles were fabricated from mPEG‐g‐PAA‐DTTA and Gadolinium chloride. The formation of nanomicelles was confirmed by fluorescence spectrophotoscopy and particle size measurements. It was found that all the nanomicelles showed spherical shapes with core‐shell structures and narrow size distributions. Their sizes ranged from 50 to 80 nm, suggesting their passive targeting potential to tumor tissue. With the increase of graft degree (GD) of mPEG, the sizes of mPEG‐g‐PAA‐(DTTA‐Gd) nanomicelles showed a tendency to decrease. Compared with gadopentetate dimeglumine (Gd‐DTPA), mPEG‐g‐PAA‐(DTTA‐Gd) nanomicelles showed essential decreased cytotoxicity to KB cell line and enhanced T₁‐weighted signal intensity, especially at low concentration of gadolinium (III), suggesting their great potentials as magnetic resonance imaging contrast agents. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Sequence length determination in poly(ethylene terephthalate)–bisphenol-A polycarbonate random copolymers by application of selective degradation

Poly(ethylene terephthalate) (PET) and bisphenol-A polycarbonate (PC) are melt-mixed in equimolar ratios under various conditions to get a series of PET–PC copolymers. Samples from each copolymer are characterized by differential scanning calorimetry, ¹H and ¹³C nuclear magnetic resonance (NMR), size exclusion chromatography (SEC), and polarizing light microscopy. The lengths of the PET sequences are determined in different copolymer samples by NMR sequential analysis before and after removal of the PC segments by selective degradation. In the former case, rather unusual results are obtained, suggesting predominant alternating order of single PET and PC repeating units. After selective elimination of the PC units, however, the NMR techniques show evidence of consecutively bonded dyads or triads of PET and PC units, which corresponds to the theoretical values in random copolymers obeying the statistics of Bernoulli. Considering the ¹H-NMR and SEC results after selective elimination of the PC sequences, a possible structure of the residual PET containing segments is proposed for the first time. It is concluded that in the PET/PC copolymers studied, when sequence distribution approaches the random one, determination of the PET block lengths after elimination of the PC sequences is more reliable as compared to the cases when selective degradation is not applied. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 68: 429–440, 1998     

Kinetic study of emulsion copolymerization of ethyl methacrylate/lauryl methacrylate in propylene glycol,stabilized with poly(ethylene oxide)–block–polystyrene–block–poly(ethylene oxide) triblock copolymer

The kinetics of emulsion copolymerization of ethyl methacrylate (EMA)/lauryl methacrylate (LMA) in propylene glycol is very similar to the emulsion copolymerizations of water‐soluble monomers in water because of the high solubility of EMA/LMA in propylene glycol. The initial rate of polymerization depends only on initiator concentration and is not affected by either monomer concentration or stabilizer concentration. The overall rate of polymerization is only slightly dependent on monomer concentration and stabilizer concentration and is independent of initiator concentration. The final particle number density increases with increasing amount of stabilizer and decreases with increasing monomer concentration. The total surface area increases with stabilizer concentration and is not governed by either initiator concentration or monomer concentration. Homogeneous nucleation is the dominant mechanism of particle nucleation, as shown by the kinetic data on seeded polymerization and monomer partition behavior. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 82: 1691–1704, 2001     

Measurement of the electrochemical response time and electron paramagnetic resonance behavior of poly(o‐phenetidine)–poly(styrene sulfonic acid) and poly(2‐ethylaniline)–poly(styrene sulfonic acid) complexes

Two studies were mainly focused on the measurement of electrochemical response time and the electron paramagnetic resonance (EPR) of the substituted polyaniline (PANI) complexes poly(o‐phenetidine) (POP)–poly(styrene sulfonic acid) (PSSA) and poly(2‐ethylaniline) (P2E)–PSSA, which were prepared by the electrochemical polymerization of the monomer (o‐phenetidine or 2‐ethylaniline) with PSSA, with indium tin oxide (ITO) as a working electrode in a 1M HCl solution. Ultraviolet–visible spectra measurements showed evidence for the doped substituted PANI system to have a highly electrochemical response time recorded at a temperature of 298 K, and the results were further analyzed on the basis of the color–discolor model, which is typical of protonation systems. At the reaction time (3 s) and monomer concentration (0.6M) with PSSA (0.15 μ), the best electrochemical color/discolor time of the POP–PSSA complexes was 125/125 ms (thickness = 3.00 μm), which was faster than that of the P2E–PSSA complexes. At the same thickness (10 μm), the best electrochemical color/discolor time of the POP–PSSA complexes was 500/250 ms, which was faster than the P2E–PSSA complexes (750/500 ms). With regard to film growth rate, the POP–PSSA complexes (1.0 μm/s) were faster than the P2E–PSSA complexes (0.79 μm/s); this was attributed to the substituted PANI having a steric effect and to good reactivity by the ethoxy group (? OC₂H₅) in the molecules. The EPR spectra of the two samples were recorded both at 298 and 77 K and were further analyzed on the basis of the polaron–bipolaron model. The narrower line width of the substituted PANI complexes arose due to polarons; that is, we propose that charge transport took place through both polarons and bipolarons. Compared to their salts, this could be attributed to the lower degree of structural disorder, the oxygen absorption on the molecules, and the steric effect by the side chain group. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 96: 1211–1221, 2005     

A study of solvent exchange process in (ethylene–vinyl alcohol) copolymer gels by a proton nuclear magnetic resonance spectroscopy imaging method

The proton nuclear magnetic resonance (¹H NMR) image patterns of (ethylene–vinyl alcohol) copolymer (EVOH)/dimethylsulfoxide (DMSO) gels with various ethylene contents were measured to elucidate the process of solvent exchange between DMSO and water in the gels soaked in water. The results of these experiments indicate that the rate of solvent exchange between DMSO and water in the gels increased with an increase in the ethylene content of EVOH copolymers. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 504–508, 2002     

Blood protein adsorption onto macroporous semi‐interpenetrating polymer networks (IPNs) of poly(ethylene glycol) (PEG) and poly(2‐hydroxyethyl methacrylate) (PHEMA) and assessment of in vitro blood compatibility

This work reports a study of the adsorption of fibrinogen (Fgn) onto the surface of semi‐interpenetrating polymer networks (IPNs) of poly(ethylene glycol) (PEG) and poly(2‐hydroxyethyl methacrylate) (PHEMA). The semi‐IPNs were prepared by polymerizing 2‐hydroxyethyl methacrylate with a redox system and in the presence of PEG and crosslinker ethyleneglycol dimethacrylate. The proposed spongy IPNs were characterized by Fourier transform infrared and environmental scanning electron microscopy methods, and network structural parameters, such as molecular weight between crosslinks and crosslink density, were calculated using swelling measurements. The adsorption of Fgn was carried out onto the spongy IPNs and kinetic constants of the adsorption process as well as isotherm constants were evaluated. The adsorption process was also studied under varying pH, ionic strengths, and chemical architecture of the IPNs. The anti‐thrombogenic behaviour of the polymer matrices was judged using in vitro tests. Copyright © 2006 Society of Chemical Industry     

Preparation of new dendrimer‐like star‐shaped amphiphilic poly(ethylene glycol)–poly(ϵ‐caprolactone) copolymers for biocompatible and high‐efficiency curcumin delivery

Novel amphiphilic star‐shaped terpolymers comprised of hydrophobic poly(?‐caprolactone), pH‐sensitive polyaminoester block and hydrophilic poly(ethylene glycol) (M_n = 1100, 2000 g mol^?1) were synthesized using symmetric pentaerythritol as the core initiator for ring‐opening polymerization (ROP) reaction of ?‐caprolactone functionalized with amino ester dendrimer structure at all chain ends. Subsequently, a second ROP reaction was performed by means of four‐arm star‐shaped poly(?‐caprolactone) macromer with eight ‐OH end groups as the macro‐initiator followed by the attachment of a poly(ethylene glycol) block at the end of each chain via a macromolecular coupling reaction. The molecular structures were verified using Fourier transform infrared and ¹H NMR spectroscopies and gel permeation chromatography. The terpolymers easily formed core–shell structural nanoparticles as micelles in aqueous solution which enhanced drug solubility. The hydrodynamic diameter of these agglomerates was found to be 91–104 nm, as measured using dynamic light scattering. The hydrophobic anticancer drug curcumin was loaded effectively into the polymeric micelles. The drug‐loaded nanoparticles were characterized for drug loading content, encapsulation efficiency, drug–polymer interaction and in vitro drug release profiles. Drug release studies showed an initial burst followed by a sustained release of the entrapped drug over a period of 7days at pH = 7.4 and 5.5. The release behaviours from the obtained drug‐loaded nanoparticles indicated that the rate of drug release could be effectively controlled by pH value. Altogether, these results demonstrate that the designed nanoparticles have great potential as hydrophobic drug delivery carriers for cancer therapy. © 2015 Society of Chemical Industry     

Poly(ethylene terephthalate)–poly(caprolactone) block copolymer. I. Synthesis,reactive extrusion,and fiber morphology

A novel poly(ethylene terephthalate)–poly(caprolactone) block copolymer (PET–PCL) is synthesized in a reactive twin‐screw extrusion process. In the presence of stannous octoate, ring‐opening polymerization of ϵ‐caprolactone is initiated by the hydroxyl end groups of molten PET to form polycaprolactone blocks. A block copolymer with minimal transesterification is obtained in a twin‐screw extruder as a consequence of the fast distributive mixing of ϵ‐caprolactone into high melt viscosity PET and the short reaction time. The PET–PCL structure is characterized by IV, GPC, ¹H‐NMR, and DSC. Fully drawn and partially relaxed fibers spun from PET–PCL are characterized by WAXD and SAXS. A substantial decrease in the oriented amorphous fraction appears to be the major structural change in the relaxed fiber that provides the fiber with the desired stress–strain characteristics. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 1858–1867, 1999