A 3-5 GHz TH-UWB transmitter in 0.18-μm RF CMOS technology

5 mV at a 50 Ω load from a 1.8-V supply, the return loss (S11) at the output port is less than -10 dB, and the chip size is 0.7 × 0.8 mm2, with a power consumption of 12.3 mW.     

LC voltage controlled oscillator in 0.18-μm RF CMOS

An integrated low-phase-noise voltage-controlled oscillator(VCO) has been designed and fabricated in SMIC 0.18μm RF CMOS technology.The circuit employs an optimally designed LC resonator and a differential cross-coupling amplifier acts as a negative resistor to compensate the energy loss of the resonator.To extend the frequency tuning range,a three-bit binary-weighted switched capacitor array is used in the circuit.The testing result indicates that the VCO achieves a tuning range of 60%from 1.92 to 3.35 GHz.The phase noise of the VCO is -117.8 dBc/Hz at 1 MHz offset from the carrier frequency of 2.4 GHz.It draws 5.6 mA current from a 1.8 V supply.The VCO integrated circuit occupies a die area of 600×900μm~2.It can be used in the IEEE802.11 b based wireless local network receiver.     

0.18μm RF CMOS双向可控硅ESD防护器件的研究(英文)

基于传统双向可控硅(DDSCR)提出了两种静电放电(ESD)保护器件,可应对正、负ESD应力从而在2个方向上对电路进行保护。传统的DDSCR通过N-well与P-well之间的雪崩击穿来触发,而提出的新器件则通过嵌入的NMOS/PMOS来改变触发机制、降低触发电压。两种改进结构均在0.18μmRFCMOS下进行流片,并使用传输线脉冲测试系统进行测试。实验数据表明,这两种新器件具有低触发电压、低漏电流(～nA),抗ESD能力均超过人体模型2kV,同时具有较高的维持电压(均超过3.3V),可保证其可靠地用于1.8V、3.3V I/O端口而避免出现闩锁问题。     

High LO-RF isolation of zero-IF mixer in 0.18 μm CMOS technology

In this study, we introduce a zero-IF sub-harmonic mixer with high isolation in the 5 GHz band using 0.18 μm CMOS technology. Placing an LC-Tank between the class AB stage and the mixer core improves the isolation between the LO to RF at low supply voltage. The measured isolation is 48 dB between the LO and RF ports, and the 9.5 dB conversion gain is achieved with a supply voltage of 7 mA at 2.5 V. In order to alleviate the degradation of linearity due to the high conversion gain, we adopt the class AB stage as RF input stage. The measured IIP₃ is −7.5 dBm. This work was supported by National Science Council of Taiwan, ROC under contract no. NSC94-2220-E-005-002.     

A 5-GHz programmable frequency divider in 0.18-μm CMOS technology

正A 5-GHz CMOS programmable frequency divider whose modulus can be varied from 2403 to 2480 for 2.4-GHz ZigBee applications is presented.The divider based on a dual-modulus prescaler(DMP) and pulse-swallow counter is designed to reduce power consumption and chip area.Implemented in the 0.18-μm mixed-signal CMOS process,the divider operates over a wide range of 1-7.4 GHz with an input signal of 7.5 dBm;the programmable divider output phase noise is -125.3 dBc/Hz at an offset of 100 kHz.The core circuit without test buffer consumes 4.3 mA current from a 1.8 V power supply and occupies a chip area of approximately 0.015 mm~2.The experimental results indicate that the programmable divider works well for its application in frequency synthesizers.     

A 7-GHz multiloop ring oscillator in 0.18-μm CMOS technology

A novel delay stage for ring oscillator utilizing multiloop technique is presented in this paper. Different conventional delay stages for the multiloop ring oscillators have been reviewed and analyzed in this work. By using push-pull inverter as the secondary input in its delay cell, the proposed oscillator demonstrates a frequency improvement of up to 17% when compared with conventional designs. The fabricated oscillator is measured to cover a frequency range of 6.24–7.04 GHz. Operating in 1.8-V power supply, the oscillator manifests itself a phase noise of ?107.7 dBc/Hz@10 MHz offset from a center frequency of 6.25 GHz. The proposed oscillator consumes a current of 40–51 mA from the 1.8-V supply and occupies an area of 440 μm ×  430 μm.     

A 5.25-GHz low-power down-conversion mixer in 0.18-μm CMOS technology

A 5.25 GHz low voltage, high linear and isolated mixer using TSMC 0.18 μm CMOS process for WLAN receiver was investigated. The paper presents a novel topology mixer that leads to better performance in terms of linearity, isolation and power consumption for low supply voltage. The measuring results of the proposed mixer achieve: 7.6 dB power conversion gain, 11.4 dB double side band noise figure, 3 dBm input third-order intercept point, and the total dc power consumption of this mixer including output buffers is 2.45 mW from a 1 V supply voltage. The current output buffer is about 2 mW, the excellent LO-RF, LO-IF and RF-IF isolation achieved up to 37.8, 54.8 and 38.2 dB, respectively.     

A RF receiver frontend for SC-UWB in a 0.18-μm CMOS process

正A radio frequency(RF) receiver frontend for single-carrier ultra-wideband(SC-UWB) is presented. The front end employs direct-conversion architecture,and consists of a differential low noise amplifier(LNA),a quadrature mixer,and two intermediate frequency(IF) amplifiers.The proposed LNA employs source inductively degenerated topology.First,the expression of input impedance matching bandwidth in terms of gate-source capacitance, resonant frequency and target S_(11) is given.Then,a noise figure optimization strategy under gain and power constraints is proposed,with consideration of the integrated gate inductor,the bond-wire inductance,and its variation.The LNA utilizes two stages with different resonant frequencies to acquire flat gain over the 7.1-8.1 GHz frequency band,and has two gain modes to obtain a higher receiver dynamic range.The mixer uses a double balanced Gilbert structure.The front end is fabricated in a TSMC 0.18-/im RF CMOS process and occupies an area of 1.43 mm~2.In high and low gain modes,the measured maximum conversion gain are 42 dB and 22 dB,input 1 dB compression points are -40 dBm and -20 dBm,and S_(11) is better than -18 dB and -14.5 dB.The 3 dB IF bandwidth is more than 500 MHz.The double sideband noise figure is 4.7 dB in high gain mode.The total power consumption is 65 mW from a 1.8 V supply.     

0.18μm RF CMOS 3-5 GHz TH-UWB 通信射频发信机

本文给出一种3-5 GHz射频TH-UWB发信机的设计。该发信机由一个4GHz的振荡器,一个带衰减控制的MOS开关和一个输出匹配电路构成。由低速TH-PPM信号控制,该发信机输出中心频率为4GHz的TH-UWB信号,并能直接通过传输线驱动天线。采用0.18μm RF CMOS工艺实现,在1.8V电源下,输出信号峰值幅度在50Ω负载上为65mV。电路输出端口回波损耗S11小于-10dB。芯片占用面积为0.7 mm0.8 mm,功耗为12.3mW。     

A 900 MHz fractional-N synthesizer for UHF transceiver in 0.18μm CMOS technology

A 900 MHz fractional-N synthesizer is designed for the UHF transceiver. The VCO with a 4 bits capacitor bank covers 823–1061 MHz that implements 16(24)sub-bands. A 7/8 dual-modulus prescaler is implemented with a phase-switching circuit and high-speed flip–flops, which are composed of source coupled logic. The proposed synthesizer phase-locked loop is demonstrated with a 50 k Hz band width by a low 12.95 MHz reference clock, and offers a better phase noise and band width tradeoff. To reduce the out-band phase noise, a 4-levels 3-order single-loop sigma–delta modulator is applied. When its relative frequency resolution is settled to 10-6, the testing results show that the phase noises are –120.6 d Bc/Hz at 1 MHz and –95.0 d Bc/Hz at 100 k Hz. The chip is2.1 mm2 in UMC 0.18μm CMOS. The power is 36 m W at a 1.8 V supply.     

Design of GGNMOS ESD protection device for radiation-hardened 0.18 μm CMOS process

In this paper, the ESD discharge capability of GGNMOS (gate grounded NMOS) device in the radiation-hardened 0.18 μm bulk silicon CMOS process (Rad-Hard by Process: RHBP) is optimized by layout and ion implantation design. The effects of gate length, DCGS and ESD ion implantation of GGNMOS on discharge current density and lattice temperature are studied by TCAD and device simulation. The size of DCGS, multi finger number and single finger width of ESD verification structures are designed, and the discharge capacity and efficiency of GGNMOS devices in ESD are characterized by TLP test technology. Finally, the optimized GGNMOS is verified on the DSP circuit, and its ESD performance is over 3500 V in HBM mode.     

Method of simulation of low dose rate for total dose effect in 0.18/μm CMOS technology

tailed information on the behavior of the test devices in a low dose rate environment.     

A 5-GHz programmable frequency divider in 0.18-μM CMOS technology

A 5-GHz CMOS programmable frequency divider whose modulus can be varied from 2403 to 2480 for 2.4-GHz ZigBee applications is presented.The divider based on a dual-modulus prescaler (DMP) and pulse-swallow counter is designed to reduce power consumption and chip area.Implemented in the 0.18-μm mixed-signal CMOS process,the divider operates over a wide range of 1-7.4 GHz with an input signal of 7.5 dBm; the programmable divider output phase noise is -125.3 dBc/Hz at an offset of 100 kHz.The core circuit without test buffer consumes 4.3 mA current from a 1.8 V power supply and occupies a chip area of approximately 0.015 mm2.The experimental results indicate that the programmable divider works well for its application in frequency synthesizers.     

A 1.2-V, 84-dB Σ△ ADM in 0.18-μm digital CMOS technology

A low power and low voltage∑△analog-to-digital modulator is realized with digital CMOS technology, which is due to full compensated depletion mode capacitors.Compared with mixed signal technology,this type of modulator is more compatible for pure digital applications.A pseudo-two-stage class-AB OTA is used in switchedcapacitor integrators for low voltage and low power.The modulator is realized in standard SMIC 0.18μm 1P6M digital CMOS technology.Measured results show that with 1.2 V supply voltage and a 6 MHz sample clock,the dynamic range of the modulator is 84 dB and the total power dissipation is 2460μW.     

5 GHz 0.18-μm CMOS 可编程分频器

提出了一种2.4GHz ZigBee 应用的可编程分频器,其分频模值在2403-2480之间变化。该分频器基于双模分频器和吞咽计数器架构,功耗和面积得到了有效降低。芯片采用0.18-μm CMOS混合信号工艺实现,当输入信号达到7.5dBm时,分频器可正常工作的频率范围覆盖1-7.4 GHz,在100KHz频偏处的输出相位噪声为-125.3dBc/Hz。分频器核心电路消耗电流4.3mA（1.8V电源电压）,核心面积0.015mm2。测试结果表明该可编程分频器能很好的应用在所需的频率综合器中.     

A 6.25 Gb/s equalizer in 0.18μm CMOS technology for high-speed SerDes

This paper presents a 0.18μm CMOS 6.25 Gb/s equalizer for high speed backplane communication. The proposed equalizer is a combined one consisting of a one-tap feed-forward equalizer （FFE） and a two-tap half-rate decision feedback equalizer （DFE） in order to cancel both pre-cursor and post-cursor ISI. By employing an active-inductive peaking circuit for the delay line, the bandwidth of the FFE is increased and the area cost is minimized. CML-based circuits such as DFFs, summers and multiplexes all help to improve the speed of DFEs. Measurement results illustrate that the equalizer operates well when equalizing 6.25 Gb/s data is passed over a 30-inch channel with a loss of 22 dB and consumes 55.8 mW with the supply voltage of 1.8 V. The overall chip area including pads is 0.3 × 0.5 mm^2.     

0.18μm CMOS可编程增益放大器

介绍了一种基于0.18μm CMOS工艺,应用于5 GHz无线局域网(WLAN)的可编程增益放大器(PGA)。该PGA采用分级可选放大器的系统结构,核心电路由交叉耦合的共源共栅放大器和电流反馈放大器组成。为消除工艺角偏差对增益精度的影响,设计中加入了增益微调的机制。后仿真结果表明:PGA电压增益可在0 dB到41 dB之间以1 dB步长变化,双端输出的电压摆幅为1 Vp-p,并具有大于10 MHz的-3 dB带宽和小于21.1 mW的静态功耗。     

Design of a 0.18μm CMOS multi-band compatible low power GNSS receiver RF frontend

This paper presents the design and implementation of a fully integrated multi-band RF receiver frontend for GNSS applications on L-band.A single RF signal channel with a low-IF architecture is adopted for multi-band operation on the RF section,which mainly consists of a low noise amplifier(LNA),a down-converter,polyphase filters and summing circuits.An improved cascode source degenerated LNA with a multi-band shared off-chip matching network and band switches is implemented in the first amplifying stage....     

Design of a high-order single-loop Σ△ ADC followed by a decimator in 0.18μm CMOS technology

This work presents an oversampled high-order single-loop single-bit sigma–delta analog-to-digital converter followed by a multi-stage decimation filter.Design details and measurement results for the whole chip are presented for a TSMC 0.18μm CMOS implementation to achieve virtually ideal 16-b performance over a baseband of 640 kHz.The modulator in this work is a fully differential circuit that operates from a single 1.8 V power supply. With an oversampling ratio of 64 and a clock rate of 81.92 MHz,the modulator achieves a 94 dB dynamic range. The decimator achieves a pass-band ripple of less than 0.01 dB,a stop-band attenuation of 80 dB and a transition band from 640 to 740 kHz.The whole chip consumes only 56 mW for a 1.28 MHz output rate and occupies a die area of 1×2 mm^2.