Aluminum nitride ceramics were prepared by sintering with 0–4.8 mass% of Ca3Al2O6 (C3A) as a sintering additive. The transmittance in the range of 260–550 nm increased with increasing amount of C3A. The cathodoluminescence intensity attributed to oxygen-induced defects decreased with increasing amount of C3A. From the results, the increase of the transmittance in the range of 260–550 nm was considered to be related to the decrease of the oxygen-induced defect density. 相似文献
A modified Monte Carlo (MC) simulation was performed to investigate the hydrogen absorption behavior in Pd and Pd–Ag alloys of the composition PdxAg1−x (x=0.7–0.8) under H2 pressure (0.1 MPa) at different temperatures. The present method employed can consider the dissociative adsorption of hydrogen molecule and the subsequent absorption of hydrogen atom by formalizing the relationship between the pressure of hydrogen molecule and hydrogen atom. The potential parameters were determined to reproduce the solution enthalpy of hydrogen in pure metals. The results are in good agreement with experimental findings as well as previous theoretical studies. We confirmed that our method is useful to simulate the absorption of hydrogen in metals and alloys. 相似文献
A high powered YAG laser with kaleidoscope for surface modification was applied to the surface hardening of carbon steels containing 0. 18-0.54 wt% C without the absorbents, and the relationships between laser processing and surface hardening were investigated by hardness and microstructure. The structure of the hardened zone underwent complete martensitic transformation in all of the carbon steels tested, and its hardness increased with greater carbon content. Under identical irradiated conditions, the hardened zone expanded with increasing carbon content. A hardened zone extending from the surface to a depth of 1.0 mm was obtained at a laser power of 1.0 kW and a scanning speed of 1 mm/sec. It was found that in the surface hardening of carbon steels, a high powered YAG laser can be used to control the hardened zone by selecting the appropriate irradiation conditions, however, the hardened zone was affected by the assistant gas and the flow rate. 相似文献
Flexural properties of moldings made by Reaction Injection Molding (RIM), which are structural foams consisting of high density skin and low density core, were investigated by three-point bending tests. Two failure modes were observed in bending tests of the moldings made by RIM, and they are classified as follows according to the density ratio of skin layer to core layer: the opposite side of the skin layer to which load was subjected failed by tensile stress: and the same side of the skin layer to which load was subjected failed by compressive stress, causing wrinkling or buckling. Then the conventional composite beam theory was applied to the former failure mode and Hoff s buckling theory to the latter, and equations were derived to predict the flexural properties of the structural foams, which involved buckling from the flexural properties of solid construction. In addition, it has been shown that there exists a density distribution that maximizes the flexural strength of the moldings made by RIM with a given overall density. The results obtained here should be useful to the optimum structural design of moldings made by RIM. 相似文献
Rac, a member of the rho family of GTPases, when activated transmits signals leading to actin-based membrane ruffling in fibroblasts. Compared with wild-type fibroblasts, gelsolin null (Gsn-) dermal fibroblasts have a markedly reduced ruffling response to serum or EGF stimulation, which signal through rac. Bradykinin-induced filopodial formation, attributable to activation of cdc42, is similar in both cell types. Wild-type fibroblasts exhibit typical lamellipodial extension during translational locomotion, whereas Gsn- cells move 50% slower using structures resembling filopodia. Multiple Gsn- tissues as well as Gsn- fibroblasts overexpress rac, but not cdc42 or rho, 5-fold. Re-expression of gelsolin in Gsn- fibroblasts by stable transfection or adenovirus reverts the ruffling response, translational motility and rac expression to normal. Rac migrates to the cell membrane following EGF stimulation in both cell types. Gelsolin is an essential effector of rac-mediated actin dynamics, acting downstream of rac recruitment to the membrane. 相似文献
Bovine pancreatic /S-trypsin (PDB ID-code: 1TPO) which is registeredin the Brookhaven Protein Data Bank (PDB) consists of four exons.The results of homology searches for each exon in the PDB showedthat homologous proteins were tonin (PDB ID-code: 1TON), ratmast cell protease (PDB ID-code: 3RP2_A), kaffikrein A (PDBID-code: 2PKA_B) and kallikrein A (2PKA_B) respectively. Thus,for the three-dimensional structure prediction of 1TPO, a chimeraprotein was constructed from the three proteins mentioned aboveand the 3-D structure prediction was performed using this chimerareference protein. The modelled structure of 1TPO was energeticallyoptimized by molecular mechanics and molecular dynamics simulationand was compared with its X-ray crystal structure registeredin the PDB. The root mean square deviations (r.m.s.d.) of mainchain atoms and the neighbouring active site (5 sphere fromHis57, AsplO2 and Serl95) between the modelled structure andthe X-ray structure were 1.66 and 0.94 respectively. Porcinepancreatic elastase (PDB ID-code: 3EST) which is registeredin the PDB was used as the reference protein and the modelledstructure from 3EST was also compared with the X-ray data. Ther.m.s.d. of main chain atoms and that of the active site were2.14 and 1.18 respectively. These results dearly support thepropriety of this method using the chimera reference protein. 相似文献
Zr-Al organometallic compounds have been spray-dried and heated at temperatures 600 to 1400°C to prepare ZrO2-Al2O3 composite powders. The powders consist of balloon-like particles 0.5 to 2 m in diameter with homogeneously dispersed tetragonal ZrO2 grains 0.1 to 0.2 m in diameter. The tetragonal fraction of ZrO2 in the composite powders is higher than that in the powders prepared from sols of Zr(OBun)4 and Al[OCH(CH3)2]3. The fraction is affected by the organofunctional group in the Zr-Al compounds.Zr(OBun)4 = Zr(OC4Hgn)4; Al[OCH(CH3)2]3 = Al(OPri)3. 相似文献
The impact of micro-alloying on tensile behavior at strain rates in various ranges is examined using five types of extruded Mg-0.3 at. pct Mn–0.1 at. pct X ternary alloys, where X is selected as a common element, Al, Li, Sn, Y or Zn. Microstructural observations reveal that the average grain size of these extruded alloys is between 1 and 3 μm, and these micro-alloying elements segregate at grain boundaries. In room temperature tensile and compression tests, these results show that the mechanical properties and deformation behavior are influenced by the micro-alloying element, even as a small addition of 0.1 at. pct. Mg–Mn–Y and Mg–Mn-Zn alloys show higher strength and smaller strain rate sensitivity (m-value) among the present alloys, owing to the rate-controlling mechanism as dislocation slip. On the other hand, the Mg–Mn–Li alloy exhibits the largest elongation to failure in tension and the highest strain rate sensitivity, associated with high contribution of grain boundary sliding to deformation. These differences are due to the grain boundary segregation of the micro-alloying elements. Compared to the common Mg alloys, the present ternary alloys also show a trade-off relationship between strength and ductility, which is similar to that of the well-known Mg alloys; however, these properties of the Mg–Mn system ternary alloys could be controlled via the type of micro-alloying elements with a chemical content of 0.1 at. pct.