Applications and Technologies of All-Solid State Blue Laser

1 Introduction Along with the matureness of laser diode (LD) manufacturing technology, the performance of LD has been improved greatly since 1980s, so various kinds of laser devices based on LD have been developed rapidly, especially the all-solid state lasers. After early experiments and researches, the all-solid state lasers have been commercialized successfully.     

Microscale Patterning of Mesoscopic PZN-PT Single Crystal Films by Crystal ion Slicing and Laser-Induced Etching

Advances in the fabrication of solid-solution single crystal relaxor ferroelectrics have made it possible to produce highly efficient piezoelectric crystals, and have attracted renewed interest in the use of these crystals for a new generation of piezoelectric transducers, actuators and sensors. Of particular interest is their incorporation into micro-electromechanical systems (MEMS). In this paper we report on the laser-induced wet chemical etching of lead zinc niobate-lead titanate (PZN-PT) in hydrochloric acid (HCl). Argon-ion laser radiation at power levels up to 4 W is focused to a spot diameter of about 15μm and results in the chemical etching of grooves at patterning speeds up to 5μm/sec. Crystal ion slicing, an ion-implant-based film separation technique, is used in combination with laser etching to form 5 to 10μm-thick patterned and freestanding films for incorporation into micro-electromechanical devices.     

A concise process technology for 3-D suspended radio frequency micro-inductors on silicon substrate

In this letter, a concise process technology is proposed for the first time to enable the fabrication of good quality three-dimensional (3-D) suspended radio frequency (RF) micro-inductors on bulk silicon, without utilizing the lithography process on sidewall and trench-bottom patterning. Samples were fabricated to demonstrate the applicability of the proposed process technology.     

An efficient mixed algorithm of L-MEI and DDM for the wavescattering by a concave cylinder

In this paper, a localized MEI method (L-MEI) is developed and combined with the domain decomposition method (DDM) for the simulation of scattering by a concave cylinder. In the L-MEI, the whole domain is decomposed into many subdomains. Different from the conventional MEI method, the MEI coefficients of the L-MEI method in each subdomain are only dependent on the localized metrons that are defined in the subdomain. The localization of metrons has the following advantages: (1) speeding up the calculation of MEI coefficients and saving memory, (2) making the MEI method available for concave structures, and (3) obtaining a band sparse matrix directly without any modification     

An EM‐based adaptive multiple target tracking filter

Tracking targets of interest is one of the major research areas in radar surveillance systems. We formulate the problem as incomplete data estimation and apply EM to the MAP estimate. The resulting filter has a recursive structure analogous to the Kalman filter. The advantage is that the measurement‐update deals with multiple measurements in parallel and the parameter‐update estimates the system parameters on the fly. Experiments tracking separate targets in parallel show that tracking maintenance ratio of the proposed system is better than that of NNF and RMS position error is smaller than that of PDAF. Also, the system parameters are correctly obtained even from incorrect initial values. Copyright © 2001 John Wiley & Sons, Ltd.     

Direct adaptive control of nonminimum phase systems using integralaction

A direct adaptive control scheme is proposed for nonminimum-phase systems in which controller parameters are estimated from the recursive least-squares algorithm and additional auxiliary parameters are obtained from the proposed polynomial identity. A local convergence is guaranteed without any extra condition. Integral action is incorporated into the adaptive controller to eliminate the steady-state error and to satisfy a condition of the unique solution for the polynomial identity. The control law used in this scheme is based on the set-point-on-I-only proportional-integral-derivative (PID) structure     

Parallel, self-organizing, hierarchical neural networks. II

For pt.I see IEEE Trans. Neural Networks, vol.1, p.167-78 (1990). Parallel, self-organizing, hierarchical neural networks (PSHNNs) involve a number of stages with error detection at the end of each stage, i.e., rejection of error-causing vectors, which are then fed into the next stage after a nonlinear transformation. The stages operate in parallel during testing. Statistical properties and the mechanisms of vector rejection of the PSHNN are discussed in comparison to the maximum likelihood method and the backpropagation network. The PSHNN is highly fault tolerant and robust against errors in the weight values due to the adjustment of the error detection bounds to compensate errors in the weight values. These properties are exploited to develop architectures for programmable implementations in which the programmable parts are reduced to on-off or bipolar switching operations for bulk computations and attenuators for pointwise operations     

A time-domain approach to transmission network equivalents viaProny analysis for electromagnetic transients analysis

This paper presents a method of obtaining transmission network equivalents from the network's response to a pulse excitation signal. The proposed method is based on modal decomposition representation for the large-scale interconnected system. In this framework we use Prony analysis to identify the network function of the system and to decompose the large system into a parallel combination of simple first-order systems. As a result the network function of the transmission network can be identified easily, and a Thevenin-type of discrete-time filter model can be generated. It can reproduce the driving-point impedance characteristic of the network. Furthermore, the proposed model can be implemented into the EMTP in a direct manner. The simulation results with the full system representation and the developed equivalent system showed a good agreement     

Strain analysis of moving objects using a Fourier transform grid method

There is no good method to measure the shape and the strain distributions of a structure changing with time. We have previously proposed the Fourier transform grid method (FTGM) to measure the three-dimensional shape and surface strain distributions of stationary objects by analysing the two-dimensional grating images recorded with two cameras. In the stereoscopic method, it is very important to determine the accurate geometric parameters of the camera system. In this paper, the positions and the directions of cameras are accurately determined using the FTGM applied to images of a reference object on which a two-dimensional grating is drawn. Applications for analysing shape and strain distributions of vibrating rubber plates and a moving human skin are shown.