Applications and Technologies of All-Solid State Blue Laser

1 Introduction Along with the matureness of laser diode (LD) manufacturing technology, the performance of LD has been improved greatly since 1980s, so various kinds of laser devices based on LD have been developed rapidly, especially the all-solid state lasers. After early experiments and researches, the all-solid state lasers have been commercialized successfully.     

高温预析出对Al-Zn-Mg系铝合金时效硬化和应力腐蚀的影响

研究了高温固溶后降温处理工艺对中强可使预析出LC52和7039铝合金的组织、时效硬化和应力腐蚀的影响。金相观察发现,高温预析出可优先在晶界处产生,并提高随后时效状态下晶界析出相的不连续分布程度,温度降低到一定程度晶内和晶界产生大量析出。合金拉伸性能和应力腐蚀结果表明,预析出在保持强度和塑性的同时,可提高抗应力腐蚀性能。而预析出温度降低,合金强度呈下降趋势。     

iShopFloor: an Internet-enabled agent-based intelligent shop floor

Global competition is driving manufacturing companies to change the way they do business. New kinds of shop floor control systems need to be implemented for these companies to respond quickly to changing shop floor environments and customer demands. This paper presents a new concept called iShopFloor-an intelligent shop floor based on the Internet, web, and agent technologies. It focuses on the implementation of distributed intelligence in the manufacturing shop floor. The proposed approach provides the framework for components of a complex control system to work together as a whole rather than as a disjoint set. It encompasses both information architecture and integration methodologies. The paper introduces the basic concept of iShopFloor, a generic system architecture, and system components. It also describes the implementation of eXtensible Markup Language message services in iShopFloor and the application of intelligent agents to distributed manufacturing scheduling. A prototype environment is presented, and some implementation issues are discussed.     

手工水饺定量给馅机的设计

手工水饺定量给馅机解决了包制手工水饺的定量给馅问题，保持每个水饺的重量一致稳定。该机采用柱塞泵给馅，气动传动，自动化，高效率，适合工业化生产手工水饺使用。     

镍氢电池负极用低成本储氢合金的研究

研究了ABS型储氢合金在低Co含量条件下，随B组元替代元素Co，Al，Si等含量的变化对合金电化学性能的影响规律，同时研究了A组元中不同La／Ce比对合金电化学性能的影响情况。结果表明，随合金中Co含量的降低，合金的活化性能和放电容量得以改善，但合金的循环寿命下降也比较明显；在试验范围内，随Al元素的加入，合金的循环寿命得以改善，但材料的放电容量和活化性能均有所下降；随合金La／Ce比的降低，合金的放电容量略有下降，但其循环寿命和放电电压平台有较大提高。     

High-Tc dc-SQUID magnetometer and its application in eddy current non-destructive evaluation

We have fabricated and tested a high-T_c dc-SQUID magnetometer patterned on a YBCO thin film deposited on a SrTiO₃ bicrystal substrate. The measurement of noise spectrum at 77 K showed that the magnetometer has a white noise of 333 fT/Hz^1/2 without superconducting shield, corresponding to a flux sensitivity of 14.5 μΦ₀/Hz^1/2. We constructed a test system for eddy current non-destructive evaluation of conducting aluminum plates by using the magnetometer. Flaws over 10 mm below the surface can be clearly identified. By mapping the magnetic field distribution, we can locate the flaw position. The signals caused by flaw were expanded due to the use of double-D type driving coil with a wider central slit. The experimental results confirmed that this test system could operate in a magnetic unshielded environment.     

片状陶瓷材料高低温电性能参数的自动检测

由进口电性能仪配上自制的高温系统，计算机自动采集数据，配置成一套高低温电性参数测定装置，该装置的特点是，升温快，炉体小巧，炉芯可更换盛液氮装置，屏蔽良好，等温区长，温工及参数测量精确可靠。