聚氨酯分散剂在液体靛蓝制备中的应用

采用异佛尔酮二异氰酸酯(IPDI)、聚乙二醇200、400、600、800(PEG200、PEG400、PEG600、PEG800)、2,2-二羟甲基丙酸(DMPA)、1-苯基-1,2-乙二醇、中和剂三乙胺(TEA)、甲乙酮肟等为原料,制备了一种阴离子聚氨酯分散剂.通过FTIR、GPC、TG表征了分散剂的结构与性能.利用自制的分散剂采用研磨法制备了液体靛蓝分散液,以液体靛蓝分散液粒径、离心稳定性、储存稳定性为指标,探讨了分散剂链长、用量对分散液性能的影响.结果表明,研磨1 h后,以PEG400为软段合成的聚氨酯分散剂用量为染料质量的60％时制备的液体靛蓝粒径为277.1 nm,1000 r/min离心稳定性达到93.98％,3000 r/min离心稳定性为51.13％,常温放置7 d后粒径变化在20 nm以内,染色后织物的颜色深度(K/S)为10左右,约是粉状靛蓝染色K/S的2倍,染色织物的颜色性能并未改变,SEM显示分散体颗粒大小分布均匀,与分散剂甲基萘磺酸钠的甲醛缩合物(MF)和木质素85A相比,其分散体系稳定性差别不大.     

太赫兹脉冲焦平面成像技术的发展与应用

作为太赫兹技术中的重要组成部分,太赫兹脉冲焦平面成像一经问世就引起了行业内的广泛关注,人们引入了各种方法去提升此成像技术的测量性能,同时也尝试将此成像技术应用于不同的工业和基础研究领域。本文综述了近年来人们对太赫兹脉冲焦平面成像的技术改良和应用研究,包括提升成像系统的空间分辨率、信噪比、信息获取能力,以及将此成像技术应用于光谱识别检测、超表面器件功能验证、太赫兹特殊光束测量、太赫兹表面波观测等,希望该综述能够推动太赫兹脉冲焦平面成像的进一步技术革新和应用拓展。     

Using decision analysis to determine optimal experimental design for monitoring sewer exfiltration with tracers.

The tracer methods developed to assess exfiltration from sewers in the European project APUSS (assessment of the performance of sewer systems) have a high degree of freedom with regard to the choice of tracer and the dosing strategy. These can lead to very different degrees of uncertainty in the measured exfiltration ratio. In this study, we demonstrate how to select an optimal experimental design using decision analysis, which accounts for this uncertainty and its associated costs. Although the results are site-specific, we can conclude generally that, when NaCl is used as the tracer, the accuracy of the exfiltration estimate is most sensitive to the amount of tracer used and the starting time of the experiment.     

One-dimensional GIS-based model compared with a two-dimensional model in urban floods simulation.

A GIS-based one-dimensional flood simulation model is presented and applied to the centre of the city of N?mes (Gard, France), for mapping flow depths or velocities in the streets network. The geometry of the one-dimensional elements is derived from the Digital Elevation Model (DEM). The flow is routed from one element to the next using the kinematic wave approximation. At the crossroads, the flows in the downstream branches are computed using a conceptual scheme. This scheme was previously designed to fit Y-shaped pipes junctions, and has been modified here to fit X-shaped crossroads. The results were compared with the results of a two-dimensional hydrodynamic model based on the full shallow water equations. The comparison shows that good agreements can be found in the steepest streets of the study zone, but differences may be important in the other streets. Some reasons that can explain the differences between the two models are given and some research possibilities are proposed.     

Control of reactive distillation production of high-purity isopropanol

The process characteristics and control strategy of a high-purity IPA reactive distillation column were investigated. A robust nominal operation was found by maintaining an excess of propylene feed to the column and recycling the unreacted propylene to the feed instead of the top stage. Stage temperature and propylene composition with one-to-one relationship with reboiler duty and propylene feed are selected as controlled variables for maintaining bottom purity and feed ratio in the presence of possible measurement bias respectively. High nonlinearity between selected input–output pair was reduced by using variable transformation. Dynamic simulations demonstrated that such a control scheme with nonlinear transformed variable was capable of providing much superior control performance than the one using natural variable.     

On the problem of hydrogen removal during heat treatment of large forgings

The solutions to a differential equation for the problem of heating of a cylinder in a medium with a fixed temperature are used to obtain equations for estimating the change in the hydrogen concentration in forgings from data on the hydrogen concentration at the cylinder axis or on the average bulk hydrogen concentration. Similar equations are also obtained for forgings having square cross sections. The calculation demonstrates that, for the case of a twofold decrease in the hydrogen concentration in a forging, the calculated times of annealing of a cylindrical forging differ by three times.     

On a New Method for H2 -Based Decomposition

This note proposes a simple linear matrix inequality (LMI) system for the design of static precompensators to reduce the interactions of a multivariable system. The approach is based on minimizing the H₂ norm of a modified system and the LMIs are derived from the well known technique of pseudodiagonalisation. The approach is applied to two complex real-life benchmark problems with high levels of interaction. It is shown that its performance is significantly better than previously proposed LMI optimization techniques for designing static precompensators     

An element-based displacement preconditioner for linear elasticity problems

Finite element analysis of problems in structural and geotechnical engineering results in linear systems where the unknowns are displacements and rotations at nodes. Although the solution of these systems can be carried out using either direct or iterative methods, in practice the matrices involved are usually very large and sparse (particularly for 3D problems) so an iterative approach is often advantageous in terms of both computational time and memory requirements. This memory saving can be further enhanced if the method used does not require assembly of the full coefficient matrix during the solution procedure. One disadvantage of iterative methods is the need to apply preconditioning to improve convergence. In this paper, we review a range of established element-based preconditioning methods for linear elastic problems and compare their performance with a new method based on preconditioning with element displacement components. This new method appears to offer a significant improvement in performance.