合成己二腈反应技术研究——(Ⅴ)己二腈工业反应过程模拟与反应器改造

对己二腈工业反应器提出了两釜串联带回流的模型,通过模拟计算得出模型的级间返混系数 f=6的结论。该模型能较好地预测工业反应器中物料组分浓度变化和气、液两相的流动特性;指出了现工业反应器的鼓泡中和段体积偏小是造成己二酸浓度偏高的关键;提出了可以通过增加串连一个鼓泡预反应段的改造方案,能有效地降低己二酸的浓度,从7%降至4%左右,从而能较好地减缓腐蚀和结焦。     

A concise process technology for 3-D suspended radio frequency micro-inductors on silicon substrate

In this letter, a concise process technology is proposed for the first time to enable the fabrication of good quality three-dimensional (3-D) suspended radio frequency (RF) micro-inductors on bulk silicon, without utilizing the lithography process on sidewall and trench-bottom patterning. Samples were fabricated to demonstrate the applicability of the proposed process technology.     

Study of 18-cm long single-sided AC-coupled silicon microstripdetectors

The SSC GEM silicon Central Tracker design incorporated 18-cm long single-sided AC-coupled silicon microstrip ladders. Compared to the 12-cm long ladders considered in the preliminary stages of the tracker design, the 18-cm long ladders have the advantage of reduced cost, channel count and overall power consumption, and led to a simplified tracker assembly. However, such long ships also present the challenge of maintaining satisfactory performance. The increased capacitance and series resistance contribute to lower signal-to-noise ratios, longer time walk, higher power consumption per channel and increased probability of crosstalk to neighboring channels. In this paper, an accurate method to calculate the geometric capacitance of the AC-coupled microstrips is presented and the calculated results are compared with measurements, SPICE simulations are performed to predict the noise, the extent of interstrip capacitive coupling and the dispersion of the detector signal due to the finite series resistance of the metal strips and the long length of the detector. The influence of the preamplifier current and the shaping time on the signal and noise levels is also presented. The study concludes that the 18-cm long ladders can successfully satisfy the performance goals of the GEM silicon Central Tracker     

显影液QA,QC的科学方法

本文为自动洗片机用高温快速显影液的科学管理与质量保证提供了简便、科学的检测方法,力医(?)影像质量的提高提供了可靠的保证。具有科学性、实用性、普及性。     

铝液夹杂物检测DMIRT－Ⅲ法的试验研究

提出了一种新的铝液夹杂物快速检测方法。导出了该法的检测原理方程。分析并试验研究了影响检测重复性和分辨率的因素。试验选择了较好的检测参数，并获得了较好的检测结果。     

Simulation study of peak junction temperature and power limitationof AlGaAs/GaAs HBTs under pulsed and CW operation

The authors have used a 3-D transmission-line matrix (TLM) modeling method to study the junction temperature distribution and power limitation of device geometries with multiple embedded heat sources. Peak values of the junction temperature against the dissipated power density under both pulsed and CW operation are presented for a typical power AlGaAs/GaAs HBT structure. These data should facilitate the rapid determination of junction temperature for a given output power, which is of paramount importance in power device design     

Eigenvalue-based algorithms for testing positive realness of SISO systems

A computational test for scalar positive real and strictly positive real functions is proposed in this paper. The input for this algorithm is state space representation, not necessarily minimal. It is derived for the discrete time problem, based on numerical stable eigenvalue computations. The test can be used in the continuous counterpart, which is in fact an improvement of an algorithm posed by Bai and Freund. Differences between the discrete and continuous time problems are also pointed out.     

A dynamic programming method for analysis of bridges under multiple moving loads

A dynamic programming (DP) method is presented for analysis of statically determinate and indeterminate bridges subjected to moving loads such as those specified by the American Association of State Highway and Transportation Officials (AASHTO) specifications. These loads consist of uniform lane loading, two-axle truck loading and two-axle truck plus one-axle semitrailer loading. The solution of the DP problem is based on the use of influence line diagrams and extremum functions. Recurrence formulae have been developed for various types of AASHTO live loads. The procedure presented in this article is quite general and can be applied to any type of structures with linear behaviour and any type of moving loads. Six examples are presented: a simply-supported beam, a simply-supported Pratt truss, an arch bridge, a continuous Pratt truss, a continuous frame and a cable-stayed bridge.     

由呼出气中的氡浓度估计铀矿工体内~(225)Ra的负荷量

本文测量了某铀矿不同工种的56名矿工下矿井作业前的呼出气中的~(222)Rn浓度,并由此估算了他们体内的~(226)Ra 负荷量。按不同工种的人数加权,呼出气中的~(222)Rn 浓度平均值为34.1Bqm~(-3),体内~(226)Ra 负荷量的均值为1.95kBq。同时还对9名休息了2天的和2名离开井下作业3—4年的矿工以及12名来下过矿井的本矿工人呼出气中氡浓度进行了测量,由此估算出其体内~(226)Ra 负荷量的均值分别为1.11、0.94和0.17kBq。