吸湿凉爽机织物的结构设计与性能

为研究织物组织结构与复合纱线线密度对织物凉爽性能的影响,将线密度为7.4和9.8 tex涤纶分别与线密度为7.8 tex锦纶反向加捻、并线后作为纬纱,以8.3 tex涤纶/竹浆纤维50/50混纺纱作经纱,设计平纹、二上一下斜纹和透孔组织织物.测试织物的瞬间接触凉感、热湿舒适性能及织物干、湿态升温曲线,并采用凉爽温度指数对织物的综合凉爽性能进行评价.研究结果表明:6种设计织物的瞬间接触凉感均高于标准,且平纹织物最好,纬纱粗细对瞬间接触凉感影响不显著;透孔织物透气性最好,且在人体出汗的状态下具有较好的导湿散热性能.平纹织物凉爽温度指数最高,最大凉爽温度为2.8℃,综合凉爽性能最好.     

Kinetics of two-step anionic polymerization

This article deals with the kinetics of two-step anionic polymerization by way of a non-steady state method. Several molecular parameters can be evaluated using the formulae developed. A bimodal molecular weight distribution function for the resulting polymer is derived from the set of kinetic differential equations, which is in agreement with the experimental data reported.     

Electrical properties and positron annihilation study of (Ba<Subscript>1−<Emphasis Type="Italic">x</Emphasis></Subscript>Ho<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript>)TiO<Subscript>3</Subscript> ceramics

DC resistivity, dielectric constant, dielectric loss and positron annihilation spectra of (Ba_1−x Ho _x )TiO₃ ceramics have been measured as a function of holmium concentration x. It has been found that the DC resistivity of (Ba_1−x Ho _x )TiO₃ is strongly dependent on the Ho content: it decreases three orders of magnitude and reaches a minimum at x = 0.4%. Doping with 0.6% holmium increases the permittivity of BaTiO₃ by approximately three times (from ∼1,300 to ∼4,000), with only a slight increase in the corresponding dielectric loss. The local electron density and defect concentration estimated using positron annihilation technique conforms well to the features found in the dielectric and resistivity measurements. The results have been discussed in terms of a mixed compensation model.     

Modeling Power Supply Noise in Delay Testing

Excessive power supply noise during test can cause overkill. This article discusses two models for supply noise in delay testing and their application to test compaction. The proposed noise models avoid complicated power network analysis, making them much faster than existing power noise analysis tools. can cause performance degradation and     

Fuel management of the HTR-10 including the equilibrium state and the running-in phase

The mode of fuel management of the HTR-10 was studied, including the simulation of the fuel shuffling process and the measurement of the burnup of a fuel element. The prior consideration was the design of the equilibrium state. Based on this the fuel loading of the initial core and the fuel shuffling mode from the initial core through the running-in phase into the equilibrium state were studied. The code system VSOP was used for the physical layout of the HTR-10 at the equilibrium state and in the running-in phase. For the equilibrium state, in order to lessen the difference between the peak and the average burnup, 5-fuel-passage-through-the-core was chosen for the fuel management. The average burnup of the spent fuel for the equilibrium core is 80 000 MWd t⁻¹, and the peak value of it is less than 100 000 MWd t⁻¹ when the burnup of the recycled fuel element is under 72 000 MWd t⁻¹. The mixture of fuel element and graphite element was used for the initial core loading, the volume fractions of the fuel and the graphite elements were 0.57 and 0.43, respectively. During the running-in phase, the volume fraction of graphite will decrease with the fresh fuel elements being loaded from the top of the core and the graphite elements discharged from the bottom of the core. The fuel shuffling mode is similar to that of the equilibrium state. The burnup limit of recycled fuel element is also 72 000 MWd t⁻¹ and the peak burnup is less than 100 000 MWd t⁻¹. Finally the core will be full of fuel elements with a certain profile of burnup and reaches the equilibrium state. According to the characteristics of the pebble-bed high temperature gas-cooled reactor, a calibrating method of concentration of ¹³⁷Cs was proposed for the measurement of fuel burnup.     

焊接史

本文追溯了19世纪末发明的电弧焊接的历史。当Oscar Kjellberg成立伊萨公司以探索他发明的涂层焊条时，伊萨从一开始就和电弧焊的发展结下了不解之缘。     

Surface charge accumulation and decay on a spacer stressed with DC voltages at atmospheric conditions

Contents Surface charge accumulation and its decay at a GIS spacer are studied at atmospheric conditions employing a two step-calibration method. The results show that the accumulation saturates within 30 minutes; the dominant mechanism of surface charge accumulation is the drift of charged particles via air, while that of the decay is surface conduction. The characteristics are similar at both polarities.

---

Sättigungskonzentration und Abklingverhalten der Oberflächenladung an einem mit Gleichspannung beanspruchten Abstandshalter unter atmosphärischen Bedingungen

Übersicht Die Konzentration und das Abklingen von Oberflächenladungen an einem GIS Abstandshalter wurden unter atmosphärischen Bedingungen mit Hilfe eines zweistufigen Kalibrierungsverfahrens untersucht. Die Ergebnisse zeigen eine Sättigung der Ladungskonzentration innerhalb von 30 Minuten. Als Hauptursache der Ladungskonzentration ist die Drift geladener Teilchen in Luft anzusehen, während das Abklingen auf die Oberflächenleitung zurückzuführen ist. Ähnliche Charakteristiken ergeben sich mit beiden Polaritäten.

     

CdSe量子点的制备与荧光特性研究

主要讨论了CdSe量子点的制备及荧光特性。CdSe量子点由化学方法制备，通过选择不同的反应时间得到不同尺度的量子点样品。用荧光方法研究了量子点样品在石英衬底和有机溶剂中的荧光特性。实验表明，这些量子点都有良好的荧光特性。还用无限深球方势阱模型分析了量子点样品的电子态，并根据荧光参数估算了量子点的尺度．各样品荧光峰具有一致的半峰宽，表明CdSe量子点的成核过程在反应开始时同时完成。     

沉默的文化——妇女的住房和土地权利

我们即将对第四届妇女大会（北京）召开十年以来的妇女发展状况进行回顾，并且要对千年发展目标的执行情况进行中期评估。因此，我们有必要对那些影响妇女日常生活的关键问题进行审视并采取相应的行动，这些问题一直被各国政府和国际社会所忽视。