Theoretical and Experimental Study of Water Transport in a Hollow Cylinder Applied to the Drying of Round Squid Mantle

Until now, attention has been focused solely in the drying of squid mantle from an experimental point of view, neglecting the transport phenomenon studies of water in squid muscle. This work studies the drying of squid mantle (Loligo brasiliensis), previously salted and smoked by liquid smoking (hickory extract), using a tubular dryer in closed cycle with a silicagel fixed bed in series. The mass transfer phenomenon during drying was studied, based on the Fick's second law, with the effective diffusivity supposed constant, which enabled an analytical solution to the problem. The drying curve calculated with the resulting equation was compared with experimental data. The model was applied to a hollow cylinder geometry (round squid mantle), with its internal surface isolated from the drying environment by a plastic film. The latter was given a tubular form and introduced inside the mantle cavity (impervious wall boundary condition).     

A sensorless brushless dc motor system

This paper describes a brushless dc motor system without position or speed sensor. The brushless motor consists of a permanent magnet synchronous motor and a voltage-source inverter capable of controlling the amplitude and frequency of voltage. The rectangular-shaped stator current with a conducting interval of 120° (electrical) is controlled to be in phase with the trapezoidal back electromotive force. This results in producing maximum torque. Variable speed is achieved by adjusting the average motor voltage similarly to chopper control of dc motors. In this paper, two sensorless position detecting methods, i.e., an “indirect method” suited for the lower-speed range and a “direct method” suited for the higher-speed range are proposed. The combination of the two makes it possible to detect the rotor position over a wide-speed range. Furthermore, a speed-sen-sorless PLL control is proposed in applying the principle of the direct method. Experimental results obtained from a prototype brushless dc motor are shown to confirm the validity of the sensorless drive. The starting procedure of the motor also is discussed because it is impossible to detect the rotor position at a standstill.     

The As-prepared surfaces of C-axis-oriented Nd1Ba2Cu3Oy thin films characterized using scanning probe microscopes

Recently, superconducting Nd₁Ba₂Cu₃O_y (Ndl23) thin films with high superconducting transition temperature (T _c) have been successfully fabricated at our institute employing the standard laser ablation method. In this paper, we report the results of surface characterization of the Nd123 thin films using an ultrahigh vacuum scanning tunneling microscope/spectroscopy (UHV-STM/STS) and an atomic force microscope (AFM) system operated in air. Clear spiral pattern is observed on the surfaces of Nd123 thin films by STM and AFM, suggesting that films are formed by two-dimensional island growth mode. Contour plots of the spirals show that the step heights of the spirals are not always the integer or half-integer number of thec-axis parameter of the structure. This implies that the surface natural termination layer of the films may not be unique. This result is supported byI-V STS measurements. The surface morphology of the Nd123 thin films is compared with that of thec-axis-oriented Y₁Ba₂Cu₃S_y thin films. Surface atomic images of the as-prepared Nd123 thin films are obtained employing both STM and AFM. STS measurements show that most of the surfaces are semiconductive. The results of STS measurements together with the fact that we are able to see the surface atomic images using scanning probe microscopes suggest that exposure to air does not cause serious degradation to the as-prepared surfaces of Nd123 thin films.     

Wavelength-selective fused fiber couplers utilizing fielddifference between core and cladding modes

It is shown that wavelength-selective fused taper couplers can be made by using the large difference in field distribution, between core and cladding modes. It is evident from the calculation results that fibers with a high-index difference and a thin outside diameter are necessary to fabricate the couplers. Fused taper couplers are made of thin fibers with a cladding diameter of 66.0 μm and an index difference of 0.84%. The splitting ratio of the coupler obtained is more than 20 dB in the 1.53-μm region and less than -20 dB in the 0.8 to 1.0-μm region. The loss is less than 0.2 dB and 0.4 dB in the 1.53-μm and the 0.8 to 1.0-μm regions, respectively     

Properties of aqueous solutions of several salts of α,ω-alkanediol disulfates

Several salts of α,ω-sulfates, MO₃SO(CH₂)_n OSO₃M(n=12, 14, 16, 18, and M=Li, Na, and K) were prepared from the corresponding α,ω-alkane diols. The Krafft points of these α,ω-sulfates with common counterion as estimated by electroconductivity measurements increased with the increase of the hydrocarbon chain length, and the effect of the counterions on the Krafft points of the α,ω-sulfates with the same hydrocarbon chain length was in the order : Li<Na<K. Solutions of the α,ω-sulfates, except disodium dodecanediol disulfate, showed two break points corresponding to the first and second critical micelle concentration in each plot of the electroconductivity as a function of the concentration. The existence of the second break point suggested that another aggregation of rearrangement of the existing aggregates occurs in α,ω-sulfate solutions in addition to the usual micelle formation. The first and second break points of α,ω-sulfates with sodium counterion decreased logarithmically with increasing total number of methylene groups. The relationships were given as follows: log(first break point)=−0.138Nc−0.095; log(second break point)=−0.104Nc−0.251. The effect of the counterions upon the break points of α,ω-sulfates with the same hydrocarbon chain length was in accordance with their positions in the lyotropic series.     

Dynamic moduli for short fiber-CR composites

The dynamic moduli, E′ and E″, and tan δ for nylon–CR and PET–CR composites with unidirectional short fibers were studied as a function of temperature by using a Rheovibron. The temperature dependence of tan δ showed two dispersion peaks for nylon–CR composite. The peak at ?28°C corresponded to the main dispersion of CR and the peak at 100°C to the α-dispersion of nylon 6. For a PET-CR composite, in addition to the individual dispersion of CR and PET, a small and broad peak was observed at about 90°C. The angular dependence of E′ indicated that the short fibers assumed good orientation. The storage modulus for the composites was given by the parallel model as E′ = V_f′E_f + V_mE′_m., where E′_c, E′_f and E′_m were the storage modulus for the composite, fiber, and matrix and V_f and V_m were the volume fraction of fiber and matrix, respectively. In the transverse direction of fiber, the peak values of tan δ at ?28°C were given by the following equation; tan δ_c = tan δ_m ? δV_f, where tan δ_c and tan δ_m are the loss tangent for the composite and matrix, respectively, and α is coefficient depending on fiber type. The results indicated that a region with strong interaction was formed between fibers and CR matrix.     

New method for selective growth of diamonds by microwave plasma chemical vapour deposition

Selective nucleation and deposition of diamonds were achieved on an SiO₂-patterned Si substrate. The substrate was pre-treated with an electric field in plasma to introduce diamond nuclei. This treatment did not affect the SiO₂ area. Consequently, diamonds grew only on the area where Si was exposed under the conventional conditions of diamond growth. The maximum nucleation density on the area of SiO₂was about 5 × 10⁷ cm⁻². The ratio of the selectivity was 2 × 10² or higher. This process will be useful and very promising for manufacturing diamond electronic devices.     

Tribological Characteristics of SiC Ceramics in High-Temperature and High-Pressure Water

The effects of temperature and sliding speed on the tribological behavior of a SiC ceramic by sliding on the same material in deoxygenated water were investigated from room temperature to 300°C under the corresponding saturated vapor pressures. The friction coefficient and specific wear rates of both plates and disks increased at elevated temperatures at all sliding speeds, but decreased with increasing sliding speed at 120° and 300°C. Fine mirrorlike worn surfaces were observed without wear debris under all sliding conditions. The wear mechanism appears to consist of hydrothermal oxidation of SiC and dissolution of reaction products such as silica.     

Hydrophobic effects on protein/nucleic acid interaction: enhancement of substrate binding by mutating tyrosine 45 to tryptophan in ribonuclease Tl

Hydrophobic effects on binding of ribonuclease Tl to guaninebases of several ribonucleotides have been proved by mutatinga hydrophobic residue at the recognition site and by measuringthe effect on binding. Mutation of a hydrophobic surface residueto a more hydrophobic residue (Tyr45 – Trp) enhances thebinding to ribonucleotides, including mononucleotide inhibitorand product, and a synthetic substrate-analog trinudeotide aswell as the binding to dinucleotide substrates and RNA. Enhancementson binding to non-substrate ribonucleotides by the mutationhave been observed with free energy changes ranging from –2.2 to – 3 .9 kJ/mol. These changes are in good agreementwith that of substrate binding, –2.3 kJ/mol, which iscalculated from Michaelis constants obtained from kinetic studies.It is shown, by comparing the observed and calculated changesin binding free energy with differences in the observed transferfree energy changes of the amino acid side chains from organicsolvents to water, that the enhancement observed on guaninebinding comes from the difference in the hydrophobic effectsof the side chains of tyrosine and tryptophan. Furthermore,a linear relationship between nucleolytic activities and hydrophobicityof the residues (Ala, Phe, Tyr, Trp) at position 45 is observed.The mutation could not change substantially the base specificityof RNase Tl, which exhibits a prime requirement for guaninebases of substrates.     

Elevated Alpha 1(I) to Alpha 2(I) Collagen Ratio in Dermal Fibroblasts Possibly Contributes to Fibrosis in Systemic Sclerosis

Systemic sclerosis (SSc) is characterized by excessive collagen deposition in the skin and internal organs. Activated fibroblasts are the key effector cells for the overproduction of type I collagen, which comprises the α1(I) and α2(I) chains encoded by COL1A1 and COL1A2, respectively. In this study, we examined the expression patterns of α1(I) and α2(I) collagen in SSc fibroblasts, as well as their co-regulation with each other. The relative expression ratio of COL1A1 to COL1A2 in SSc fibroblasts was significantly higher than that in control fibroblasts. The same result was observed for type I collagen protein levels, indicating that α2(I) collagen is more elevated than α2(I) collagen. Inhibition or overexpression of α1(I) collagen in control fibroblasts affected the α2(I) collagen levels, suggesting that α1(I) collagen might act as an upstream regulator of α2(I) collagen. The local injection of COL1A1 small interfering RNA in a bleomycin-induced SSc mouse model was found to attenuate skin fibrosis. Overall, our data indicate that α2(I) collagen is a potent regulator of type I collagen in SSc; further investigations of the overall regulatory mechanisms of type I collagen may help understand the aberrant collagen metabolism in SSc.