Transmittance and cathodoluminescence of AlN ceramics sintered with Ca3Al2O6 as sintering additive

Aluminum nitride ceramics were prepared by sintering with 0–4.8 mass% of Ca₃Al₂O₆ (C₃A) as a sintering additive. The transmittance in the range of 260–550 nm increased with increasing amount of C₃A. The cathodoluminescence intensity attributed to oxygen-induced defects decreased with increasing amount of C₃A. From the results, the increase of the transmittance in the range of 260–550 nm was considered to be related to the decrease of the oxygen-induced defect density.     

Formation of toxic aldehydes in cod liver oil after ultraviolet irradiation

Formaldehyde, acrolein, malonaldehyde (MA), acetaldehyde and propanal produced from cod liver oil upon ultraviolet irradiation (λ_max=300 nm) were derivatized into nitrogenor sulfur-containing compounds and then analyzed by capillary gas chromatography with a nitrogen-phosphorus detector or a flame photometric detector. Acrolein and MA were formed at levels of 10.9±3.06 and 190.2±38.4 nmol/mg of fish oil, respectively. Maximum levels of formaldehyde, acetaldehyde and propanal formed were 7.0±0.90, 49.1±4.5 and 35.8±4.0 nmol/mg of oil, respectively. Formation of propanal in large quantities corresponded to the high content of ɛ-3 fatty acids in cod liver oil.     

A new type of arc plasma reactor with 12-phase alternating current discharge for synthesis of carbon nanotubes

A new type of arc plasma reactor with 12-phase alternating current (AC) discharge for synthesis of carbon nanotubes (CNTs) is proposed. A couple of six discharge electrodes by which have mutually electrical connection between them to enlarge the high-temperature regions in the reactor are arranged to three-dimensional locations. A new method of CNTs fabrication by this reactor, which accomplishes to enlarge the suitable growth region in high purity and at high yield, was developed.     

Generation of adaptive gait patterns for quadruped robot with CPG network including motor dynamic model

This paper describes the generation of adaptive gait patterns using new Central Pattern Generators (CPGs) including motor dynamic models for a quadruped robot under various environments. The CPGs act as the flexible oscillators of the joints and adjust joint angles to required values. The CPGs are interconnected with each other and sets of their coupling parameters are adjusted by a genetic algorithm so that the quadruped robot can realize stable and adequate gait patterns. Generation of gait patterns results in the formation of the CPG networks suitable for the formation of not only a straight walking pattern but also of rotating gait patterns. Experimental results demonstrate that the proposed CPG networks are effective for the automatic adjustment of the adaptive gait patterns for the tested quadruped robot under various environments. Furthermore, the target tracking control based on image processing is achieved by combining the general gait patterns. © 2006 Wiley Periodicals, Inc. Electr Eng Jpn, 155(1): 35–43, 2006; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20225     

Stress intensity factors of microstructurally small crack

The stress intensity factor (SIF) is widely used for evaluating integrity of cracked components. Averaging the anisotropy of each crystal, the macroscopic behavior of polycrystalline materials is isotropic and homogenous in terms of elastic deformation. However, the anisotropic and/or inhomogeneous property influences on the stress field around a crack if the crack size is small in comparison with the grain. Thus, the SIF of the microstructurally small crack may differ from that in the isotropic body. In present study, the effect of anisotropic/inhomogeneous elasticity on the SIF is investigated by using the finite element analysis (FEA). At first, the SIFs of semi-circular crack in a single crystal and a polycrystalline material are calculated. These reveal that the magnitude of SIF is dependent not only on the crystal orientation but also on the deformation constraint by the neighboring crystals. Then, the statistical scatter of SIF due to the random orientation of crystal orientation in a polycrystal is examined by a Monte Carlo simulation.     

Taxonomy for protective ability of rust layer using its composition formed on weathering steel bridge

For a quantitative evaluation of the protectiveness of a rust layer formed on a weathering steel bridge, the relationship between the corrosion rate of the bridge and the composition of the rust layers formed on the girders was first investigated. These corrosion rates were clearly classified by the protective ability index (PAI) of α/γ^∗ and (β + s)/γ^∗, where α, γ^∗, β and s are the mass ratio of crystalline α-FeOOH, the total of γ-FeOOH, β-FeOOH and the spinel-type iron oxide (mainly Fe₃O₄), β-FeOOH and spinel-type iron oxide, analyzed by XRD, respectively. The inequality of the former index α/γ^∗ > 1 expressed the protectiveness criterion of the rust layer, while that of the latter index, (β + s)/γ^∗< 0.5 or > 0.5, classified the corrosion rate of the non-protective rust layer. The PAI is useful for a quantitative evaluation of the protectiveness of a rust layer formed on a weathering steel bridge and is an important item for the corrosion assessment of the bridge.     

Preparation of water‐repellent silks by a reaction with octadecenylsuccinic anhydride

Silk fibers and membranes were acylated with octadecenylsuccinic anhydride (ODSA) at 75°C for different times. Swelling [N,N‐dimethylformamide (DMF) and dimethyl sulfoxide (DMSO)] and nonswelling (xylene) solvent media were used for the reaction. Silk membranes that reacted in DMF or DMSO displayed faster reaction kinetics and attained higher weight‐gain values than fibers. The effect of the solvent on the reaction yield was in the following order: DMSO > DMF ? xylene. The Fourier transform infrared spectra of acylated silk samples showed the characteristic absorption bands of the anhydride at 2990, 2852, 1780–1700, and 1170 cm^?1. The intensity of the latter band, which increased linearly with the weight gain, was used as a marker for evaluating the reaction kinetics of the samples acylated in the nonswelling medium. The moisture regain and water retention of silk fibers acylated with ODSA decreased significantly, regardless of the solvent system used. Accordingly, the water repellency increased. Acylation induced an increase in the thermal stability of the silk fibers and membranes. Fine particles adhering to the surfaces of the silk fibers acylated in xylene were detected by scanning electron microscopy. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 324–332, 2003     

Poly(butylene succinate)/poly(vinyl phenol) blends. Part 1. Miscibility and crystallization

Miscibility has been investigated in blends of poly(butylene succinate) (PBSU) and poly(vinyl phenol) (PVPh) by differential scanning calorimetry in this work. PBSU is miscible with PVPh as shown by the existence of single composition dependent glass transition temperature over the entire composition range. In addition, the polymer–polymer interaction parameter, obtained from the melting depression of PBSU using the Nishi–Wang equation, is composition dependent, and its value is always negative. This indicates that PBSU/PVPh blends are thermodynamically miscible in the melt. Preliminary morphology study of PBSU/PVPh blends was also studied by optical microscopy (OM). OM experiments show the spherulites of PBSU become larger with the PVPh content, indicative of a decrease in the nucleation density, and the coarseness of PBSU spherulites increases too with increasing the PVPh content in the blends.     

高速气流冲击式粉体表面改性装置——HYBRIDIZATION系统及应用

利用高速气流冲击法进行粉体/粉体系表面改性技术,是迄今为止各种粉体材料开发中最为引人注目的技术之一。HYBRIDIZATION(下称HYB)系统是利用高速气流冲击法对微粉体进行干式/机械化处理,是使材料复合化的最实用的装置,可对各类有机物、无机物、金属等进行广泛组合,通用性很强,适用于许多行业领域。从本文所述的系统构成、型式,有关的典型球形化处理的运转特性,利用复合化高温粉体测定被处理粉体表面温度,利用颜料改变色调等的处理特点及该系统的适用性等(一部分是从已发表的学术论文及专利上摘录的),可以说明HYB系统的概况。