Flashover voltage characteristics of contaminated station insulators under temporary ac overvoltages in the ac system connected with a frequency converter station

According to the recent analysis results of temporary ac overvoltage in the ac system connected with a frequency converter station, large-magnitude over-voltages were confirmed to occur under some special system conditions. Most of the station insulators currently used cannot withstand such overvoltages according to an evaluation based on the data obtained earlier. The necessity of tests to be done to evaluate such performance more accurately was recognized. Both power frequency and switching impulse overvoltage flashover tests were made on contaminated insulators by the method well simulating the natural wetting condition. Switching impulse flashover voltage with the waveshape having a long wavefront time of 2 ms can be well correlated with the flashover voltage characteristics of temporary ac overvoltage. Higher flashover voltage characteristics were obtained by a clean fog test method compared with those obtained by equivalent fog test method.     

Radiative ignition mechanism of solid fuels

Transmittance of external radiation from a CO₂ laser through a boundary layer of decomposition products over a vertical sample surface is measured during the ignition period. The results indicate that there is significant absorption of the external radiation for PMMA, and a lesser but still not negligible amount, for red oak. An increase in gas phase temperature over surface temperature is observed over much of the ignition interval. Using the experimentally measured incident flux at the sample surface, surface temperature history was calculated from a model that included re-radiation and convection losses from the surface, endothermic decomposition and conduction into the material. The results confirm the significant effect of gas phase absorption on surface temperature. Steady-state-derived surface regression rate expression was used for PMMA in this model. The results raise questions about the validity of such data for the dynamic heating conditions during the ignition period. Further studies needed to understand the radiative ignition mechanism are identified.     

Solid-Phase Syntheses of Two Deacetyl-Thymosin β4 Analogues with Substitution at Position 12 and Their Effects on Impaired Blastogenic Response of T Lymphocytes of Uremic Patients

Two deacetyl-thymosin β₄ analogues containing Phe(4Br) or D-Phe(4Br) as position 12 were synthesized by the manual solid-phase method, and their immunological effects on the impaired blastogenic response of phytohemagglutinin-stimulated T lymphocytes of uremic patients with infectious diseases were studied. Bromination of the p-position of Phe¹² resulted in a marked restorative effect on the impaired blastogenic response of T lympocytes compared with that of our synthetic deacetyl-thymosin β₄ The synthetic [Phe(4Br)¹²]deacetyl-thymsin β₄ was approximately equal in potency to our synthetic [Phe(4F)¹²]deacetyl-thymosin β₄ in uremic patients, but the other analogue, [D-Phe(4Br)¹²]deacetyl-thymosin β₄, had no effect.     

Generation of adaptive gait patterns for quadruped robot with CPG network including motor dynamic model

This paper describes the generation of adaptive gait patterns using new Central Pattern Generators (CPGs) including motor dynamic models for a quadruped robot under various environments. The CPGs act as the flexible oscillators of the joints and adjust joint angles to required values. The CPGs are interconnected with each other and sets of their coupling parameters are adjusted by a genetic algorithm so that the quadruped robot can realize stable and adequate gait patterns. Generation of gait patterns results in the formation of the CPG networks suitable for the formation of not only a straight walking pattern but also of rotating gait patterns. Experimental results demonstrate that the proposed CPG networks are effective for the automatic adjustment of the adaptive gait patterns for the tested quadruped robot under various environments. Furthermore, the target tracking control based on image processing is achieved by combining the general gait patterns. © 2006 Wiley Periodicals, Inc. Electr Eng Jpn, 155(1): 35–43, 2006; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20225     

Development of cable fault location method using fiber optic distributed temperature sensor

When ground-fault problems occur on a cable line, immediate fault location and restoration are required. Therefore, various new methods to locate the fault point instantaneously have been investigated to replace such conventional methods as the Murray loop method and the pulse radar method [1]. These methods require a long time to locate the fault point. One possible fault location method is to sense the temperature rise following a ground fault using a fiber optic distributed temperature sensor. Application of this method was found feasible through sensing the temperature rise at a ground-fault test using a thermocouple as a temperature sensor with test cables [4]. A power/optical composite cable was prepared experimentally and after verifying its thermal mechanical performance, the temperature rise at an incidence of a fault was determined and the anticipated performance was demonstrated in a ground-fault test. This article describes the outline of the test.     

Some experimental findings in compression-after-impact (CAI) tests of CF/PEEK (APC-2) and conventional CF/epoxy flat plates

Compression-after-impact (CAI) tests have been conducted for quasi-isotropic thick plates with 48 plies by using the NASA method and on plates with 32 plies by using the SACMA method. Specimens are made of CF/PEEK (APC-2) and conventional CF/epoxy for the NASA plates and CF/epoxy for the SACMA plates. In the NASA CAI tests, the sequence of delamination buckling and its propagation is clearly revealed through various experimental techniques. One major technique is moiré topography, and the other is thermo-mechanical stress analysis with a high-accuracy infrared sensor. The arrest of delamination propagation just before catastrophic failure due to high fracture toughness is clearly captured by the moiré camera. This behavior provides good CAI values of CF/PEEK. The initial buckling properties of the delaminated region by the impact are then extensively discussed. Numerical predictions of initial buckling stress have been obtained by modelled geometry of the delaminated region simplified from its precise structure clarified by ultrasonic C-scanning. They agree fairly well with the experimental results. The in-plane stress distribution in the delaminated region before initial buckling is measured by an infrared stress graphic system. This compared favorably with finite element predictions. Two types of symmetric buckling modes with respect to the central plate surface, twin and single peak ones, are experimentally captured.     

The cause of the uneven carbonization process in wet coal charging in coke oven chamber

In the case of the wet coal charging process in coke oven chamber, it is known that the coking process is uneven and a local carbonization delay occurs. The reason was investigated through a laboratory-scale experiment and a quantitative estimation. A partial carbonization test in a test coke oven replicated the uneven plastic layer and local carbonization delay. It was revealed that most of the gas generated in the uncarbonized coal layer results from the evaporation of condensed water and that steam can break through the plastic layer in a test coke oven. Moreover, the order estimation implied that steam that generates in the uncarbonized coal layer and breaks through the plastic layer has sufficient heat capacity to cool the heating wall and delay the carbonization. It was also shown that the steam pressure peak measured in a commercial coke oven is much lower than the estimated steam pressure in this study assuming steam not breaking through the plastic layer. The above-mentioned results and quantitative investigation strongly support the ‘steam breaking through the plastic layer’ theory proposed by Dr. Rohde that an uneven carbonization process is caused by vaporized coal moisture breaking through the plastic layer at definite, unforeseeable points, which results in cooling of the wall by the steam flow.     

NiCoFe/C cathode electrocatalysts for direct ethanol fuel cells

A direct ethanol fuel cell (DEFC), which is less prone to ethanol crossover, is reported. The cell consists of PtRu/C catalyst as the anode, Nafion^® 117 membrane, and Ni–Co–Fe (NCF) composite catalyst as the cathode. The NCF catalyst was synthesized by mixing Ni, Co, and Fe complexes into a polymer matrix (melamine-formaldehyde resins), followed by heating the mixture at 800 °C under inert atmosphere. TEM and EDX experiments suggest that the NCF catalyst has alloy structures of Ni, Co and Fe. The catalytic activity of the NCF catalyst for the oxygen reduction reaction (ORR) was compared with that of commercially available Pt/C (CAP) catalyst at different ethanol concentrations. The decrease in open circuit voltage (V_oc) of the DEFC equipped with the NCF catalysts was less than that of CAP catalyst at higher ethanol concentrations. The NCF catalyst was less prone to ethanol oxidation at cathode even when ethanol crossover occurred through the Nafion^®117 film, which prevents voltage drop at the cathode. However, the CAP catalyst did oxidize ethanol at the cathode and caused a decrease in voltage at higher ethanol concentrations.