Demonstration of a tool for automatic learning and re-use of knowledge in the activated sludge process.

Wastewater treatment plant operators encounter complex operational problems related to the activated sludge process and usually respond to these by applying their own intuition and by taking advantage of what they have learnt from past experiences of similar problems. However, previous process experiences are not easy to integrate in numerical control, and new tools must be developed to enable re-use of plant operating experience. The aim of this paper is to investigate the usefulness of a case-based reasoning (CBR) approach to apply learning and re-use of knowledge gained during past incidents to confront actual complex problems through the IWA/COST Benchmark protocol. A case study shows that the proposed CBR system achieves a significant improvement of the benchmark plant performance when facing a high-flow event disturbance.     

Analysis of phosphorus removal and anaerobic selector performance in a full-scale activated sludge process in Singapore.

This paper analyses the performance of the anaerobic selector (A/O process) in a full-scale activated sludge process receiving mostly industrial sewage discharge (> 60%) in Singapore. In addition to the sludge settleability, enhanced biological phosphorus removal (EBPR) was studied. The sludge volume index (SVI) reduced from 200 to 80 ml g(-1) and foaming was suppressed significantly, indicating the effectiveness of the anaerobic selector in improving sludge settleability. The phosphorus removal efficiency was 66%, and 7.5 mg HAc-COD was consumed per mg PO4(3-) -P removed. In the anaerobic compartment, 31% of the SCOD and 73% of the acetic acid in the settled sewage were removed with PO4(3-) -P release of 14.1 mg PO4(3-)-P l(-1). The linear correlation between PO4(3-) -P release in the anaerobic compartment and PO4(3-) -P uptake in the aerobic compartment indicates that there is about 0.8 mg PO4(3-) -P release in the anaerobic compartment per mg PO34(3-) -P uptake in the aerobic compartment. The fates of volatile fatty acids (VFAs) and its short chain acids (SCAs) in the process were studied and discussed.     

Optimizing the tapping regime on a blast furnace operating at variable speed

The main factors that determine the uniformity with which smelting products are tapped from a blast furnace are the rate of accumulation of the products in the hearth and the tapping rate. The first parameter is in turn determined by the stability of the furnace’s operation and can vary significantly even over the course of 24 h. The second parameter is determined mainly by the condition of the iron notch, the maintenance it receives, any changes that occur in the diameter of the channel of the notch, and the quality of the materials used to form the notch. Recommendations are presented to optimize tapping of the smelting products.     

On the problem of hydrogen removal during heat treatment of large forgings

The solutions to a differential equation for the problem of heating of a cylinder in a medium with a fixed temperature are used to obtain equations for estimating the change in the hydrogen concentration in forgings from data on the hydrogen concentration at the cylinder axis or on the average bulk hydrogen concentration. Similar equations are also obtained for forgings having square cross sections. The calculation demonstrates that, for the case of a twofold decrease in the hydrogen concentration in a forging, the calculated times of annealing of a cylindrical forging differ by three times.     

加快能源工业用钢开发支撑国家能源战略实施——武钢发展战略的思考

能源给人类带来光明,能源给社会进步提供了动力,尤其是进入21世纪以来,能源的可持续发展己成为直接影响世界经济社会可持续发展的决定性因素之一。中国政府高瞻远瞩地提出到2020年要实现国民经济翻两番和建设节约型社会的目标,描绘了支撑这一发展目标的十分宏伟的能源发展战略,使人振奋,也对我国钢铁产业的发展提出了更高的要求,作为长期以来与我国     

Volumetric out-of-furnace heat treatment of 3600-M3 decomposers

Specifications require that all the welds in 12-m-diam. decomposers with a capacity of 3600 m³ be subjected to high-temperature tempering before going into service in order to alleviate the stresses from the welding operation. Specialists at the organizations VNIIPTkhimnefteapparatury and VNIImontazhspetsstroi have proposed out-of-furnace volumetric (complete) of the assembled decomposer with the use of special heaters. The use of this heating method has shortened assembly operations while providing the welds with a highquality heat treatment and reducing the stresses overall (including welding stresses, stresses from assembly of the decomposer, etc.) The technology ensures uniform heating of the housing of the decomposer and provides for close control over the process. The experience gained in heat-treating decomposers can also be used in the construction of other containers that come into contact with corrosive media. __________ Translated from Metallurg, No. 3, pp. 61–64, March, 2006.     

Co-digestion of ruminal content and blood from slaughterhouse industries: influence of solid concentration and ammonium generation.

At the present time, organic solid wastes from industries and agricultural activities are considered to be promising substrates for biogas production via anaerobic digestion. Moreover solids stabilisation is required before reutilization or disposal. Slaughterhouses are among the most important industries in Uruguay and produce 150,000 tons of ruminal content (RC) and 30,000 tons of blood per year. In order to determine the influence of the solids and blood contents, the ammonia inhibition and the inoculum adaptation co-digestion batch tests were performed. A set of experiences with TS concentration of 2.5%, 5% and 7.5% and different ratios of RC/blood were carried out using an inoculum from an UASB reactor. In all experiences fast blood hydrolisation was observed. A higher methane production was detected in the experiences with higher TS content. However, the fraction of solids degradation was lower in these experiences. A plateau in the biogas production was found. The free ammonia level, which was above the reported inhibitory levels, could explain this behaviour. After the inhibition period the biogas production restarted probably due to the biomass acclimatisation to the ammonia. In order to determine the inoculum adaptation a new experiment was performed. The inoculum used was the sludge coming from the first set of experiences. Based upon batch tests a 3.5 m3 pilot reactor was designed and started up. Ammonia inhibition was avoided by the start-up strategy and in two weeks the biogas production was 3.5 m3/d. The VS stabilisation with a solid retention time of 20 days was of 43%. The pilot reactor working at steady state had a TS concentration of 3-4% with a ratio of RC/blood of 10:1 at the entrance.     

Catalytic epoxidation of olefins in the presence of a vanadyl porphyrin complex

It was found that vanadyl porphyrin complexes synthesized from petroleum metal porphyrin concentrates stimulated epoxidation during the olefin oxygenation process. The yields of obtained oxiranes turned out to be 38–75%, depending on the olefin structure. An epoxidation mechanism that suggests the formation of a protonated dioxygen adduct as an intermediate during oxygenation of olefins in the presence of vanadyl porphyrin complexes was proposed. An analogy is drawn between the epoxide formation reaction upon the catalytic oxygenation of olefins and the Prilezhaev reaction.     

Vacuum degassing of chromium-nickel-molybdenum steel at the Magnitogorsk Metallurgical Combine

The Magnitogorsk Metallurgical Combine has conducted a study of the effect of technological factors on the hydrogen content of chromium-nickel-molybdenum steel after vacuum degassing. It was established that the most important factor is the hydrogen content of the steel before the degassing operation. The study also determined the effects of the circulation coefficient, the duration of the degassing operation, and the vacuum used in the treatment. __________ Translated from Metallurg, No. 7, pp. 68–69, July, 2006.     

Inhibition of microbial growth in ready‐to‐eat food stored at ambient temperature by modified atmosphere packaging

This study was undertaken to develop a modified atmosphere package to control microbial growth in ready‐to‐eat (RTE) products stored at ambient temperature. Ethanol and/or limonene associated with modified atmosphere (CO₂ : O₂ : N₂ = 30% : 5% : 65%) was used to inhibit the growth of total air‐borne microorganisms and Escherichia coli in RTE products stored at 25°C. The results indicated that 0.05% ethanol vapour in the headspace was effective to inhibit the growth of air‐borne microorganisms and E. coli at 25°C for 72 h in a model study, and the effectiveness was related to ethanol content. Both 73 ppm limonene and 0.05% ethanol vapour enhanced the bacteriostatic effect of modified atmosphere in RTE sushi roll products, and no off‐flavour was detected using this formulated gas; however, no significant inhibitory effect was observed for RTE cold noodle products. This study concludes that combinations of carbon dioxide, ethanol or limonene vapours are effective to inhibit microbial growth in RTE food at ambient temperature, and the outcome may be due to the hurdle effect. Copyright © 2003 John Wiley & Sons, Ltd.