Similarities in normal and binocularly rivalrous viewing

We report here a series of observations-most of which the reader can experience directly-showing that distinct components of patterned visual stimuli (orthogonal lines of a different hue) vary in perception as sets. Although less frequent and often less complete, these perceptual fluctuations in normal viewing are otherwise similar to the binocular rivalry experienced when incompatible scenes are presented dichoptically.     

Novel level-identifying circuit for flash multilevel memories

This paper presents a high-speed, small-area circuit specifically designed to identify the levels in the read out operation of a flash multilevel memory. The circuit is based on the analog computation of the Euclidean distance between the current read out from a memory cell and the reference currents that represent the different logic levels. An experimental version of the circuit has been integrated in a standard double-metal 0.7-μm CMOS process with a die area of only 140×100 μm². Operating under a 5-V power supply, this circuit identifies the read-out current of a memory cell, and associates it with the appropriate logic level in 9 ns     

Voiced speech excitation synthesis using a sinusoidal model

A modification to the `shape-invariant' sinusoidal speech model is proposed, whereby the phases of the component sinewaves used for the excitation are made to add coherently at each glottal closure. Applied to pitch and time-scale modification, higher quality synthetic speech is produced when large changes are required     

Current-mode A/D converter

The authors report the design of a new current-mode A/D converter, based on a modified successive-approximations model, in 1.2 μm CMOS technology. The proposed circuit is characterised by good accuracy and fast dynamic performance, low power consumption and small occupation area. SPICE simulations allow the design approach to be validated and the electrical performance of the ADC to be predicted     

Filter matrix estimation in automated DNA sequencing

In four-color fluorescence-based automated DNA sequencing, a 4×4 filter matrix parameterizes the relationship between the dye-intensity signals of interest and the data collected by an optical imaging system. The filter matrix is important because the estimated DNA sequence is based on the dye intensities that can only be recovered via inversion of the matrix. Here, the authors present a calibration method for the estimation of the columns of this matrix, using data generated through a special experiment in which DNA samples are labeled with only one fluorescent dye at a time. Simulations and applications of the method to real data are provided, with promising results     

合成己二腈反应技术研究——(Ⅴ)己二腈工业反应过程模拟与反应器改造

对己二腈工业反应器提出了两釜串联带回流的模型,通过模拟计算得出模型的级间返混系数 f=6的结论。该模型能较好地预测工业反应器中物料组分浓度变化和气、液两相的流动特性;指出了现工业反应器的鼓泡中和段体积偏小是造成己二酸浓度偏高的关键;提出了可以通过增加串连一个鼓泡预反应段的改造方案,能有效地降低己二酸的浓度,从7%降至4%左右,从而能较好地减缓腐蚀和结焦。     

Drift hole mobility in strained and unstrained doped Si1-xGex alloys

Results of the drift hole mobility in strained and unstrained SiGe alloys are reported for Ge fractions varying from 0 to 30% and doping levels of 10¹⁵-10¹⁹ cm^-3. The mobilities are calculated taking into account acoustic, optical, alloy, and ionized-impurity scattering. The mobilities are then compared with experimental results for a boron doping concentration of 2×10¹⁹ cm^-3. Good agreement between experimental and theoretical values is obtained. The results show an increase in the mobility relative to that of silicon     

Efficient diode-pumped single-frequency erbium:ytterbium fiberlaser

We report a 7.6-mW single-frequency fiber laser operating at 1545 nm, using for the first time an Er³⁺:Yb³⁺ doped fiber and a fiber grating output coupler. The laser did not exhibit self-pulsation, which is a typical problem in short three-level fiber lasers, and had a relative intensity noise (RIN) level below -145.5 dB/Hz at frequencies above 10 MHz. The linewidth of the laser was limited by the relaxation oscillation sidebands in the optical spectrum and was typically less than 1 MHz     

Modeling ion implantation of HgCdTe

Ion implantation of boron is used to create n on p photodiodes in vacancy-doped mercury cadmium telluride (MC.T). The junction is formed by Hg interstitials from the implant damage region diffusing into the MC.T and annihilating Hg vacancies. The resultant doping profile is n⁺/n^-/p, where the n⁺ region is near the surface and roughly coincides with the implant damage, the n^- region is where Hg vacancies have been annihilated revealing a residual grown-in donor, and the p region remains doped by Hg vacancy double acceptors. We have recently developed a new process modeling tool for simulating junction formation in MC.T by ion implantation. The interstitial source in the damage region is represented by stored interstitials whose distribution depends on the implant dose. These interstitials are released into the bulk at a constant, user defined rate. Once released, they diffuse away from the damage region and annihilate any Hg vacancies they encounter. In this paper, we present results of simulations using this tool and show how it can be used to quantitatively analyze the effects of variations in processing conditions, including implant dose, annealing temperature, and doping background.