Monitor-based evaluation of pollutant load from urban stormwater runoff in Beijing.

As a major pollutant source to urban receiving waters, the non-point source pollution from urban runoff needs to be well studied and effectively controlled. Based on monitoring data from urban runoff pollutant sources, this article describes a systematic estimation of total pollutant loads from the urban areas of Beijing. A numerical model was developed to quantify main pollutant loads of urban runoff in Beijing. A sub-procedure is involved in this method, in which the flush process influences both the quantity and quality of stormwater runoff. A statistics-based method was applied in computing the annual pollutant load as an output of the runoff. The proportions of pollutant from point-source and non-point sources were compared. This provides a scientific basis for proper environmental input assessment of urban stormwater pollution to receiving waters, improvement of infrastructure performance, implementation of urban stormwater management, and utilization of stormwater.     

大朝山水电站地下洞室安全监测资料分析

大朝山水电站引水发电系统为地下工程，根据各项安全监测物理量的主要观测成果，对最大观测值分析其对工程的安全影响，为保证其安全运行具有重要意义。为此，分别对大朝山水电站的主要地下建筑物，包括压力引水隧洞、地下厂房、尾水调压室的最大观测值进行了分析研究，并提出了一些建议，有较大的参考价值。     

软β核素内部样品塑料闪烁探测器

本文评价了塑料闪烁片用作软β核素探测器时的计数效率、β谱、本底谱和康普顿电子谱的特征。文中强调:采用胶合光导剂构成的系统是一种新型探测器(软β核素内部样品塑料闪烁探测器)。本文提出内部样品固体探测器、胶合光导剂和胶合闪烁光导剂的新概念。     

Corrosion Inhibition Mechanism with Spilt Cell Technique of Rare Earth Metal on LC4 Al Alloy

A new method of studying the corrosion inhibition mechanism of rare earth metal(REM) on LC4 Al alloy with the spilt cell technique was studied. The principle and experimental method of the spilt cell technique were analyzed. By measuring the change of net-electric current between the two electrodes caused by the change of the amount of oxygen in the solution and the addition of CeCl₃, the influence of corrosive performance of CeCl₃ on LC4 super-power aluminum alloy in the 0.1 mol·L⁻¹ NaCl solution was investigated. Meanwhile, the conditional changes of pH values, CeCl₃ solution, additire and time of performance were also studied. Finally, the features of electrode surface were revealed by using SEM and X-ray energy-dispersive spectrometry (EDS). By combining these with other electric chemical techniques, such as potential-time curve, polarization curve et al.     

甘三酯立体专一分析的研究：（Ⅱ）甘三酯立体专一分析方法初探

在第一部分综合讨论的基础上对甘三酯立体专一分析方法作了初步探讨。以液体油(菜油)及固体脂(猪脂)为基质,系统地研究了这一分析方法,取得了经验并补充了一些具体验证方法。分析液体油的结果与文献数据相一致,分析猪脂的结果欠佳,还存在一些问题需待进一步研究。     

Theoretical analysis of RAIM in the occurrence of simultaneous two-satellite faults

Most algorithms on receiver autonomous integrity monitoring (RAIM) are under the assumption of a single-satellite fault, because there is an extremely small probability that significant simultaneous multiple-satellite faults may occur. However, after the implementation of the Galileo system in a few years, there will be more satellites in view for the user to utilise together with GPS satellites, and a combination of them will bring better performance for RAIM. On the other hand, with the help of wide area augmentation system and the use of dual-frequency operation, pseudo-range errors will be reduced greatly. Thus, tighter alert limits are required for RAIM, and formerly `small' errors should not be neglected. All of those factors make it necessary to consider simultaneous multiple-satellite faults. A detailed theoretical analysis of RAIM under the condition of two-satellite faults for both vertical and horizontal directions is presented. The characteristic/max slopes for every pair of satellites are then deduced in order to calculate the tighter vertical/horizontal protection level for RAIM     

Model Validation for Bridge-Road-Vehicle Dynamic Interaction System

The dynamic response of highway bridges subjected to moving truckloads has been observed to be dependent on (1) dynamic characteristics of the bridge; (2) truck configuration, speed, and lane position on the bridge; and (3) road surface roughness profile of the bridge and its approach. Historically, truckloads were measured to determine the load spectra for girder bridges. However, truckload measurements are either made for a short period of time [for example, weigh-in-motion (WIM) data] or are statistically biased (for example, weigh stations) and cost prohibitive. The objective of this paper is to present results of a 3D computer-based model for the simulation of multiple trucks on girder bridges. The model is based on the grillage approach and is applied to four steel girder bridges tested under normal truck traffic. Actual truckload data collected using a discrete bridge WIM system are used in the model. The data include axle loads, truck gross weight, axle configuration, and statistical data on multiple presence (side by side or following). The results are presented as a function of the static and dynamic stresses in each girder and compared with code provisions for dynamic load factor. The study provides an alternate method for the development of live-load models for bridge design and evaluation.     

Preparation and photochromism of nanocomposite thin film based on polyoxometalate and polyethyleneglycol

A photochromic nanocomposite based on Keggin structure phosphomolybdic acid (PMoA) well dispersed in polyethyleneglycol (PEG) was fabricated. TEM image showed that PMoA nanoparticles with narrow size distribution were finely dispersed in polymer matrix. FT-IR results showed that the Keggin geometry of polyoxometalates was still preserved inside the composites and strong coulombic interaction was built between PMoA and polymer matrix. Under UV irradiation, the film was reduced photochemically to yield a blue species, which was in accordance with a charge-transfer mechanism.     

On structural and high temperature electrochemical properties of ZrO2 thin film coating on Zr metal produced by carbonate melt

Melt of NaCO₃ can favor oxidation of Zr to form ZrO₂ thin film on Zr surface, which is used to make Zr/ZrO₂ oxidation/reduction electrode of pH sensor for testing elevated temperature aqueous solutions. Using SEM, EPMA, XPS, EXAFS and HRTEM, we found that ZrO₂ film is tightness and solid with 20 μm thickness composed by nanometer-sized monoclinic crystals. Zr/ZrO₂ interface is characterized of zoning structure according to topography and chemical composition in five zones: oxygen-rich ZrO₂, ZrO₂, oxygen-rich Zr metal, oxygen-bearing Zr and Zr from outmost to center. Melt oxidation process of Zr involved oxidation time, air and temperature. The air is important effect on structural and electrochemical properties of ZrO₂ thin film for making elevate temperature electrochemical sensor. If oxygen air largely presented in carbonate melting process, ZrO₂ thin film is not tightness and not for oxidation/reduction electrode.