Using decision analysis to determine optimal experimental design for monitoring sewer exfiltration with tracers.

The tracer methods developed to assess exfiltration from sewers in the European project APUSS (assessment of the performance of sewer systems) have a high degree of freedom with regard to the choice of tracer and the dosing strategy. These can lead to very different degrees of uncertainty in the measured exfiltration ratio. In this study, we demonstrate how to select an optimal experimental design using decision analysis, which accounts for this uncertainty and its associated costs. Although the results are site-specific, we can conclude generally that, when NaCl is used as the tracer, the accuracy of the exfiltration estimate is most sensitive to the amount of tracer used and the starting time of the experiment.     

Tracking influent inorganic suspended solids through wastewater treatment plants.

From an experimental and theoretical investigation of the continuity of influent inorganic suspended solids (ISS) along the links connecting the primary settling tank (PST), fully aerobic or N removal activated sludge (AS) and anaerobic and aerobic sludge digestion unit operations, it was found that the influent wastewater (fixed) ISS concentration is conserved through primary sludge anaerobic digestion, activated sludge and aerobic digestion unit operations. However, the measured ISS flux at different stages through a series of wastewater treatment plant (WWTP) unit operations is not equal to the influent ISS flux, because the ordinary heterotrophic organisms (OHO) biomass contributes to the ISS flux by differing amounts depending on the active fraction of the VSS solids at that stage.     

One-dimensional GIS-based model compared with a two-dimensional model in urban floods simulation.

A GIS-based one-dimensional flood simulation model is presented and applied to the centre of the city of N?mes (Gard, France), for mapping flow depths or velocities in the streets network. The geometry of the one-dimensional elements is derived from the Digital Elevation Model (DEM). The flow is routed from one element to the next using the kinematic wave approximation. At the crossroads, the flows in the downstream branches are computed using a conceptual scheme. This scheme was previously designed to fit Y-shaped pipes junctions, and has been modified here to fit X-shaped crossroads. The results were compared with the results of a two-dimensional hydrodynamic model based on the full shallow water equations. The comparison shows that good agreements can be found in the steepest streets of the study zone, but differences may be important in the other streets. Some reasons that can explain the differences between the two models are given and some research possibilities are proposed.     

Strain hardening due to deformation twinning in α-titanium: Mechanisms

Novel experiments were conducted to elucidate the effect of deformation twinning on the mechanical response of high-purity α-titanium deformed at room temperature. Orientation-imaging microscopy (OIM), microhardness, and nanohardness evaluations were employed in conjunction with optical microscopy and quasi-static compression testing to obtain insight into the deformation mechanisms. Hardness measurements revealed that the newly formed deformation twins were harder than the matrix. This observation is perhaps the first experimental evidence for the Basinski mechanism for hardening associated with twinning, arising from the transition of glissile dislocations to a sessile configuration upon the lattice reorientation by twinning shear. This work also provided direct evidence for two competing effects of deformation twinning on the overall stress-strain response: (1) hardening via both a reduction of the effective slip length (Hall-Petch effect) and an increase in the hardness of twinned regions (Basinski mechanism) and (2) softening due to the lattice reorientation of the twinned regions.     

Optimizing the tapping regime on a blast furnace operating at variable speed

The main factors that determine the uniformity with which smelting products are tapped from a blast furnace are the rate of accumulation of the products in the hearth and the tapping rate. The first parameter is in turn determined by the stability of the furnace’s operation and can vary significantly even over the course of 24 h. The second parameter is determined mainly by the condition of the iron notch, the maintenance it receives, any changes that occur in the diameter of the channel of the notch, and the quality of the materials used to form the notch. Recommendations are presented to optimize tapping of the smelting products.     

On the problem of hydrogen removal during heat treatment of large forgings

The solutions to a differential equation for the problem of heating of a cylinder in a medium with a fixed temperature are used to obtain equations for estimating the change in the hydrogen concentration in forgings from data on the hydrogen concentration at the cylinder axis or on the average bulk hydrogen concentration. Similar equations are also obtained for forgings having square cross sections. The calculation demonstrates that, for the case of a twofold decrease in the hydrogen concentration in a forging, the calculated times of annealing of a cylindrical forging differ by three times.     

Prominent consequences of role stress: A meta-analytic review.

Role stress has received a lot of research attention in psychological, sociological, and organizational studies over the last several decades. Based on a literature review of about 300 journal articles, this article examines prominent consequences of role stress. Specific focus is on researching differences in relationships between facets of role stress (i.e., role ambiguity, role conflict, and role overload) and frequently cited consequences using techniques of meta-analysis. Findings indicate that each role stress facet has a different relationship with the eight consequences studied. Role stress research can benefit from looking at each facet individually in addition to role stress generally. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

Word length and lexical activation: Longer is better.

Many models of spoken word recognition posit the existence of lexical and sublexical representations, with excitatory and inhibitory mechanisms used to affect the activation levels of such representations. Bottom-up evidence provides excitatory input, and inhibition from phonetically similar representations leads to lexical competition. In such a system, long words should produce stronger lexical activation than short words, for 2 reasons: Long words provide more bottom-up evidence than short words, and short words are subject to greater inhibition due to the existence of more similar words. Four experiments provide evidence for this view. In addition, reaction-time-based partitioning of the data shows that long words generate greater activation that is available both earlier and for a longer time than is the case for short words. As a result, lexical influences on phoneme identification are extremely robust for long words but are quite fragile and condition-dependent for short words. Models of word recognition must consider words of all lengths to capture the true dynamics of lexical activation. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

On a New Method for H2 -Based Decomposition

This note proposes a simple linear matrix inequality (LMI) system for the design of static precompensators to reduce the interactions of a multivariable system. The approach is based on minimizing the H₂ norm of a modified system and the LMIs are derived from the well known technique of pseudodiagonalisation. The approach is applied to two complex real-life benchmark problems with high levels of interaction. It is shown that its performance is significantly better than previously proposed LMI optimization techniques for designing static precompensators