Synthesis and characterization of biocompatible hydroxyapatite coated ferrite

Ferrite particles coated with biocompatible phases can be used for hyperthermia treatment of cancer. We have synthesized substituted calcium hexaferrite, which is not stable on its own but is stabilized with small substitution of La. Hexaferrite of chemical composition (CaO)_0.75(La₂0₃)_0.20(Fe₂O₃)₆ was prepared using citrate gel method. Hydroxyapatite was prepared by precipitating it from aqueous solution of Ca(NO₃)₂ and (NH₄)₂HPO₄ maintaining pH above 11. Four different methods were used for coating of hydroxyapatite on ferrite particles. SEM with EDX and X-ray diffraction analysis shows clear evidence of coating of hydroxyapatite on ferrite particles. These coated ferrite particles exhibited coercive field up to 2 kOe, which could be made useful for hysteresis heating in hyperthermia. Studies by culturing BHK-21 cells and WBC over the samples show evidence of biocompatibility. SEM micrographs and cell counts give clear indication of cell growth on the surface of the sample. Finally coated ferrite particle was implanted in Kasaulli mouse to test its biocompatibility. The magnetic properties and biocompatibility studies show that these hydroxyapatite coated ferrites could be useful for hyperthermia.     

Electrochemical synthesis and characterization of chloride doped polyaniline

Chloride doped polyaniline conducting polymer films have been prepared in a protic acid medium (HCl) by potentiodynamic method in an electrochemical cell and studied by cyclic voltammetry and FTIR techniques. The FTIR spectra confirmed Cl^- ion doping in the polymers. The polymerization rate was found to increase with increasing concentration of aniline monomer. But the films obtained at high monomer concentration were rough having a nonuniform flaky polyaniline distribution. Results showed that the polymerization rate did not increase beyond a critical HCl concentration. Cyclic voltammetry suggested that, the oxidation-reduction current increased with an increase in scan rate and that the undoped polyaniline films were not hygroscopic whereas chloride doped polyaniline films were found to be highly hygroscopic.     

大位移井钻柱振动规律研究与应用

在大位移井钻井工程中钻柱受着各种振动，当各种振动共振时，钻柱承受着非常大的动载，很容易受损，同时，钻柱的振动影响着井壁的稳定，严重威胁着井下的作业安全。以大位移井近井底的钻柱为研究对象，分析了钻柱振动行为所遵循的规律。采用线性分析法，获得了大位移井钻柱横向振动和扭转振动的频谱方程。同时获得了钻柱各种共振频率的分布。经分析表明：大位移井钻柱的横向振动和扭转振动的共振频率与实际钻井转速非常接近，应合理选择转速以减小钻柱共振的发生。文章的分析研究为大位移井钻柱动态行为的研究提供了理论依据。     

A high-performance multichannel dual-gate poly-Si TFT fabricated by excimer laser irradiation on a floating a-Si thin film

A new excimer laser annealing (ELA) process that uses a floating amorphous-Silicon (a-Si) thin film with a multichannel structure is proposed for high-performance poly-Si thin-film transistors (TFTs). The proposed ELA method produces two-dimensional (2-D) grain growth, which can result in a high-quality grain structure. The dual-gate structure was employed to eliminate the grain boundaries perpendicular to the current flow in the channel. A multichannel structure was adapted in order to arrange the grain boundary to be parallel to the current flow. The proposed poly-Si TFT exhibits high-performance electrical characteristics, which are a high mobility of 504 cm/sup 2//Vsec and a low subthreshold slope of 0.337 V/dec.     

一种基于混沌同步的噪音衰减算法

论文提出了一种混沌通信系统的噪音衰减算法,该算法利用混沌同步现象在接收端获得正确的噪音估计值,从而从接收信号中滤除噪音恢复出正确的信号。通过数值仿真试验表明该方法是可行的。     

基于素性检验思想的不可约多项式判断

论文将Fermat素性检验的思想运用于不可约多项式的判断,给出了一个对于不可约判断问题的Monte Carlo 算法,分析了该算法的计算复杂度问题,并且给出了次数在200以内的检验结果。     

Acquisition and pattern recognition of spectrum information of welding metal transfer

With the creation of a pattern recognition system for metal transfer mode, this article has collected five kinds of spectrum signals in gas metal arc welding (MIG, MAG and CO₂) and take them as training samples. These samples have been pretreated by computer, several key characteristic parameters of the spectrum signal have been creatively extracted, and a corresponding recognition function and a minimum-distance-classifier have been constructed. The results show that the pattern recognition of several kinds of metal transfer modes for the metal gas arc welding can be done successfully, and relative important parameters in welding process, such as the frequency of droplet transfer and the approximate diameter of each droplet, can also be obtained.     

MULTICARRIER DS—CDMA WITH ADAPTIVE MODULATION AND POWER ALLOCATION

Adaptive modulation and power allocation is introduced into the multicarrier DSCDMA system to improve the system performance and bandwidth efficiency.First,the system design appropriate for adaptive modulation and power allocation is given,then the algorithm of adaptive modulation and power allocation is applied.Simulation results demonstrate great performance improvement compared with the fixed modulated one.     

数值试井在白6-2井测试资料分析评价中的应用

数值试井是在近来发展的一项新的试井解释技术，具有处理非均质，复杂边界油气藏问题的优点，弥补了常规解析试井技术的不足。运用数值试井解释技术，结合动、静态资料，通过对白6-1断块白6-2井测试资料的综合分析评价，确定了储层渗流参数，落实了该气藏的边界情况，为该断块下一步开发提供可靠依据。     

Analysis of the mechanism of die soldering in aluminum die casting

A mechanism of soldering of an aluminum alloy die casting to a steel die is proposed. A soldering critical temperature is postulated, at which iron begins to react with aluminum to form an aluminum-rich liquid phase and solid intermetallic compounds. The liquid joins the die with the casting upon solidification. The critical temperature is determined by the elements in both the casting alloy and the die material and is equal to the solidus temperature of the resulting alloy. The critical temperature is used to predict the onset of die soldering, and the local liquid fraction is related to the soldering tendency. Experiments have been carried out to validate the concept and to determine the critical temperature for die soldering in an iron-aluminum system. Thermodynamic calculations are used to determine the critical temperature and soldering tendency for the cases of pure aluminum and a 380 alloy in a steel mold. Factors affecting the soldering tendency are discussed, and methods for reducing die soldering are suggested.