The As-prepared surfaces of C-axis-oriented Nd1Ba2Cu3Oy thin films characterized using scanning probe microscopes

Recently, superconducting Nd₁Ba₂Cu₃O_y (Ndl23) thin films with high superconducting transition temperature (T _c) have been successfully fabricated at our institute employing the standard laser ablation method. In this paper, we report the results of surface characterization of the Nd123 thin films using an ultrahigh vacuum scanning tunneling microscope/spectroscopy (UHV-STM/STS) and an atomic force microscope (AFM) system operated in air. Clear spiral pattern is observed on the surfaces of Nd123 thin films by STM and AFM, suggesting that films are formed by two-dimensional island growth mode. Contour plots of the spirals show that the step heights of the spirals are not always the integer or half-integer number of thec-axis parameter of the structure. This implies that the surface natural termination layer of the films may not be unique. This result is supported byI-V STS measurements. The surface morphology of the Nd123 thin films is compared with that of thec-axis-oriented Y₁Ba₂Cu₃S_y thin films. Surface atomic images of the as-prepared Nd123 thin films are obtained employing both STM and AFM. STS measurements show that most of the surfaces are semiconductive. The results of STS measurements together with the fact that we are able to see the surface atomic images using scanning probe microscopes suggest that exposure to air does not cause serious degradation to the as-prepared surfaces of Nd123 thin films.     

Fast convergent integral equation solution of strip gratings on dielectric substrate

A fast convergent integral equation solution to the scattering problem of a transverse electric/transverse magnetic (TE/TM) plane wave by a one-dimensional periodic array of thin metal strips on a dielectric substrate is described. The formulation of the integral equation is similar to that derived by Montgomery for a two-dimensional periodic array of thin conductors on a dielectric substrate. However, the basis functions which satisfy the appropriate edge conditions are incorporated here for the unknown current expansion on the strips. Following the standard Galerkin's procedure, one may readily determine the induced currents on the strips and thus the reflected and transmitted fields. Sample numerical results are given and good agreement with previously published data is obtained. It is found that the convergence rate of this method is improved by an order of magnitude. Also it is shown that the dielectric substrate has a strong effect on the scattering from the large spacing strip grating.     

灾难备份系统在任丘市央行的应用

灾难备份的概念所谓“灾难备份”,是指利用技术、管理手段以及相关资源,确保已有的关键数据和关键业务在灾难发生后,在确定的时间内可以恢复和继续运营的过程。灾难备份建设是一项复杂的系统工程,涉及到灾难备份中心选点、灾难备份中心建设,机房建设、基础设施建设等,同时还涉及到灾难备份系统建设、专业运营队伍建设、灾难备份中心运营管理体制建设和灾难备份中心运营管理等工作。因此,建立灾难备份不仅需要投入大量人力、物力和财力,还需要考虑灾难备份系统实施所面临的技术难度和经验不足所带来的风险,以及长期运营管理方面的资金投入。…     

An ideal topology type convergent theorem on scale effect algebras

The famous Antosik-Mikusinski convergent theorem on the Abel topological groups has very extensive applications in measure theory, summation theory and other analysis fields. In this paper, we establish the theorem on a class of effect algebras equipped with the ideal topology. This paper shows also that the ideal topology of effect algebras is a useful topology in studying the quantum logic the- ory.     

火焰原子吸收法测定高铋物料中的铅

本文介绍了在以高铋物料为基体 ,5 %的HNO3 介质中 ,波长 2 17nm处进行火焰原子吸收法测定铅的试验 ,采用标准加入法进行回收率的试验 ,回收率大于 98% ,特征浓度为 0 .0 7μg/ml,结果令人满意 ,能满足炉前样分析的要求     

氧化铝厂渣浆泵机械密封的失效形式及改进措施

本文介绍了渣浆泵机械密封的失效形式,并根据长期现场工作经验,分析了机械密封泄漏的主要原因,据此提出了改进措施,通过对动静环密封面倒角,改变密封面尺寸及载荷系数后有效地解决了由于径向跳动过大而引起的密封面刮碰擦裂的失效问题。     

ZJ510L-B汽车用高强度热轧板的试制

珠钢150t电弧炉-LF(VD)-CSP(紧凑式带材生产)流程试生产的5～8mm ZJ510L-B(0．16C--1．22Mn)汽车用高强度热轧板的铁素体晶粒尺寸为6．0～9．2μm，带状组织为1．5～2．5级，强度极限σb562～610MPa，延伸率δ5 32．0％～38．6％。文中还分析和提出了带状组织的形成原因和改进措施。     

对企业账面利润与现金流量关系的认识

本文阐述了企业账面利润与现金流量的关系 ,指出了企业账面利润与现金流量的四个不同点 ,并且提出了一个现代企业应如何在四个方面做好工作 ,正确处理好这两者的关系。     

Rolling and Lifting Probabilities for Sediment Entrainment

This study addresses the rolling and lifting probabilities for sediment entrainment by incorporating the probabilistic features of the turbulent fluctuation and bed grain geometry. The lognormally distributed instantaneous velocity and uniformly distributed initial grain position, along with a relation between lift coefficient and particle Reynolds number, are used to extend the theoretical formulation of the entrainment probabilities in smooth-bed flows. The two threshold conditions identified herein enable us to precisely define the probabilities of entrainment in the rolling and lifting modes. The results obtained in this study coincide well with the published data. The lifting probability increases monotonously with the dimensionless shear stress θ, which is consistent with the earlier results yet displays improved agreement with the experimental data. The maximum value of rolling probability, with a magnitude of 0.25, occurs at θ ≈ 0.15. For θ<0.05 (or θ>0.6), the rolling (or lifting) probability makes up more than 90% of the total entrainment probability and thus can be used as an approximation to the total probability of entrainment. The proposed rolling and lifting probabilities are further linked to the two separate criteria for incipient motion to explore the critical entrainment probabilities. The results reveal that a consistent probability corresponding to the critical state of sediment entrainment cannot be found.     

In situ polymerization and characterization of polyester‐based polyurethane/nano‐silica composites

Polyester‐based polyurethane/nano‐silica composites were obtained via in situ polymerization and investigated by Fourier‐transform infrared spectroscopy (FTIR), or FTIR coupled with attenuated total reflectance (FTIR‐ATR), Transmission electron microscopy (TEM), atomic force microscopy (AFM), an Instron testing machine, dynamic mechanical analysis (DMA) and ultraviolet‐visible spectrophotometry (UV‐vis). FTIR analysis showed that in situ polymerization provoked some chemical reactions between polyester molecules and nano‐silica particles. FTIR‐ATR, TEM and AFM analyses showed that both surface and interface contained nano‐silica particles. Instron testing and DMA data showed that introducing nano‐silica particles into polyurethane enhanced the hardness, glass temperature and adhesion strength of polyurethane to the substrate, but also increased the resin viscosity. UV‐vis spectrophotometry showed that nano‐silica obtained by the fumed method did not shield UV radiation in polyurethane films. Copyright © 2003 Society of Chemical Industry