Magnetic breakdown phenomena in quasi-two dimensional organic conductors

Magneto-oscillation phenomena of the magnetization in low dimensional organic conductors (BEDT-TTF)₂X, are investigated theoretically, focusing on the magnetic breakdown (MB) occured in high fields. Our full quantum mechanical theory reproduces various oscillations, including the interference difference oscillation, which is prohibited in the so-called network model of semi-classical theory, and demonstrates a smooth crossover to the MB orbit oscillation, or MB phenomenon. This is interpreted in terms of the recursive band structures.     

Principle and operation of a new type motor consisting of piezoelectric device and strain wave gearing

The authors have developed a new type of motor consisting of a piezoelectric device and strain wave gearing, and is called a piezoelectric motor. This is a first step in realizing a low-speed, small-size and lightweight motor. The principle of the motor is that the traveling wave is produced by piezoelectric devices and displacement conversion devices without mechanical resonance, and the torque to rotate the motor is generated by a mechanism of strain wave gearing (circular spline and flexspline) without using friction. The motor is operated at variable frequency and its rotational position (angle) is controlled in open-loop because it is basically a synchronous motor. In this paper, the structure and principle of the proposed motor are explained and the driving method and the mechanical characteristics of an experimental motor also are described. The results are as follows:

• 1 The realizability of the proposed piezoelectric motor is verified experimentally. The experimental motor operates at 2920 steps per revolution, and its speed range is 0 to 960 pps [or 0 to 20 (rpms)].
• 2 The torque characteristics are clarified qualitatively.
• 3 The generated torque of the experimental motor is small (less than 0.03 Nm) and therefore the improvement of the torque is an important subject hereafter.
• 4 It is possible to construct the motor with nonmetallic material. This fact is considered to facilitate obtaining a means to lighten the weight of the motor in the future.

     

Application of CO2 laser heating zone drawing and zone annealing to nylon 6 fibers

Nlon 6 fibers were zone drawn and zone annealed by using a continuous wave carbon dioxide laser to develop their mechanical properties. A laser‐heating zone drawing was carried out under a applied tension of 35.4 MPa at a power density of 9.65 W · cm^?2, and then the zone‐drawn fiber was annealed. A laser‐heating zone annealing was carried out in two steps at a power density of 9.65 W · cm^?2; the first step was carried out under 423 MPa and the second under 517 MPa. The treating temperature of the fiber heated by the CO₂ laser was measured by using an infrared thermographic camera equipped with a magnifying lens. The treating temperature at the zone drawing is 138°C, and those at the first and the second zone annealing are 121 and 125°C, respectively. The second laser‐heated zone‐annealed fiber has a birefringence of 65.2 × 10^?3, a degree of crystallinity of 54%, and a storage modulus of 21 GPa at 25°C. Wide‐angle X‐ray diffraction patterns for the laser‐heated zone‐drawn and the zone‐annealed fibers show (200) reflection and (002/202) doublet due to only an α form on the equator. The laser‐heated zone‐drawn fiber has a melting endotherm peaking at 216°C and a trace of shoulder on the higher temperature side of its peak, and the laser‐heated zone‐annealed fibers have a single melting endotherm peaking at 216°C. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 1711–1716, 2002     

Sorption and diffusion of ionic dyes in anionic cellophane membranes

Experimental steady-state permeability studies have been made with non-ionic, anionic and cationic dyes using carboxy cellulose membranes as anionic substrates. The experimental results show that with increasing bulk ionic strength the diffusion velocities of anionic and cationic compounds increase and decrease, respectively. The diffusion behavior of non-ionic compounds is independent of the ionic strength. Empirical relationships have been deduced which fit the permeation data of the anionic compounds. A new concept is introduced which postulates that the diffusion behavior of colons within an anionic membrane is dependent on the basicity of the fixed ionic groups. In substrates with matrix-bound anionic groups of high basicity, such as carboxy cellulose, the permeability behavior is described in terms of a new diffusion mechanism referred to as the “fluctuating” charge mechanism. This concept can provide a semi-quantitative understanding of the different electrostatic obstruction effects which matrix-bound carboxylate and sulfonate groups have on the permeability of colons. The measured permeability of the counter ions is in qualitative agreement with the proposed diffusion model.     

The role of pressure on thin amorphous carbon films deposited using microwave surface wave plasma CVD

We report the effects of gas composition pressure (GCP) on the optical, structural and electrical properties of thin amorphous carbon (a-C) films grown on p-type silicon and quartz substrates by microwave surface wave plasma chemical vapor deposition (MW SWP CVD). The films, deposited at various GCPs ranging from 50 to 110 Pa, were studied by UV/VIS/NIR spectroscopy, atomic force microscopy, Raman spectroscopy, X-ray photoelectron spectroscopy and current–voltage characteristics. The optical band gap of the a-C film was tailored to a relatively high range, 2.3–2.6 eV by manipulating GCPs from 50 to 110 Pa. Also, spin density strongly depended on the band gap of the a-C films. Raman spectra showed qualitative structured changes due to sp³/sp² carbon bonding network. The surfaces of the films are found to be very smooth and uniform (RMS roughness < 0.5 nm). The photovoltaic measurements under light illumination (AM 1.5, 100 mW/cm²) show that short-circuit current density, open-circuit voltage, fill factor and photo-conversion efficiency of the film deposited at 50 Pa were 6.4 μA/cm², 126 mV, 0.164 and 1.4 × 10^− 4% respectively.     

The effects of oxygen diffusion on the surface photooxidation of polystyrene

This paper further illustrates the applicability of multiple internal reflectance infrared spectroscopy to the analysis of near-surface photooxidation. The results are compared with transmission infrared spectra to evaluate compositional gradients resulting from photooxidation and the influence of oxygen diffusion. The sample was a solvent-cast film of atactic, narrow distribution polystyrene, M_w of 100,000, that had been drawn to a ratio of 3.0 at 110°C by solid state coextrusion. Irradiation of these thin films, ～25μm thickness, was performed on exposure to air at 35°C for periods of up to 6 h using a mercury source emitting at 254 nm. On photooxidation, a board peak appears at 3200–3500 cm^?1, attributable to hydroperoxide formation. The most dramatic increase in the infrared spectra is found for a carbonyl band at 1730 cm^?1. It appears to result from an aromatic acid group since it is shifted to 1660 cm^?1 on immersion of the oxidized polystyrene films in aqueous ammonium hydroxide. It is confirmed that the photooxidation of polystyrene occurs preferentially at the surface and that this reaction rate is greatly reduced in the drawn polystyrene film.     

Impregnation of silk sericin into polyester fibers using supercritical carbon dioxide

Silk sericin was impregnated into polyester fabric using supercritical carbon dioxide (SCCO₂) to overcome polyester hydrophobicity. The effects of sericin molecular weight, pH of sericin, solution and cosolvent types on sericin impregnation were investigated. Enzyme‐hydrolyzed, acid‐, based‐hydrolyzed sericin in SCCO₂, and a 30 kDa sericin in SCCO₂ modified with cosolvents such as water, methanol, 1‐propanol, and acetone; and a modifier: sodium hydroxide solution were used in this work. Impregnation of sericin in polyester was indicated by Fourier transform infrared spectrophotometry (FTIR) and dyeing with acid dye. Degradation of polyester fibers during SCCO₂ process was indicated by scanning electron microscopy (SEM). Methylene blue dyeing was used to realize carboxyl group in polyester. The results showed no impregnation of sericin into polyester by using SCCO₂ modified with cosolvents. However, sericin was impregnated into modified surface polyester since hydrophilic groups such as carboxyl and hydroxyl groups were regenerated by alkaline hydrolysis. Samples impregnated with hydrolyzed sericin showed high color strength of Supranolechtbordeaux B acid dye. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007     

Gelation of poly(vinyl alcohol)/phenol/water solutions and gel spinning

The light transmittance of the gels of poly(vinyl alcohol) (PVA)/phenol/water solutions was examined for the entire range of phenol/water content. Excellent transparency was found for the gels with phenol contents of 70–95 vol %. In full consideration of the results for the transparency and melting temperature of the gels and the viscosity and gelation ability of solutions, the PVA solutions of 75 vol % phenol content were selected for the gel spinning. The maximum dynamic moduli of drawn filaments at 25°C (room temperature) were 42 GPa (15x) for atactic PVA and 45 GPa (14x) for syndiotacticity-rich PVA. © 1995 John Wiley & Sons, Inc.     

Formation and Properties of Ln-Si-O-N Glasses (Ln = Lanthanides or Y)

Homogeneous Y-Si-O-N glasses containing 15 or 20 eq% nitrogen (N) were prepared from compositions with Y/Si ratios in the vicinity of that of the lowest eutectic point on the Y₂O₃–SiO₂ phase diagram. The liquidus on the phase diagram shifted toward lower temperatures by incorporation of N. The density, the elastic moduli, and the glass transition temperature of the Y-Si-O-N glasses increased with incorporation of N. This is due to the closer packing of atoms in the glasses by the substitution of N, which is in three-fold coordination with Si, for O which is in two-fold coordination, and the stronger covalent nature of the Si–N bond compared with the Si–O bond. The coefficient of thermal expansion of the Y-Si-O-N glasses increased with increasing Y content, because the discontinuity of the glass network developed with increasing nonbridging anions by the introduction of Y. In contrast, the glass transition temperature and the elastic moduli increased with Y content due to the high coordination of Y for O, and the relatively high cationic field strength of Y. Furthermore, the effect of cationic field strength on properties of Ln-Si-O-N glasses (Ln = lanthanides or Y) is discussed.     

New class of cellulose fiber spun from the novel solution of cellulose by wet spinning method

A novel cellulose solution, prepared by dissolving an alkali-soluble cellulose, which was obtained by the steam explosion treatment on almost pure natural cellulose (soft wood pulp), into the aqueous sodium hydroxide solution with specific concentration (9.1 wt %) was employed for the first time to prepare a new class of multifilament-type cellulose fiber. For this purpose a wet spinning system with acid coagulation bath was applied. The mechanical properties and structural characteristics of the resulting cellulose fibers were compared with those of regenerated cellulose fibers such as viscose rayon and cuprammonium rayon commercially available. X-ray analysis shows that the new cellulose fiber is crystallographically cellulose II, and its crystallinity is higher but its crystalline orientation is slightly lower than those of other commercial regenerated fibers. The degree of breakdown of intramolecular hydrogen bond at C₃[X_am(C₃)] of the cellulose fiber, as determined by solid-state cross-polarization magic-angle sample spinning (CP/MAS) ¹³C NMR, is much lower than other, and the NMR spectra of its dry and wet state were significantly different from each other, indicating that cellulose molecules in the new cellulose fiber are quite mobile when wet. This phenomenon has not been reported for so-called regenerated cellulose fibers.