Applications and Technologies of All-Solid State Blue Laser

1 Introduction Along with the matureness of laser diode (LD) manufacturing technology, the performance of LD has been improved greatly since 1980s, so various kinds of laser devices based on LD have been developed rapidly, especially the all-solid state lasers. After early experiments and researches, the all-solid state lasers have been commercialized successfully.     

Computer-controlled ion-selective electrode switch

The construction of a microcomputer-controlled electrode switch for use in potentiometric determinations is described. This can be coupled to most of the analytical equipment usually found in laboratories, to enable a setting up of automatic systems capable of performing sequential determinations with several ion-selective electrodes. The assessment of its analytical usage and behaviour are discussed.     

美国的灭火与救援机器人研发综述

设想某一个城镇生产木材调色板的流水线车间里 ,由于电器原因引发了一场火灾 ,致使建筑物坍塌。没有人能够确切地说出有多少工人被埋压在里面 ,更糟的是 ,当毗邻墙体坍塌时 ,隔壁的旧轮胎储藏室也被埋压在下面。于是市消防局派遣一批机器人去现场救援。第一个到达的机器人进入现场调查情况 ,该机器人能忍耐80 0℃的高温炙烤 ,身上安装了摄像机 ,可以给 90 m外的控制室发送图片 ,控制室的指挥人员就可以根据图片决定是否派消防队员冒险进入现场。第二个机器人是无人驾驶卡车 ,进入后便从 75 m远的地方以2 6 gal/ s的速度往火场喷水 ,并用它所…     

直流电弧炉长弧泡沫渣技术

本文指出了直流电弧炉采用长弧泡沫渣技术的必要性及该技术的发展现状，总结了炉渣物理性质，化学成分，温度和气源等对炉渣泡沫化的影响，并介绍了电炉泡沫渣的操作工艺及实际应用效果，对宝钢三期１５０ｔＤＣ－ＵＨＰ电弧炉的泡沫渣工艺提出了看法。     

基于动态时间规整的手势加速度信号识别

为了提高基于加速度传感器的动态手势识别算法的性能,本文采用了动态时间规整(DTW)识别算法。通过该算法计算测试模板和参考模板的相似度,从而得出识别结果。为了验证该方法,建立了一套手势加速度无线采集系统,并采集了41个志愿者的手势信息。实验结果表明,该方法手势平均识别率在97%以上。与HMM识别算法相比,DTW识别算法在识别的准确率上比HMM识别算法更具优势。     

TiO2/MOFs的制备及污染物降解现状

TiO2是较为成熟的半导体光催化材料,但因TiO2分散性差、量子利用率低、比表面积小、难回收等问题难以工业化.多孔金属有机框架(MOFs)的引入可增强TiO2/MOFs复合材料的光吸收性能,提高电子-空穴对分离效率和提高回收率.基于TiO2/MOFs制备时前驱体添加顺序不同,综述了TiO2/MOFs的3种制备方法(即Ship-in-a-bottle法、Bottle-around-ship法、One-pot法)及TiO2/MOFs光催化机理与性能影响因素,并探讨不同MOFs与TiO2结合的作用机理.最后,对TiO2/MOFs存在的问题提出建议.     

热压变形对灰口铸铁石墨形态的影响

研究了灰口铸铁(HTl50)在900℃大压下量塑性变形后石墨的分布形态，结果表明：随着压下量的增加，石墨片逐渐趋于平行分布；变形过程中发生了碳的回溶，同时伴随着石墨片的断裂；石墨片体积分数及片间距随压下量的增加而逐渐减少。     

Effect of catalysts in the quality of syngas and by-products obtained by co-gasification of coal and wastes. 1. Tars and nitrogen compounds abatement

The aim of this work is to analyse the possibility of using co-gasification technology to process coal mixed with wastes to take profit of its energy content and at the same time to minimize the environmental impact associated with the use of wastes and to diminish the costs of flue gas treatment. The addition to coal of different types of materials, like: pine based waste, petcoke and polyethylene (PE), was not found to give rise to any operational problems, regarding both the feeding system and gasification process and led to higher energy conversions, however, the gas presented higher tars and hydrocarbons content. Several catalysts were tested, such as, dolomite, olivine, nickel and magnesium oxides, zinc oxides and cobalt and molybdenum oxides. Catalyst action was analysed in tars release and also in ammonia compounds reduction. The presence of catalysts allowed increasing hydrogen release, whilst there was a decrease in hydrocarbons and tars contents. A nickel-magnesium oxide was the catalyst that led to the highest reduction in hydrocarbons and tars. This catalyst also led to the lowest NH₃ content in the fuel gas produced, due to the catalyst efficiency in NH₃ destruction.     

甲苯三氧化硫磺化反应抑制副产物二甲苯砜的研究

对SO3磺化甲苯反应的副产物二甲苯砜成因及反应历程进行了分析,通过实验比较了醋酸与二甲苯砜的抑制效果,提出用磺化副产物二甲苯砜自身抑制的新方法.考察了二甲苯砜力入量和甲苯转化率对抑制副反应的影响.反应温度:10℃,三氧化硫:6%,甲苯转化率为35%时,外加甲苯质量3.3%的二甲苯砜就能控制二甲苯砜含量不增加,且甲苯磺酸异构体的对位含量由84%上升到89%,间位含量由2.5%下降到1%.