多媒体网络技术环境下大学英语教学模式的思考

随着多媒体网络技术引入大学英语教学 ,传统的教学模式面临极大的冲击。本文在学生中心论和建构主义学习理论的基础上 ,总结了基于多媒体网络的人机结合的教学模式。通过对比分析传统教学与多媒体网络教学班级学生的学期能力综合测试成绩 ,阐述了实施这种教学模式的制约因素和对策     

Electroless deposition of Ni on template of halloysite and its magnetic property

Halloysite template, a ceramic substrate, is of a hollow cylindric structure, on which the fine Pd nanoparticles are uniformly formed by the reduction of palldate chloride to initiate electroless deposition. The electroless deposition of Ni is catalyzed by the Pd particles, which results in a uniform layer of Ni-P alloy on halloysite. The alloy is of a nanocrystalline structure, of which the average diameter is about 6 nm. After being heat-treated at 400 ℃, it contains both Ni and Ni12P5 crystal, meanwhile, the Ni crystal gets larger with an average size of 51.9 nm.The content of phosphorous in the Ni layer has a great influence on crystal structure. The metallized halloysite has a higher inherent coercive force, and a much lower saturation magnetization in its as-plated state, while after heattreatment, the inherent coercive force decreases drastically. These magnetic properties have great relationship with the superparamagnetism of Ni nanocrystalline and the stress anisotropy in Ni layer.     

基于I2C总线技术的等离子喷焊系统的研究

阐述了基于I^2C总线技术的等离子喷焊过程控制系统的设计原理，介绍了软硬件及接口设计技术。实践表明，采用I^2C总线技术，不仅使系统的芯片大大减少，系统的灵活性增强，而且提高了系统的抗干扰能力。     

Abnormal Austenite-Ferrite Transformation Behaviors of Fe-ISi: Dilatometric Measurements

WITH THE APPEASING of competition of the totaloutput of iron and steels, the new generation of ultrahigh strength steel, based on the lessen the burden ofenvironment, double improvement of mechanicalproperties and elongation of the serving life, has beenfully outspreaded in the world. More and more researchwork shows that the solid-state microstructureevolution becomes the most effective route in thedevelopment of ultra-high strength steels. A process ofgreat interest in the steel produc…     

堆焊用药芯焊丝生产过程中的质量控制

针对堆焊用药芯焊丝生产过程中的质量控制问题，从设备状态、合金粉末、包粉量、焊丝刚度、减径量、拔丝粉、拉拔力和拉拔速度等方面提出了相应的措施，以保证和提高药芯焊丝质量的稳定性。     

ZTC4筒形件温成形扩口数值模拟

对铸造Ti-6Al-4V筒形件温成形扩口成形工艺进行了数值模拟分析,得出了优化的工艺参数,并对凸模锥角进行了优化模拟,得出了合适的锥角。     

液态铝合金表面张力快速检测新方法与装置

表面张力是液态合金的重要物性参数之一,铝合金表面张力与其变质处理效果及充型能力等质量参数密切相关,研究铸造铝合金表面张力快速检测方法及装置,对于开发铝合金熔炼质量炉前实时评价系统具有非常重要的实际意义.介绍了一种液态铝合金表面张力快速测试的新方法和新装置,新方法以固定时间内吹入被测液体的气泡个数以及气泡在生长过程中内部压差变化为信息参数,通过回归公式求解表面张力.基于该方法研制的表面张力新型测试装置由单片机测控单元、探头及其锁紧和升降机构、供气单元等部分构成.采用新装置可在5 s内测得铝合金表面张力,且具有较高的测试精度.     

高钒高速钢碳化钒形态的数值化分析

针对碳化钒的不同形态,设计出定量分析软件,并利用形状因子K,实现了高钒高速钢不同碳化物形态数值化处理,当K介于0.785～1.000之间碳化钒形态为团球状;K≤0.223,碳化钒呈开花状.高钒高速钢当碳含量达到4.2%时,K为0.86和当量直径D为0.78μm,碳化物呈团球状均匀分布.     

初探混联法生产氧化铝的工艺优化

在目前的生产条件下。通过大量的混联法物料衡算，定量地研究了供矿铝硅比、熟料铝硅比和拜年法赤泥铝硅比对混联法的制造成本、能耗和拜年法与烧结法的生产比例的影响规律，提出我国混联法生产进一步优化的方向和途径。并开发了研究和评价的计算软件。为混联法的生产和设计的进一步优化奠定基础。     

Effect of surface modification of metal hydride electrode on performance of MH/Ni batteries

A novel method was applied to the surface modification of the metal hydride(MH)electrode of MH/Ni batteries.Both sides of the electrode were plated with a thin silver film about 0.1μm thick using vacuum evaporation plating technology,and the effect of the electrode on the performance of MH/Ni batteries was examined.It is found that the surface modification can enhance the electrode conductivity and decrease the battery ohimic resistance.After surface modification,the discharge capacity at 5C(7.5A)is increased by 212 mA.h and the discharge voltage is increased by 0.11 V,the resistance of the batteries is also decreased by 32%.The batteries with modified electrode exhibit satisfactory durability.The remaining capacity of the modified batteries is 89%of the initial capacity even after 500 cycles.The inner pressure of the batteries during overcharging is lowered and the charging efficiency of the batteries is improved.