一种使用多跳事实的端到端知识库实体描述生成方法

自动化实体描述生成有助于进一步提升知识图谱的应用价值,而流畅度高是实体描述文本的重要质量指标之一。该文提出使用知识库上多跳的事实来进行实体描述生成,从而贴近人工编撰的实体描述的行文风格,提升实体描述的流畅度。该文使用编码器—解码器框架,提出了一个端到端的神经网络模型,可以编码多跳的事实,并在解码器中使用关注机制对多跳事实进行表示。该文的实验结果表明,与基线模型相比,引入多跳事实后模型的BLEU-2和ROUGE-L等自动化指标分别提升约8.9个百分点和7.3个百分点。     

某矿快速掘进最优炮孔间距的选择

山西某矿5308底抽巷在掘进过程中速度慢、效率低，直接影响工作面的瓦斯抽采，为了改善上述情形，对炮孔间距进行研究。通过使用ANSYS软件对不同炮孔间距下快速掘进效果的模拟分析，并经现场验证，得出了适应该矿的最佳炮孔间距。结果表明：炮孔间距为500 mm时，爆破产生裂隙发育范围和岩石损伤区域都最大，快速掘进的效果最好。     

灰库设计的细节探讨

根据以往的工程设计经验,从实用的角度出发,针对灰库设计中在工艺布置、设备选型及楼面标高的确定、设备及仪表检修等需要考虑的几个细节问题上,进行了总结整理以共同探讨。     

交联聚乙烯电缆绝缘老化超低频介损试验及评价规程研究

本文基于通过检测电缆超低频介损值确定电缆老化程度的基本原理,结合某地实测得到的多组数据,通过国际规程IEEE 400.2—2013进行初步判断,分析处于不同状态下的电缆介损值的变化规律及其原因,并得出该规程仅适用于没有局部劣化的电缆.此外,由于我国电缆制造材料、结构和生产工艺与国外产品存在差异,采用国际规程判断电缆老化程度有时会变得不准确.为解决此类问题,本文建立更加全面的判据体系,给出最优判断阈值的确定方法,并对该地区实测得到的数据进行拟合,得到更加准确的分级判断阈值.此方法可为建立符合我国电缆实际情况的评价规程提供参考.     

Three‐dimensional color prediction modeling of single‐ and double‐layered woven fabrics

In this research, the three‐dimensional structural and colorimetric modeling of three‐dimensional woven fabrics was conducted for accurate color predictions. One‐hundred forty single‐ and double‐layered woven samples in a wide range of colors were produced. With the consideration of their three‐dimensional structural parameters, three‐dimensional color prediction models, K/S‐, R‐, and L*a*b*‐based models, were developed through the optimization of previous two‐dimensional models which have been reported to be the three most accurate models for single‐layered woven structures. The accuracy of the new three‐dimensional models was evaluated by calculating the color differences ΔL*, ΔC*, Δh°, and ΔE_CMC(2:1) between the measured and the predicted colors of the samples, and then the error values were compared to those of the two‐dimensional models. As a result, there has been an overall improvement in color predictions of all models with a decrease in ΔE_CMC(2:1) from 10.30 to 5.25 units on average after the three‐dimensional modeling.     

Preparation and Properties of a New Mediumdensity and High-strength Ceramic Proppant

Based on the needs of the market,a new 52 MPa medium-density and high-strength ceramic proppant was prepared by adopting third grade bauxite and clay as raw materials and using the solid phase sintering method,and the effect of the firing temperature on the microstructure,phase composition and mechanical properties of the ceramic proppant was studied. The broken resistance mechanism of this ceramic proppant was also discussed. The results show that the main phases of the prepared ceramic proppant are mullite and corundum; the broken rates are 3. 92% and 7. 21% under 52 MPa and69 MPa,respectively.     

Hazelett生产线熔炼工艺探讨

探讨了采用Hazelett生产线,从原料到合格铝液各道工序的操作要求;特别是采用电解铝液,对每道工序操作时间和铝液质量控制提出严格要求。通过实际生产,对现有熔炼炉配置、设备台数、精炼设备配置作了详细阐述,对每道工序要达到的铝液净化参数提出严格要求,经过6次净化提纯,基本满足Hazelett铸机要求,并对熔炼设备配置的不足提出合理化建议。