Sampling for representative micropollutant loads in sewer systems.

Most commercially available auto-sampling devices do not support a continuous flow-proportional sampling mode, which would conceptually be the best for collecting representative composite samples. Instead different discrete sampling modes are available. Household chemicals can show considerable random short-term variations. With the anticorrosive benzotriazole, relating to a middle-frequent household activity, we show that, besides an accurate flow meter, mainly three factors are decisive for the representativeness of a substance's average load: the substance's load pattern, the sampling frequency and the length of the composite sample. When the sampling intervals are 10 minutes or longer, errors in the order of +/-40% (standard deviation) or more have to be accepted, if the substance of interest is contained in a low number of wastewater pulses (i.e., the level of household activity). This particularly holds true for specific pharmaceuticals e.g. carbamazepine. Ammonium would be less critical, because it relates to a larger number of sources in the same catchment.     

One-dimensional GIS-based model compared with a two-dimensional model in urban floods simulation.

A GIS-based one-dimensional flood simulation model is presented and applied to the centre of the city of N?mes (Gard, France), for mapping flow depths or velocities in the streets network. The geometry of the one-dimensional elements is derived from the Digital Elevation Model (DEM). The flow is routed from one element to the next using the kinematic wave approximation. At the crossroads, the flows in the downstream branches are computed using a conceptual scheme. This scheme was previously designed to fit Y-shaped pipes junctions, and has been modified here to fit X-shaped crossroads. The results were compared with the results of a two-dimensional hydrodynamic model based on the full shallow water equations. The comparison shows that good agreements can be found in the steepest streets of the study zone, but differences may be important in the other streets. Some reasons that can explain the differences between the two models are given and some research possibilities are proposed.     

Control of reactive distillation production of high-purity isopropanol

The process characteristics and control strategy of a high-purity IPA reactive distillation column were investigated. A robust nominal operation was found by maintaining an excess of propylene feed to the column and recycling the unreacted propylene to the feed instead of the top stage. Stage temperature and propylene composition with one-to-one relationship with reboiler duty and propylene feed are selected as controlled variables for maintaining bottom purity and feed ratio in the presence of possible measurement bias respectively. High nonlinearity between selected input–output pair was reduced by using variable transformation. Dynamic simulations demonstrated that such a control scheme with nonlinear transformed variable was capable of providing much superior control performance than the one using natural variable.     

Sol-Gel Preparation and Luminescence Properties of BaMgAl10O17∶Eu2+ Phosphors

The synthesis of BaMgAl10O17∶ Eu2 (BAM) phosphors using the sol-gel method and their luminescence properties were reported. The blue-light emitting BAM was synthesized using citric acid and ethylene glycol as chelating materials. Emission of blue-light was obtained from these phosphors. The luminescent intensity increases as the temperature of heat treatment is increased. This study investigated the effects of the molar ratio of ethylene glycol to citric acid (Φ value), with respect to the phase formation and luminescence properties of BAM. The variation of the Φ value resulted in the change of the sol-gel reaction mechanism and the microstructures of the resultant powders. An increase in Φ value leads to an increase in the rate of BAM phase formation. The photoluminescent intensity of the prepared phosphors increases with heating temperatures because of enhanced crystallization.     

垦71井区三维VSP资料波场分离方法应用研究

三维VSP资料是多偏移距VSP资料，资料中多种类型的波叠合在一起形成复杂波场。从复杂波场中分离出单一的保幅反射波波场是三维VSP波场分离的重要工作。常规二维VSP波场处理方法单一，难以适用于复杂的三维波场处理。针对三维VSP资料的波场特点，以分离上行反射P波为例，将单一波场分离方法加以适当组合，对垦71井区三维VSP实际资料进行了应用研究。结果表明，波场分离处理中叠加消去法和中值滤波相结合以及F—K滤波和中值滤波相结合的方法克服了单一方法的缺陷，波场处理后获得了波组特征明显、波场清晰单一的上行反射P波保幅波场，取得了较好的波场分离效果。     

Theoretical and practical implications of creep curve shape analyses for 7010 and 7075

Over tensile stress ranges giving creep lives up to 2000 hours at 373 to 463 K, the creep and creep fracture properties of 7010 are compared with results recorded for 7075 and other precipitation-hardened aluminum alloys. Using the ϕ methodology to quantify the systematic variations in creep curve shape with changing test conditions, the behavior patterns displayed by the different alloys are shown to depend on the extent to which precipitate coarsening causes a progressive loss of creep strength with increasing test duration and temperature. The ϕ relationships also introduce new approaches for rationalization and interpretation of creep data sets, based on the activation energy for lattice diffusion in the alloy matrices and the yield stress or UTS at the creep temperatures.     

On a New Method for H2 -Based Decomposition

This note proposes a simple linear matrix inequality (LMI) system for the design of static precompensators to reduce the interactions of a multivariable system. The approach is based on minimizing the H₂ norm of a modified system and the LMIs are derived from the well known technique of pseudodiagonalisation. The approach is applied to two complex real-life benchmark problems with high levels of interaction. It is shown that its performance is significantly better than previously proposed LMI optimization techniques for designing static precompensators     

An element-based displacement preconditioner for linear elasticity problems

Finite element analysis of problems in structural and geotechnical engineering results in linear systems where the unknowns are displacements and rotations at nodes. Although the solution of these systems can be carried out using either direct or iterative methods, in practice the matrices involved are usually very large and sparse (particularly for 3D problems) so an iterative approach is often advantageous in terms of both computational time and memory requirements. This memory saving can be further enhanced if the method used does not require assembly of the full coefficient matrix during the solution procedure. One disadvantage of iterative methods is the need to apply preconditioning to improve convergence. In this paper, we review a range of established element-based preconditioning methods for linear elastic problems and compare their performance with a new method based on preconditioning with element displacement components. This new method appears to offer a significant improvement in performance.     

PowerNap: an efficient power management scheme for mobile devices

We present PowerNap, an OS power management scheme, which can significantly improve the battery life of mobile devices. The key feature of PowerNap is the skipping of the periodic system timer ticks associated with the operating system. On an idle device, this modification increases the time between successive timer interrupts and enables us to put the processor/system into a more efficient low power state. This saves the energy consumed by workless timer interrupts and the excess energy consumed by the processor in less efficient low power states. PowerNap is tightly integrated with the kernel and is designed for optimal control of the latency and energy associated with transitioning in and out of the low power states. We describe an implementation of PowerNap and its impact on system software. Experiments with IBM's WatchPad verify the ability of PowerNap to extend battery life. An analytical model that quantifies the ability of the scheme to reduce power is also presented. The model is in good agreement with experimental results. We apply the model to small form-factor devices which use processors that have a PowerDown state. In such devices, PowerNap may extend battery life by more than 42 percent for small processor workloads and for background power levels below 10 mW.     

Beneficial effects of wettability altering surfactants in oil-wet fractured reservoirs

In fractured reservoirs, an effective matrix-fracture mass transfer is required for oil recovery. Surfactants have long been considered for oil recovery enhancement, mainly in terms of their ability to reduce oil–water interfacial tension. These surfactants are effective when the fractured formations are water-wet, where capillary imbibition of surfactants from the fracture into the matrix contributes to oil recovery. However, another beneficial aspect of surfactants, namely their ability to alter wettability, remains to be explored and exploited. Surfactants capable of altering wettability can be especially beneficial in oil-wet fractured formations, where the surfactant in the fracture diffuses into the matrix and alters the wettability, enabling imbibition of even more surfactant into the matrix. This sequential process of initial diffusion followed by imbibition continues well into the matrix yielding significant enhancements in oil recovery.In order to test this hypothesis of sequential diffusion–imbibition phenomenon, Dual-Drop Dual-Crystal (DDDC) contact angle experiments have been conducted using fractured Yates dolomite reservoir fluids, two types of surfactants (nonionic and anionic) and dolomite rock substrates. A new experimental procedure was developed in which crude oil equilibrated with reservoir brine has been exposed to surfactant to simulate the matrix-fracture interactions in fractured reservoirs. This procedure enables the measurements of dynamic contact angles and oil–water interfacial tensions, in addition to providing the visual observations of the dynamic behavior of crude oil trapped in the rock matrix as it encounters the diffusing surfactant from the fractures. Both the measurements and visual observations indicate wettability alterations of the matrix surface from oil-wet to less oil-wet or intermediate wet by the surfactants. Thus this study is of practical importance to oil-wet fractured formations where surfactant-induced wettability alterations can result in significant oil recovery enhancements. In addition, this study has also identified the need to include contact angle term in the dimensionless Bond number formulations for better quantitative interpretation of rock–fluids interactions.