石油沥青60℃动力粘度测定影响因素的探讨

粘度是表征沥青稠度的一个重要指标。通过论述石油沥青粘度测定法(真空毛细管法)中毛细管的选择、温度、真空度、取样量等对试验结果的影响及试验过程中的其它注意事项,表明了在测定石油沥青的60℃动力粘度时,必须严格按照试验方法的要求进行测定,以保证试验结果的准确性。     

有线网络行业垄断性的改变及竞争形势分析

有线网络行业既具有自然垄断性,又具有行政垄断性.但随技术进步和国家政策的调整,其自然垄断性被削弱,行政垄断也被打破.在位的有线网络企业面临着两个层面的竞争：一是基于不同视频传输方式的竞争,二是同为有线网络传输方式的竞争,而后者是直接的竞争.对有线网络行业的竞争进行了SWOT分析.最后讨论了竞争形势下在位的有线网络运营商的应对思路.     

合成己二腈反应技术研究——(Ⅴ)己二腈工业反应过程模拟与反应器改造

对己二腈工业反应器提出了两釜串联带回流的模型,通过模拟计算得出模型的级间返混系数 f=6的结论。该模型能较好地预测工业反应器中物料组分浓度变化和气、液两相的流动特性;指出了现工业反应器的鼓泡中和段体积偏小是造成己二酸浓度偏高的关键;提出了可以通过增加串连一个鼓泡预反应段的改造方案,能有效地降低己二酸的浓度,从7%降至4%左右,从而能较好地减缓腐蚀和结焦。     

烧结工艺对液相合成（SrPb）TiO3基陶瓷热敏特性影响的研究

本文在液相合成（ＳｒＰｂ）ＴｉＯ３粉的基础上，研究了升温速率、保温时间、烧结温度及降温方式对（ＳｒＰｂ）ＴｉＯ３基陶瓷的Ｖ型ＰＴＣ热敏特性的影响。实验表明：升温速率对其热敏特性影响不大，保温时间和烧结温度的作用是一致的，具有一最佳范围。而降浊方式对材料的热敏特性影响较大。综合各因素的影响，本配方中，样品的烧结制度定为：以２００℃／ｈ的速率升温，在１２５０℃保温１ｈ，炉冷至９５０℃，保温０．５ｈ，再     

实体造型中的几何约束

实体造型是一个基于约束的过程，完成从功能约束到几何约束、再到代数约束的转化而得到实体模型。本文讨论了几何约束的层次性及其表示，并且对几何约束同设计意图的关系进行了研究，提出了基于ＣＳＧ／ＧＣＧ／Ｂ－ｒｅｐ的模型表示。     

大系统分散鲁棒容错控制的进展及主要成果

综述了近２０年来关联大系统分散鲁棒容错控制的研究动态及取得的主要成果。说明了统一地研究分散鲁棒容错控制的必要性。在分散控制、鲁棒控制和容错控制研究领域内，分析了各种设计方法的主导思想及实质；指出了这些研究成果的意义与存在的问题。文中着重论述了分散、鲁棒、容错控制研究方法的发展途径。     

Modeling and CW operation of a quasi-three-level 946 nm Nd: YAG laser

A model is developed for an end-pumped quasi-three-level laser with population in the lower laser level at equilibrium such as for transitions to the manifolds⁴I9/2in Nd³⁺,⁴I15/2in Er³⁺,⁵I8in Ho³⁺and³H6in Tm³⁺. It is shown that the effect of residual lower laser level population on laser operation can be treated as a saturable loss. Room temperature operation on the⁴F3/2-⁴I9/2transition in Nd:YAG under CW dye laser pumping has been demonstrated with a threshold as low as 11.5 mW incident power and a slope efficiency of 7 percent with 0.3 percent output coupling. Performance is limited by the low output coupling and diffraction loss.     

Skeletal Isomerization and Inter—molecular Hydrogen Transfer Reactions in Catalytic Cracking

Bimolecular hydrogen transfer and skeletal isomerization the important secondary reac-tions among catalytic cracking reactions,which affect product yield distribution and product quality,Catalyst properties and operating parameters have great impact on bimolecular hydrogen transfer and skeletal isomerization reactions .Bimolecular hydrogen transfer activity and skeletal isomrization activity of USY-containing catalysts are higher thn that of ZSM-5-containing catalyst.Coke deposition on the active sites of catalyst may suppress bimolecular hydrogen transfer activity and skeletal isomer-ization activity of catlys in different degrees.Short raction time causes a decrease of hydrogen trans-fer reaction,but and increase of skeletal isomerization reaction compared to cracking reaction in catalytic cracking process.     

Sustainable Development and Management of Water Resources in the Hei River Basin of North-west China

The quantitative and qualitative evaluation of water, land and biotic resources in the inland river basins is important in the arid zone. Analysis of the exploitation potential of water resources and the environmental changes through water development can help people in the sustainable development and management of water resources within the basin. Water resources development has affected the scale of oasis establishment in the middle reaches and the existence of lower-reach oases in the Hei River basin. Exploitation and utilization of water resources at the present stage should bring about a harmonic relation between economic development and the ecological environment in the whole basin. The whole area should be considered as an entirety to adopt feasible engineering and administrative measures such as strengthening the protection of water resources in upper streams, macro-control of water consumption and implementing water-saving measures in middle and lower reaches, quantitatively managing and allotting water resources in accordance with regional conditions and adherence to comprehensive rehabilitation. Thus, economic, environmental and social benefits of water resources can be enhanced.     

A concise process technology for 3-D suspended radio frequency micro-inductors on silicon substrate

In this letter, a concise process technology is proposed for the first time to enable the fabrication of good quality three-dimensional (3-D) suspended radio frequency (RF) micro-inductors on bulk silicon, without utilizing the lithography process on sidewall and trench-bottom patterning. Samples were fabricated to demonstrate the applicability of the proposed process technology.