Theoretical and Experimental Study of Water Transport in a Hollow Cylinder Applied to the Drying of Round Squid Mantle

Until now, attention has been focused solely in the drying of squid mantle from an experimental point of view, neglecting the transport phenomenon studies of water in squid muscle. This work studies the drying of squid mantle (Loligo brasiliensis), previously salted and smoked by liquid smoking (hickory extract), using a tubular dryer in closed cycle with a silicagel fixed bed in series. The mass transfer phenomenon during drying was studied, based on the Fick's second law, with the effective diffusivity supposed constant, which enabled an analytical solution to the problem. The drying curve calculated with the resulting equation was compared with experimental data. The model was applied to a hollow cylinder geometry (round squid mantle), with its internal surface isolated from the drying environment by a plastic film. The latter was given a tubular form and introduced inside the mantle cavity (impervious wall boundary condition).     

Attenuation of anticonvulsant effects of diazepam after chronic treatment with bicuculline

Changes in the GABAergic system after chronic treatment with bicuculline were examined in two strains of inbred rats, Fischer 344 (F344) and Lewis (LEW). Rats received an IP injection of either bicuculline (2 mg/kg) or vehicle once a day for 12 days. After this chronic treatment, the effects of diazepam (1 mg/kg, IP) and pentobarbital (20 mg/kg, IP) on bicuculline-induced convulsions were measured. Bicuculline was acutely infused into a tail vein at 0.0415 mg/min, and the infusion was terminated when rats showed seizure. Following the chronic bicuculline treatment, the anticonvulsant effect of diazepam, but not of pentobarbital, was significantly reduced as compared to its effect following chronic vehicle treatment in both strains. Both diazepam and pentobarbital showed a significant difference in anticonvulsant effects between strains (F344 > LEW). The hypnotic effects of muscimol, barbital, pentobarbital, and ethanol following chronic bicuculline treatment were examined. There was no significant difference in sleep time induced by these drugs between bicuculline- and vehicle-treated rats. These results suggest that the attenuation of diazepam's anticonvulsant effect after chronic bicuculline treatment may result from functional changes in benzodiazepine receptors and that the anticonvulsant effects of diazepam and pentobarbital may be influenced by genetic factors. Moreover, the hypnotic effects of several drugs tested are apparently not affected by chronic bicuculline treatment.     

A sensorless brushless dc motor system

This paper describes a brushless dc motor system without position or speed sensor. The brushless motor consists of a permanent magnet synchronous motor and a voltage-source inverter capable of controlling the amplitude and frequency of voltage. The rectangular-shaped stator current with a conducting interval of 120° (electrical) is controlled to be in phase with the trapezoidal back electromotive force. This results in producing maximum torque. Variable speed is achieved by adjusting the average motor voltage similarly to chopper control of dc motors. In this paper, two sensorless position detecting methods, i.e., an “indirect method” suited for the lower-speed range and a “direct method” suited for the higher-speed range are proposed. The combination of the two makes it possible to detect the rotor position over a wide-speed range. Furthermore, a speed-sen-sorless PLL control is proposed in applying the principle of the direct method. Experimental results obtained from a prototype brushless dc motor are shown to confirm the validity of the sensorless drive. The starting procedure of the motor also is discussed because it is impossible to detect the rotor position at a standstill.     

Multiple quasi-phase-matched device using continuous phase modulation of /spl chi//sup (2)/ grating and its application to variable wavelength conversion

We propose a new multiple quasi-phase-matched wavelength converter based on the continuous phase modulation of a /spl chi//sup (2)/ grating for use in variable wavelength conversion. A numerical study shows that the proposed device exhibits a high conversion efficiency, flexible design, and robust fabrication tolerance. A waveguide device fabricated by annealed proton exchange agrees well with the numerical design. Fine-tuning the device enabled us to demonstrate variable wavelength conversion between signals on the standard optical frequency grid. Using the device, we also demonstrated fast (<100 ps) wavelength switching of 4-channel 40-Gb/s signals. The obtained results clearly show that the proposed multiple quasi-phase-matched devices will be useful when constructing future flexible photonic networks.     

Monolithic 2.1 Gbit/s decision circuit with a decision threshold ambiguity width of less than 10 mV

An Si bipolar monolithic decision circuit for practical use is developed using an improved circuit technique and super self-aligned process technology with the reliable 1.25 ?m rule. The circuit consists of a slice amplifier, a master-slave D flip-flop and an output buffer. This circuit is capable of operating up to 2.1 Gbit/s with a decision threshold ambiguity width of less than 10 mV. In addition, a clock phase margin of 250 degrees and power dissipation of 640 mW at VEE=?6 V can be achieved.     

Calciothermic reduction of titanium oxide in molten CaCl<Subscript>2</Subscript>

Titanium oxides were reduced to metallic titanium using the liquid calcium floating on the molten CaCl₂. A part of Ca dissolved into CaCl₂ and reacted with TiO₂ settled below CaCl₂. The by-product CaO also dissolved by about 20 mol pct into CaCl₂, which was effective in reducing the oxygen concentration in the obtained Ti particles. The compositional region in the Ca-CaCl₂-CaO system was examined for the less oxygen contamination in Ti and the better handling in leaching. A large amount of the residual calcium oxidized the titanium powder in leaching. The metallic Ti powder less than 1000 mass ppm oxygen could be obtained only for 3.6 ks using 5 to 7 mol pct Ca-CaCl₂ at 1173 K. The powder was slightly sintered like sponge, and contained approximately 1500 ppm Ca. The anatase phae, the intermediate product in the refining process of TiO₂, could be also supplied as raw material as well as rutile.     

Monte Carlo simulation of hydrogen absorption in palladium and palladium–silver alloys

A modified Monte Carlo (MC) simulation was performed to investigate the hydrogen absorption behavior in Pd and Pd–Ag alloys of the composition Pd_xAg_1−x (x=0.7–0.8) under H₂ pressure (0.1 MPa) at different temperatures. The present method employed can consider the dissociative adsorption of hydrogen molecule and the subsequent absorption of hydrogen atom by formalizing the relationship between the pressure of hydrogen molecule and hydrogen atom. The potential parameters were determined to reproduce the solution enthalpy of hydrogen in pure metals. The results are in good agreement with experimental findings as well as previous theoretical studies. We confirmed that our method is useful to simulate the absorption of hydrogen in metals and alloys.     

Polarity control of GaN epilayers grown on ZnO templates

We report the successful growth of Ga-polar GaN epilayers on O-polar ZnO templates pre-deposited on c-sapphire. Prior to GaN growth, NH₃ is exposed onto the ZnO template. The polarity of the GaN layers is confirmed by etching of the surface and by conversion beam electron diffraction (CBED), while the O-polar ZnO is confirmed by CBED. It is suggested that the NH₃ pre-exposure helps form a Zn₃N₂ layer, which possesses inversion symmetry and inverts the crystal from anion polar to cation polar.     

Methacryloxyethyl phosphate‐grafted expanded polytetrafluoroethylene membranes for biomedical applications

Expanded polytetrafluoroethylene (ePTFE) membranes were modified by graft copolymerization with methacryloxyethyl phosphate (MOEP) in methanol and 2‐butanone (methyl ethyl ketone (MEK)) at ambient temperature using gamma irradiation. The effect of dose rate (0.46 and 4.6 kGy h^?1), monomer concentration (1–40 %) and solvent were studied and the modified membranes were characterized by weight increase, X‐ray photoelectron spectroscopy (XPS), Fourier transform infrared spectroscopy (FTIR) and scanning electron microscopy (SEM). XPS was used to determine the % degree of surface coverage using the C? F (ePTFE membrane) and the C? C (MOEP graft copolymer) peaks. Grafting yield, as well as surface coverage, were found to increase with increasing monomer concentration and were significantly higher for samples grafted in MEK than in methanol solution. SEM images showed distinctly different surface morphologies for the membranes grafted in methanol (smooth) and MEK (globular), hence indicating phase separation of the homopolymer in MEK. We propose that in our system, the non‐solvent properties of MEK for the homopolymer play a more important role than solvent chain transfer reactions in determining grafting outcomes. Copyright © 2005 Society of Chemical Industry     

Ru-catalyzed anode materials for direct hydrocarbon SOFCs

A solid oxide fuel cell using a thin ceria-based electrolyte film with a Ru-catalyzed anode was directly operated on hydrocarbons, including methane, ethane, and propane, at 600 °C. The role of the Ru catalyst in the anode reaction was to promote the reforming reaction of the unreacted hydrocarbons by the produced steam and CO₂, which avoided interference from steam and CO₂ in the gas-phase diffusion of the fuels. The resulting peak power density reached 750 mW cm⁻² with dry methane, which was comparable to the peak power density of 769 mW cm⁻² with wet (2.9 vol.% H₂O) hydrogen. More important was the fact that the cell performance was maintained at a high level regardless of the change in the methane utilization from 12 to 46% but was significantly reduced by increasing the hydrogen utilization from 13 to 42%. While the anodic reaction of hydrogen was controlled by the slow gas diffusion, the anodic reaction of methane was not subject to the onset of such a gas-diffusion process.