Operational aspects of adsorption air‐conditioner used in diesel locomotive

A locomotive cabin adsorption air‐conditioner has been equipped in #DF4B‐2369 locomotive; and has been successfully run for 2 years. It is powered by waste heat from the exhaust of the diesel engine. The influence on heat transfer is described by the equivalent heat transfer coefficient or thermal resistance of components inside the adsorber. The variation of adsorption capacity is expressed by a non‐equilibrium adsorption function. The dynamic heat transfer process of adsorption air‐conditioning system is treated with the lumped parameter method. Some typical running experimental results are present. The diesel engine rotating speed and locomotive speed influenced on the refrigeration system are discussed. The maximum mean refrigeration power is regarded as an objective function. Based on experiments and theoretical analysis, the running characteristics of the air‐conditioning system are optimized. Some techniques of performance improvement are suggested as well. Copyright © 2006 John Wiley & Sons, Ltd.     

A new Pd-oxide-Al/sub 0.3/Ga/sub 0.7/As MOS hydrogen sensor

A new and interesting Pd-oxide-Al/sub 0.3/Ga/sub 0.7/As MOS hydrogen sensor has been fabricated and studied. The steady-state and transient responses with different hydrogen concentrations has been measured at various temperatures. Based on the large Schottky barrier height and presence of oxide layer, the studied device exhibits a high hydrogen detection sensitivity and wide temperature operating regime. The studied device exhibits the low-leakage current and obvious current changes when exposed to hydrogen-contained gas. Even at room temperature, a very high hydrogen detection sensitivity of 155.9 is obtained when a 9090 ppm H/sub 2//air gas is introduced. Furthermore, when exposed to hydrogen-contained gas at 95/spl deg/C, both the forward and reverse currents are substantially increased with increased hydrogen concentration. In other words, the studied device can be used as a hydrogen sensor under the applied bidirectional bias. Under the applied voltage of 0.35 V and 9090 ppm H/sub 2//air hydrogen ambient, a fast adsorption response time about 10 s is found. The transient and steady-state characteristics of hydrogen adsorption are also investigated.     

合成己二腈反应技术研究——(Ⅴ)己二腈工业反应过程模拟与反应器改造

对己二腈工业反应器提出了两釜串联带回流的模型,通过模拟计算得出模型的级间返混系数 f=6的结论。该模型能较好地预测工业反应器中物料组分浓度变化和气、液两相的流动特性;指出了现工业反应器的鼓泡中和段体积偏小是造成己二酸浓度偏高的关键;提出了可以通过增加串连一个鼓泡预反应段的改造方案,能有效地降低己二酸的浓度,从7%降至4%左右,从而能较好地减缓腐蚀和结焦。     

Kinetics of two-step anionic polymerization

This article deals with the kinetics of two-step anionic polymerization by way of a non-steady state method. Several molecular parameters can be evaluated using the formulae developed. A bimodal molecular weight distribution function for the resulting polymer is derived from the set of kinetic differential equations, which is in agreement with the experimental data reported.     

Improvement in hydrolytic procedure for GLC determination of non-indolyl glucosinolates in rapeseed as isothiocyanates

Some methods determine the non-indolyl glucosinolates content in rapeseed as their hydrolysates: the isothiocyanates and the oxazolidinethiones. These methods in their present form underestimate the amount of the glucosinolates content. In this investigation, a modified method was developed to give a better quantitative estimate, indicating a glucosinolate level five times that obtained by a typical existing method.     

Influence of ethyl methacrylate content on the volume‐phase transition of temperature‐sensitive poly[(N‐isopropylacrylamide)‐co‐(ethyl methacrylate)] microgels

A novel series of temperature‐sensitive poly[(N‐isopropylacrylamide)‐co‐(ethyl methacrylate)] (p(NIPAM‐co‐EMA)) microgels was prepared by the surfactant‐free radical polymerization of N‐isopropylacrylamide (NIPAM) with ethyl methacrylate (EMA). The shape, size dispersity and volume‐phase transition behavior of the microgels were investigated by transmission electron microscopy (TEM), ultraviolet–visible (UV–Vis) spectroscopy, dynamic light scattering (DLS) and differential scanning calorimetry (DSC). The transmission electron micrographs and DLS results showed that microgels with narrow distributions were prepared. It was shown from UV–Vis, DLS and DSC measurements that the volume‐phase transition temperature (VPTT) of the p(NIPAM‐co‐EMA) microgels decreased with increasing incorporation of EMA, but the temperature‐sensitivity was impaired when more EMA was incorporated, causing the volume‐phase transition of the microgels to become more continuous. It is noteworthy that incorporation of moderate amounts of EMA could not only lower the VPTT but also enhance the temperature‐sensitivity of the microgels. The reason for this phenomenon could be attributed to changes in the complicated interactions between the various molecules. Copyright © 2004 Society of Chemical Industry     

Structure and properties of CE/CTBN/EP blends: II. Effect of EP on the mechanical properties and thermostability of the CE/CTBN system

Carboxyl‐terminated butadiene‐acrylonitrile rubber (CTBN) has often been used to improve the toughness of cyanate ester (CE) resin while sacrificing modulus and thermostability. In this paper, the addition of the appropriate amount of epoxy resin (EP) to the CE/CTBN system is shown to not only increase the modulus and thermostability of the blend, but also improve the toughness. The values of impact strength showed a maximum for the CE/CTBN/EP 100/5/5 blend. The temperature of 10 % weight loss (T₁₀) improves from 376 °C for CE/CTBN 100/5 to 407 °C for the CE/CTBN/EP 100/5/2.5 blend. It is proposed that addition of the appropriate amount of EP can decrease the mobility and increase the stability of CTBN via the reaction between the terminal carboxyl group of CTBN and the hydroxyl group of EP. But a very high EP concentration will decrease the crosslinking density of CE, consequently reducing the mechanical properties and thermostability of the blends. Copyright © 2004 Society of Chemical Industry     

改性生物质作为型煤黏结剂的研究

探讨了用NaOH改性生物质秸秆作为型煤黏结剂的可行性,考察了NaOH溶液浓度对生物质改性的影响以及生物质添加量、无机物(MgO和MgCl2)添加量对型煤机械强度、防水性能和着火温度的影响。研究结果表明,NaOH改性液的质量分数为1.0%~2.0%时,制得的生物质型煤有较高的机械强度;生物质添加量在2%~20%时,随生物质添加量的增加,机械强度增加,着火温度降低,但防水性较差;而在生物质型煤中加入适量无机黏结剂后,型煤有很高的浸水强度,表现出优越的防水性能。