60m高度处单片露天超高混凝土悬臂墙的设计与施工

通过采用竖向预应力技术 ,解决了 60m高度处单片 8m高悬臂钢筋混凝土墙根部裂缝宽度超过规范限值的问题 ;采用将预应力钢绞线顶端锚固于墙高中段等结构和施工措施 ,控制墙体长细比不超过 3 0 ,减少了由于长细比过大对墙体承载力的不利影响     

人支气管上皮靶细胞形态学参数的测量

支气管上皮靶细胞形态学参数对计算受氡子体照射的支气管的剂量是很重要的。本文介绍利用奥尔新兰-PAS 染色的外科切除人肺组织切片,测量基底细胞粘液细胞和的胞核深度与数目。结果表明,叶、段和小支气管的粘液细胞核深度分别为相应节段基底细胞的61%、69%和73%;此三节段粘液细胞的数目分别为基底细胞的53%、29%和28%,平均为37%。     

Stable Oxygen and Carbon Isotopic Compositions of Lates stappersii Otoliths from Lake Tanganyika,East Africa

In this study, we measured growth trends in oxygen and carbon isotopic ratios in whole sagittal otoliths from three adult centropomid fish (Lates stappersii) from each of three sub-basins of Lake Tanganyika, East Africa. Sampling density was 20 to 50 samples per otolith. Both δ¹⁸O and δ¹³C values increase with age. The δ¹⁸O data suggest that otoliths were precipitated near the expected equilibrium with the ambient environment (ca. +3.5‰) and support a migration pattern from surface waters during larval stages to deeper waters (40 to 80 m) for mature fish. Relatively high δ¹⁸O values in the southern sub-basin are consistent with cooler temperatures in the region during seasonal upwelling. The δ13C increase from otolith core to edge is large (up to 4‰) and is interpreted as due to ontogenetic changes in diet and contributions from a decrease in the proportion of respired CO₂ incorporated into otolith carbonate as metabolic rates of the fish dropped with maturity. The data seem to successfully reveal life strategy and migration patterns of L. stappersii, document regional differences in lake conditions, and provide a record of temperature within the water column during which the fish lived. Higher resolution studies and analyses of historical samples could be used to constrain modern and past growth patterns, and to reconstruct past temperature gradients and productivity patterns in the lake.     

Performance of a non‐load‐bearing steel stud gypsum board wall assembly: Experiments and modelling

A gypsum wall assembly was exposed to an intense real‐scale compartment fire. For the wall assembly, temperatures were measured at the exposed face, within the stud cavity, and at the unexposed face during the fire exposure. Total heat flux gauges were used to measure the temporal variation of the energy incident on the walls, and cameras, both visual and infrared, were used to image the unexposed face of the wall assembly during the fire exposure. The behaviour of the wall assembly under the fire load is discussed as are current model results for a simulation of the fire test. Copyright © 2006 John Wiley & Sons, Ltd.     

Improvement of levitation characteristics in a magnetic bearing system using HTSC‐permanent magnet hybrid structure

Magnetic bearing using pinning force of a permanent magnet and a high‐temperature superconductor has been developed. Additional permanent magnet is introduced to increase the levitation force of the magnetic bearing. In this hybrid magnetic bearing system, levitation force is mainly given by the repulsive force of the permanent magnets, and stability for the lateral direction is given by pinning force of the superconductor. The experimental device is developed. A ring‐type superconductor and a bulk one are examined. Levitation characteristics of the hybrid magnetic bearing are measured. The bulk superconductor shows better characteristics of both levitation and lateral stability than the ring one. Levitation force of the hybrid system becomes about twice as large as that of the nonhybrid one. Although, the repulsive force of the permanent magnet decreases the lateral stability of the system, its influence becomes small by choosing an adequate position of the permanent magnets and the superconductor. © 2004 Wiley Periodicals, Inc. Electr Eng Jpn, 150(1): 71–77, 2005; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.10350     

线缆护套材料在我国西部环境中的试验研究

本文通过对线缆外护套材料在我国西部地区严酷环境试验站中土壤和大气1～5年的试验结果分析，总结了塑料护套材料的耐蚀性能。为线缆护套的防护设计、合理选材及制定标准提供科学依据。     

棕刚玉粉中Al2O3含量分析方法的探讨

对耐火材料——棕刚玉粉的质量分析控制，提出了用实用性的检测方法测定其Al2O3含量。通过与国家标准分析方法的对比试验，证实快速实用分析方法测定棕刚玉粉中Al2O3含量是可行的。     

锌基合金模具的应用及探讨

本文分析了锌基合金模具制造及使用过程中容易出现热裂、翘曲、收缩的问题，并提出了解决这些问题的措施。