Quasi-static compressive behaviour of aluminium cenosphere syntactic foams

In this paper, cenosphere particles embedded in AA2014 aluminium matrix are used to fabricate syntactic foam by stir casting method. The particle size is about 100?µm and foam density is about 1990?kg?m^?3. Compression tests at strain rate 0.001/s are performed on foam samples to characterise their mechanical properties which are then used in numerical analysis on commercial finite element analysis software ABAQUS/CAE with isotropic elastic-plastic material model. Experimental and numerical results show good conformity in deformation behaviour with elastic and plateau zones showing average deviations less than 5% and 20%, respectively. Foams showed high yield stress and energy absorption capabilities that can be useful in making blast and impact resistant structures.     

某矿快速掘进最优炮孔间距的选择

山西某矿5308底抽巷在掘进过程中速度慢、效率低，直接影响工作面的瓦斯抽采，为了改善上述情形，对炮孔间距进行研究。通过使用ANSYS软件对不同炮孔间距下快速掘进效果的模拟分析，并经现场验证，得出了适应该矿的最佳炮孔间距。结果表明：炮孔间距为500 mm时，爆破产生裂隙发育范围和岩石损伤区域都最大，快速掘进的效果最好。     

结合优化支持向量机与K-means++的工控系统入侵检测方法

针对工业控制系统传统单一检测算法模型对不同攻击类型检测率和检测速度不佳的问题，提出一种优化支持向量机和K-means++算法结合的入侵检测模型。首先利用主成分分析法（PCA）对原始数据集进行预处理，消除其相关性；其次在粒子群优化（PSO）算法的基础上加入自适应变异过程避免在训练的过程中陷入局部最优解；然后利用自适应变异粒子群优化（AMPSO）算法优化支持向量机的核函数和惩罚参数；最后利用密度中心法改进K-means算法与优化后的支持向量机组合成入侵检测模型，从而实现工业控制系统的异常检测。实验结果表明，所提方法在检测速度和对各类攻击的检测率上得到明显提升。     

Design of disturbance observer based on adaptive-neural control for large-scale time-delay systems in the presence of actuator fault and unknown dead zone

This article presents an adaptive neural compensation scheme for a class of large-scale time delay nonlinear systems in the presence of unknown dead zone, external disturbances, and actuator faults. In this article, the quadratic Lyapunov–Krasovskii functionals are introduced to tackle the system delays. The unknown functions of the system are estimated by using radial basis function neural networks. Furthermore, a disturbance observer is developed to approximate the external disturbances. The proposed adaptive neural compensation control method is constructed by utilizing a backstepping technique. The boundedness of all the closed-loop signals is guaranteed via Lyapunov analysis and the tracking errors are proved to converge to a small neighborhood of the origin. Simulation results are provided to illustrate the effectiveness of the proposed control approach.     

电磁精细探测法在隐伏型导水地质裂缝勘探中的应用

针对传统隐伏型导水地质裂缝勘探方法存在勘测精度较差的问题,提出电磁精细探测法探析隐伏型导水地质裂缝。依照屏蔽系数、实测场强和理论场强数据绘制综合曲线图,通过该图获取隐伏型导水地质裂缝所处位置几何阴影范围,采用层析成像法得到网格化的工作面,获取隐伏型导水地质图像。通过图像直接观测隐伏型导水地质工作面裂缝所处位置,在此基础上,观测四个电磁场分量,采用正交电磁场分量计算介质视电阻率,依据计算视电阻率数值和视电阻率分布状态研究裂缝发育情况和裂缝富水程度。结果表明:采用该方法能较为精准地获取隐伏型导水地质裂缝位置。通过裂缝位置进一步检测出隐伏型导水地质裂缝最大发育高度为63.5 m。当视电阻数值不断增加时,隐伏型导水地质裂缝和裂缝富水性逐渐减小,与实际情况较为相符,说明该种方法探析效果较好。     

Investigation on the effectiveness of the repair method 8.3 “Corrosion protection by increasing the electrical resistivity” in chloride-containing concrete Part 2: Chloride redistribution in concrete after application of a system sealing surface protective coating

This DFG-funded research project aimed to gain a better understanding of the mechanisms of the W-Cl repair principle within the framework of fundamental investigations, to contribute to the creation of the necessary basis for a broader application of the repair principle in practice. The focus was on the development of a model to describe the chloride redistribution after the application of a system sealing surface protective coating. On the basis of Fick's second law of diffusion, a mathematical model with a self-contained analytical solution was developed, with the help of which the chloride redistribution after application of a system sealing surface protective coating can be calculated under the idealized assumption of complete water saturation of the concrete. Furthermore, the influence of the dehydration of the concrete, expected as a result of the application of the repair principle W-Cl, on the chloride redistribution was investigated. On the basis of laboratory tests and numerical simulations, material-specific reduction functions were developed to quantify the relationship between the chloride diffusion coefficient and the ambient humidity.     

The World robot summit disaster robotics category – achievements of the 2018 preliminary competition

The World Robot Summit is a robot Olympics and aims to be held in a different country every four years from 2020. The concept of the Plant Disaster Prevention challenge is daily inspections, checks, and emergency response in industrial plants, and in this competition, robots must carry out these types of missions in a mock-up plant. The concept of the Tunnel Disaster Response and Recovery challenge is emergency response to tunnel disasters, and is a simulation competition whereby teams compete to show their ability to deal with disasters, by collecting information and removing debris. The Standard Disaster Robotics challenge assesses, in the form of a contest, the standard performance levels of a robot that are necessary for disaster prevention and emergency response. The World Robot Summit Preliminary Competition was held at Tokyo Big Sight in October 2018, and 36 teams participated in the Disaster Robotics Category. UGVs and UAVs contended the merits of new technology for solving complex problems, using core technologies such as mobility, sensing, recognition, performing operations, human interface, autonomous intelligence etc., as well as system integration and implementation of strategies for completing missions, gaining high-level results.     

黄浦江下游吴淞口站低潮位重现期研究

黄浦江为感潮河流,低潮位重现期的确定对黄浦江航道的设计具有重要意义。为了准确估计黄浦江低潮位的重现期,以黄浦江下游吴淞口站年最低潮位序列为例,在对样本进行三性审查的基础上,分别采用传统的数理统计方法和时变矩方法进行水文频率分析。结果表明:吴淞口站年最低潮位序列在1996年发生了变异;还现修正后的序列服从位置参数线性时变的GEV模型,低潮位存在缓慢的上升趋势;一致性条件下百年一遇低潮位约为0.261 m,在非一致性条件下其重现期增大为150 a。非一致性条件下的重现期增大说明黄浦江现有的航道设计标准偏安全,航道通航保证率提高。     

A design of experiments investigation into dry separation using a Knelson Concentrator

Enhanced gravity, or centrifugal, separators have revolutionised gold processing over the past decades, significantly increasing the recovery of fine (−100 μm) free gold. One of the main drawbacks of centrifugal gravity concentrators is the large volume of water required (even if it is all recycled). With water becoming an ever increasingly important “commodity”, reducing this is of importance both from an environmental and a monetary point of view. This work investigated operating a laboratory scale Knelson Concentrator with a dry feed and using air as the fluidising medium. The feed used was a synthetic mixture of tungsten and quartz, used to mimic a gold ore. The response surface method and central composite design techniques were used to design the experiments and to model the results, with the experimental variables being the bowl speed (G-Level), air fluidising pressure and the feed rate. The models corresponded well to the experimental results, indicating that for this experimental setup, the optimal conditions were a bowl G-Level of 40 G, a feed rate of 220 g/min and an air fluidising pressure of 8 psi.