3D velocity from 3D Doppler radial velocity

We present local least squares and regularization frameworks for computing 3D velocity (3D optical flow) from 3D radial velocity measured by a Doppler radar. We demonstrate the performance of our algorithms quantitatively on synthetic radial velocity data and qualitatively on real radial velocity data, obtained from the Doppler radar at Kurnell Radar station, Botany Bay, New South Wales, Australia. Radial velocity can be used to predict the future positions of storms in sequences of Doppler radar datasets.© 2005 Wiley Periodicals, Inc. Int J Imaging Syst Technol, 15, 189–198, 2005     

A load dispatch method using fractional programming and semidefinite programming

This paper describes a load dispatch method which minimizes power cost—[fuel cost]/[electric output]—for a power system with thermal plants and energy storage facilities. The proposed method employs fractional programming to convert a minimization problem with fractional objective function to a series of quadratic minimization problems, and semidefinite programming to solve converted problems. The method provides the optimum time‐dependent power output/input and storage level of energy storage facilities as well as time‐dependent power output of thermal plants. The method has been applied to a power system with five thermal plants, two energy storage facilities of various performances, and five load demands. The optimum load scheme of four time mesh points is obtained for the thermal plants and energy storage facilities. The fractional programming successfully converges the optimal scheme through a few iterations. The semidefinite programming deals with a variable matrix of 164 dimensions, and 185 inequality constraints. © 2001 Scripta Technica, Electr Eng Jpn, 138(2): 49–58, 2002     

Effect of crack-growth mechanism on the prediction of fracture load of adhesive joints

This paper presents observations regarding the cracking behavior of tensile-loaded structural adhesive joints. Experiments showed that fracture occurred by the development and propagation of a damage zone, rather than a single, sharp crack, and that the presence of the adhesive spew fillet did not affect the fracture load of the adhesive joints studied. For joints bonded with the mineral-filled epoxy Cybond 4523GB (American Cyanamid), there was approximately 5 mm of subcritical crack propagation prior to final fracture. Fracture-load predictions based on the initial uncracked geometry made in previous papers were unaffected by this small change in geometry. For joints bonded with the rubber-toughened epoxy Permabond ESP 310, approximately 50 mm of subcritical crack propagation was observed. It was again found that predictions made in previous papers on the basis of the initial geometry gave a good estimate of the final fracture load even though this subcritical crack propagation significantly altered the geometry, and thus the applied energy release rates. The effect of shear deformations of the adherends was also investigated, and it was found that shear deformations could be neglected in engineering calculations for joints subject to remote tensile loading.     

紧凑 Tokamak(球形环)聚变堆第一壁及中心导体柱上中子负荷及核热计算与分析

采用通用蒙特卡罗粒子输运程序ＭＣＮＰ／３８计算低环径比Ｔｏｋａｍａｋ（紧凑环或球形环）聚变堆第一壁及中心导体上的中子壁负荷分布和核热沉积分布，并与常规Ｔｏｋａｍａｋ堆第一壁上中子壁负荷分布和核热沉积分布进行比较、分析。结果表明，在中子壁负荷归一化为１ＭＷ／ｍ２时，与常规Ｔｏｋａｍａｋ相比，在低环径比Ｔｏｋａｍａｋ堆第一壁及中心柱表面上中子壁负荷分布峰值并不比常规Ｔｏｋａｍａｋ堆第一壁上的峰值高，而且低于低环径比Ｔｏｋａｍａｋ堆整个第一壁上的平均值，而中心柱上的核热沉积峰值稍高于常规Ｔｏｋａｍａｋ堆第一壁上的核热沉积峰值，但对较高中子壁负荷情况，中心导体柱上的核热沉积和辐照损伤仍可能是比较严重和值得特别研究的问题。     

Multiobjective dynamic load-dispatching method for optimal operation of power systems

A new practical method is proposed which gives a quasi-optimal solution of the dynamic load-dispatching problem formulated by a multiconstraint multiobjective optimization problem. Here, the multiple constraints are rate reserve constraints and power flow ones, and the multiple objectives are fuel cost and CO₂ emission. The proposed method is an integration of the following three techniques: (1) “Group Dispatch Scheme,” which is developed by the authors, is used to satisfy a violated constraint easily. This scheme consists of three steps. The first step is to classify all generators into two groups. One is the group which should be more loaded to satisfy the violated constraint, and the other is the should-be less loaded group. The second step is to add some load to the former group, and to subtract the same load from the latter. The third step is to dispatch each group load to each groups generators, respectively; (2) the dynamic load-dispatching algorithm is used which provides, in practical time, quasi-optimal generation trajectories; (3) the conventional weighting parametric method is used to obtain a Pareto optimal solution of multiobjective problems. The effectiveness of the method is clarified by a computer simulation on the actual power system of Kansai Electric Power Company.     

The pulse distributed file system

A network of powerful personal computers, linked by a high-speed local area network, is being seen increasingly as an alternative to a traditional centralized time-sharing operating system. The PULSE project is investigating how such a system may be constructed to give the benefits of a self-sufficient personal computer to each user without losing the facilities for communication and sharing of data inherent in centralized systems. In particular, a distributed file system has been built which provides a single global UNIX

1 UNIX is a trademark of Bell Laboratories.

-like hierarchy, with a consistent appearance when accessed from any machine. Replicated copies of files are maintained to improve reliability, increase performance, and enable each machine to run stand-alone, albeit with reduced facilities.     

利用ADCP回波强度估算河流悬移质含沙量的应用研究

通过简要介绍利用声学多普勒水流剖面仪(ADCP)回波强度估算悬移质含沙量的基本原理,结合梧州水文站的应用实例,利用ADCP的回波强度数据和现场采集的水样含沙量建立相关关系,根据相关关系由回波强度反演估算的水体悬移质含沙量验证了利用ADCP的回波强度估算悬移质含沙量的可行性。应用于梧州水文站的实践表明,左河道推算的系统误差为-0.1%,右河道推算的系统误差为1.5%。这种方法具有不扰动流场、测量剖面同步性较好、数据空间分辨率较高的优点,与传统的取样过滤称量法相比,计算效率显著提高。     

汽轮发电机组负荷波动的原因分析及解决措施

详细分析了汽轮发电机组在运行过程中出现电负荷波动和瞬间突降的原因，重点介绍了如何调节、维持汽轮发电机组的经济运行以及解决电负荷波动的措施，从而保证汽轮发电机组的稳定运行。