Compensation of voltage disturbances using PEMFC supported Dynamic Voltage Restorer

The continuity of supply and quality of power are the two main significant aspects of today’s power delivery system. The Dynamic Voltage Restorer (DVR) is a series connected custom power device which improves the quality of power delivered to the consumers. This paper deals with the effectual exploitation of DVR for interconnecting the proton exchange membrane fuel cell (PEMFC) stack to the grid based on optimized proportional integral (PI) and fuzzy logic (FL) Controller. The real coded Genetic algorithm (GA) is used to optimize the PI controller parameters. The PEMFC operated boost converter is used to boost up the fuel cell output voltage to balance the DC side necessities of the voltage source converter (VSC). The proposed DVR provides balanced and unbalanced voltage sag/swell compensation, harmonic reduction as well as an active power injection to the grid. The designed method also protects the sensitive loads from source side power quality disturbances including short term interruption. In addition, the harmonic compensation performance of the proposed work is validated by comparing with the results of the H^∞ controller based DVR under medium level voltage condition. The simulation results from MATLAB/SIMULINK are discussed to prove the effectiveness of the planned method.     

A review study on titanium niobium oxide-based composite anodes for Li-ion batteries: Synthesis,structure, and performance

The growing demands for Li-ion batteries (LIBs) in the electrification revolution, require the development of advanced electrode materials. Recently, intercalating titanium niobium oxide (TNO) anode materials with the general formula of TiNb_xO_2+2.5x have received lots of attention as an alternative to graphite and Li₄Ti₅O₁₂ commercial anodes. The desirability of this family of compounds stems from their high theoretical capacities (377–402 mAh/g), high safety, high working voltage, excellent cycling stability, and significant pseudocapacitive behavior. However, the rate performance of TNO-based anodes is poor owing to their low electronic and ionic conductivities. TNO-based composites generally are prepared with two aims of enhancing the conductivity of TNO and achieving a synergic effect between the TNO and the other component of the composite. Compositing with carbon matrices, such as graphene and carbon nanotubes (CNTs) are the most studied strategy for improving the conductivity of TNO and optimizing its high-rate performance. Also, for obtaining anode materials with high capacity and high long-term stability, the composites of TNO with transition metal dichalcogenides (TMDs) materials were proposed in previous literature. In this work, a comprehensive review of the TNO-based composites as the anodes for LIBs is presented which summarizes in detail the main recent literature from their synthesis procedure, optimum synthesis parameters, and the obtained morphology/structure to their electrochemical performance as the LIBs anode. Finally, the research gaps and the future perspective are proposed.     

Effect of the thicknesses of the Al2SiO5 ion conductor on the opto-electrical properties for all-solid electrochromic devices

In this study, an all-solid-state electrochromic device (ECD) with the structure of ITO/WO₃/Al₂SiO₅/NiO_x/ITO was prepared, and the effect of the Al₂SiO₅ solid electrolyte thicknesses on the opto-electrical performance was investigated. The microstructure and surface morphology were characterized using XRD, SEM and AFM, and the surface morphology and degree of surface looseness demonstrate a significant influence on the opto-electrical properties of ECDs. The charge transfer dynamics at the solid-solid interface were characterized using EIS to obtain an ionic conductivity of 4.637 × 10^-8 S/cm. CV, CA and UV–Visible spectra were employed to record the in situ electrochemical and optical properties. The results revealed that the highest optical modulation was 44.58%, the coloring and bleaching times were 14.8 s and 3.7 s, and the highest coloring efficiency was 98.17 cm²/C, which indicates that excellent opto-electrical properties were obtained. When the thickness increases, the degree of surface dense morphology transforms, and the loose morphology is more favorable for ion conductivity, which improves the opto-electrical properties. The results in this study provide insights into the understanding of Al³⁺-based all-solid-state ECDs, which promote the exploration of new types of Al³⁺ ionic conductors for all-solid-state ECDs.     

Simulation of thermal barrier coating spallation induced by the initiation/growth/coalescence of internal crack and interfacial crack based on a real image model

In the furnace cycle test, the growth of oxide film leads to the propagation and coalescence of multiple cracks near the interface, which should be responsible for the spallation of thermal barrier coatings (TBCs). A TBC model with real interface morphology is created, and the near-interface large pore is retained. The purpose of this work is to clarify the mechanism of TBC spallation caused by successive initiation, propagation, and linkage of cracks near the interface during thermal cycle. The dynamic growth of thermally grown oxide (TGO) is carried out by applying a stress-free strain. The crack nucleation and arbitrary path propagation in YSZ and TGO are simulated by the extended finite element method (XFEM). The debonding along the YSZ/TGO/BC interface is evaluated using a surface-based cohesive behavior. The large-scale pore in YSZ near the interface can initiate a new crack. The ceramic crack can propagate to the YSZ/TGO interface, which will accelerate the interfacial damage and debonding. For the TGO/BC interface, the normal compressive stress and small shear stress at the valley hinder the further crack propagation. The growth of YSZ crack and the formation of through-TGO crack are the main causes of TBC delamination. The accelerated BC oxidation increases the lateral growth strain of TGO, which will promote crack propagation and coalescence. The optimization design proposed in this work can provide another option for developing TBC with high durability.     

Theoretical investigation of solvent effects on the selective hydrogenation of furfural over Pt(111)

It was well known that solvent effect plays a very important role in the catalytic reaction. There are many theoretical studies on the solvent effect in homogeneous catalysis while there are few theoretical studies on the solvent effect in the heterogeneous catalytic reaction and there has been no work to investigate the solvent effect on furfural transformation in heterogeneous catalysis. In the present work, both the density functional calculations and the microkinetic analysis were performed to study the selective hydrogenation of furfural over Pt(111) in the presence of methanol as well as toluene and compared with that in the gas condition. The present results indicated that the methanol can enhance the adsorption strength of furfural and other oxygen-containing reaction species due to its relatively strong polarity properties and this can be a main reason for solvent-induced high activity and selectivity. Another reason is that reaction paths study showed that the presence of methanol solvent makes the dehydrogenation of furfural less thermochemical due to the fact that furfural is more stabilized than that of dehydrogenation species, and methanol also has an inhibition effect on the dehydrogenation of furfural in the kinetic aspect, and further energetic span theory proves highest activity and selectivity for hydrogenation in methanol solvent of vapor, methanol and toluene. Moreover, microkinetic model simulation demonstrated that the activity and selectivity of hydrogenation in methanol is both higher than that in vapor and toluene. The much higher activity in methanol is due to the stabilized adsorbed reactants in the surface, which leads to a higher surface coverage of furfural. It might be proposed based on the present work that a solvent with relatively strong polarity may be favorable for the high selective hydrogenation of furfural.     

苯乳酸抑制链格孢霉作用靶位的分析

以从自然腐败的樱桃上分离的链格孢霉（Alternaria sp.）LD3.0086为指示菌，研究苯乳酸对链格孢霉的主要抑制作用靶位。应用分光光度法测定苯乳酸对链格孢霉的最小抑菌浓度，通过卡尔科弗卢尔荧光增白剂染液（calcofluor white，CFW）染色观察苯乳酸对菌丝顶端生长的破坏作用，利用扫描电子显微镜和透射电子显微镜观察链格孢霉的超微结构变化，通过测定苯乳酸作用前后链格孢霉上清液中N-乙酰葡萄糖胺质量浓度变化研究苯乳酸对菌丝细胞壁的破坏作用，应用荧光双染色法观察苯乳酸对链格孢霉菌丝细胞膜的损伤作用。结果表明，12.5 mmol/L的苯乳酸能有效抑制链格孢霉的生长；与对照组（无菌水处理）相比，苯乳酸处理后链格孢霉顶端生长细胞无明显形变，经12.5 mmol/L苯乳酸处理的链格孢霉上清液中N-乙酰葡萄糖胺质量浓度基本不变；苯乳酸处理24 h，链格孢霉菌丝细胞壁表面无明显损伤，细胞内结构发生明显变化；苯乳酸短时间（4 h）处理链格孢霉，菌丝细胞膜仍较为完整，加入苯乳酸较长时间（8 h）后细胞膜发生破裂。综合分析可知，苯乳酸对链格孢霉的主要作用靶位应不是菌丝体的细胞壁和细胞膜，而是在菌丝体内部，通过破坏菌丝内部细胞器结构或引起细胞内的生化反应，从而抑制链格孢霉的生长和繁殖，发挥抑菌活性。     

Systematic optimization of corrosion,bioactivity, and biocompatibility behaviors of calcium-phosphate plasma electrolytic oxidation (PEO) coatings on titanium substrates

To optimize the corrosion, bioactivity, and biocompatibility behaviors of plasma electrolytic oxidation (PEO) coatings on titanium substrates, the effects of five process variables including frequency, current density, duty cycle, treatment time, and electrolyte Ca/P ratio were evaluated. In our systematic study, a Taguchi design of experimental based on an L16 orthogonal array was used. For this, the coatings characteristics such as the surface roughness, wettability, rutile to anatase and Ca/P ratios, and corrosion polarization resistance were investigated. After determining the optimum process variables for each response, the apatite forming ability in SBF (bioactivity behavior) and MG63 cell attachment and flattening (biocompatibility behavior) for two groups of coatings were examined. The first group was optimized based on the maximum corrosion polarization resistance and the variables were set as the frequency of 2000 Hz, the current density of 5 A/dm², the duty cycle of 30%, the treatment time of 5 min, and the Ca/P ratio of 0.65 at. % in the electrolyte. For the second group, the maximum surface roughness, greatest Ca/P ratio, and highest wettability as well as the minimum rutile to anatase ratio in coatings, could be obtained when the variables were set as the frequency of 10 Hz, the current density of 12.5 A/dm², the duty cycle of 50%, the treatment time of 12.5 min, and the Ca/P ratio of 1.70 at. % in the electrolyte. The results showed that while both groups of coatings indicated a significant apatite forming ability and can serve as bioactive coatings, a proper attachment and flattening of cells and consequently, the favorable biocompatibility properties were seen only in the first group.     

Epos – an instrument for the assessment of the ethical position in software development

Digital technology becomes more powerful, intelligent, pervasive and ubiquitous. Ethical aspects of this development have not yet drawn the appropriate attention of researchers and engineers. This paper presents an instrument that aims at measuring the individual ethical position with regard to the design and development of computer software. The development of the Epos tool was based on two data collections. The data of the first survey (n₁ = 147 participants) were used to select items and to determine the factorial structure of the questionnaire. Results show that the Epos instrument reliably assesses peoples’ ethical opinion with respect to five central components: (1) regulation, (2) data privacy, (3) domain specific knowledge, (4) societal responsibility and (5) company responsibility. In the second survey, we determined the stability of the instruments factor structure by assessing a sample of n₂?=?196 participants. A confirmatory factor analysis (CFA) supported the initial factor structure. Next steps and further implications are discussed regarding the final version of the questionnaire.     

毒品滥用流行病模型的稳定性分析

现有毒品滥用流行病模型假设吸毒者康复后对毒品拥有永久"免疫"力，而忽视了其再次成为毒品易感者的可能性。针对这一问题，通过考虑社区治疗和隔离治疗两种措施，分析了毒品滥用人群的演化过程，提出了基于暂时"免疫"力的毒品滥用流行病模型，并计算了模型的基本再生数，讨论了模型平衡点的存在性和稳定性。当基本再生数小于1时，模型存在一个局部渐进稳定的无毒平衡点；当基本再生数大于1时，模型存在唯一的地方病平衡点，并利用几何方法证明了地方病平衡点的全局稳定性；当基本再生数等于1时，如果满足一定条件，模型出现后向分支现象。数值模拟验证了上述所有结果。研究结果表明提高隔离治疗率、改善社区治疗效果和降低接触传染率可以有效抑制毒品滥用的流行。     

Effect of steel slag on 3D concrete printing of geopolymer with quaternary binders

A new type of 3D-printable ‘one-part’ geopolymer was synthesized with fly ash (FA), granulated blast furnace slag (GBFS), steel slag (SS) and flue gas desulfurization gypsum (FGD). The effects of SS content (0–40%) on the rheological properties, 3D-printability, mechanical anisotropy and reaction kinetics of geopolymer were investigated. The yield stress and plastic viscosity monotonically decreased with the increasing SS content. Contrarily, the geopolymer with 10% of SS presented better extrudability, buildability and mechanical strength than those with 0, 20%, 30% and 40% of SS. This was mainly attributed to the conflicting influence of SS on geopolymerization, of which the OH^? produced by hydration of SS raised the alkalinity of the reaction system and accelerated the dissolution of SiO₄^4? and AlO₄^5?, while the low reactivity prohibited the following polymerization process. Furthermore, the 3D-printed geopolymer presented more compact microstructure and less mechanical anisotropy thanks to the crosslinking of morphologically complementary products, including N(C)-A-S-H, C–S–H, AFt and CH, formed via synergistic reaction of FA-GBFS-SS-FGD system.