Practical method for generation expansion planning based on dynamic programming

This paper presents an efficient method which provides the optimal generation mix and the optimal generation construction process. The approximation method in which the dynamic programming technique and gradient method are combined is applied to determine the optimal generation mix with hydropower generation technologies. The successive approximations dynamic programming (SADP) technique, which is very suitable for high-dimensional multistage decision process problems, is used for obtaining the optimal generation construction process. The effectiveness and feasibility of the developed technique are demonstrated on a practical power system model which has five types of generation technologies including a hydropower generation technology.     

Improvement of levitation characteristics in a magnetic bearing system using HTSC‐permanent magnet hybrid structure

Magnetic bearing using pinning force of a permanent magnet and a high‐temperature superconductor has been developed. Additional permanent magnet is introduced to increase the levitation force of the magnetic bearing. In this hybrid magnetic bearing system, levitation force is mainly given by the repulsive force of the permanent magnets, and stability for the lateral direction is given by pinning force of the superconductor. The experimental device is developed. A ring‐type superconductor and a bulk one are examined. Levitation characteristics of the hybrid magnetic bearing are measured. The bulk superconductor shows better characteristics of both levitation and lateral stability than the ring one. Levitation force of the hybrid system becomes about twice as large as that of the nonhybrid one. Although, the repulsive force of the permanent magnet decreases the lateral stability of the system, its influence becomes small by choosing an adequate position of the permanent magnets and the superconductor. © 2004 Wiley Periodicals, Inc. Electr Eng Jpn, 150(1): 71–77, 2005; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.10350     

Steady-state torque control system with secondary-current feedback for three-phase squirrel-cage induction motors

This paper presents a highly stable steady-state torque control system with a feedback of a secondary current signal. The torque control system is constructed with a feedback of the secondary current (I₂) signal using a quick response magnetic-field sensor constructed with an amorphous core multivibrator bridge, which can solve the secondary resistance change problem for temperature variation in the IM. Moreover, we added a state feedback to the system to improve the response speed for the unit step function of a torque order. The I₂ sensor method has advantages especially at a low-speed range, in which conventional method using an integrator shows control errors.     

Transient analysis of an advanced static var compensator using quad-series voltage-source PAM inverters

This paper deals with an advanced static Var compensator (ASVC) using quad-series voltage-source PAM inverters. The ASVC consists of four three-phase voltage-source inverters with a common dc capacitor and four three-phase transformers, each primary winding of which is connected in series with each other. Each inverter outputs a square-wave voltage, while the synthesized output voltage of the ASVC has a 24-step wave shape. This results not only in a great reduction of harmonic currents and dc voltage ripples but also in fewer switching and snubbing losses. In this paper, transient analysis is performed with the focus on the response of reactive power and the resonance between the dc capacitor and ac reactors. Experimental results obtained from a small-rated laboratory model of 10 kVA are also shown to verify analytical results based on the p-q transformation. The analytical results help in the design of system parameters such as the capacity of the dc capacitor and feedback gains.     

Influence of two-step process and of different stoichiometric ratios on morphologies generated in castor oil epoxy resins

Phase separation during polymerization was studied in a model system consisting of a diepoxide based on diglycidyl ether of bisphenol A (DGEBA), variable amounts of ethylenediamine (EDA) and the mass of castor oil (CO) necessary to obtain a mass fraction equal to 0-15 in a final system where the stoichiometric ratio of amine to epoxy equivalents, r, was equal to 1. A two-step polymerization process was performed by curing first a system with r = 0-5, during variable times before phase separation, and then carrying the system to r = 1. Thermodynamic analysis of samples with different r values led to a linear relationship between the Flory-Huggins interaction parameter and r. The concentration (P) and average size (D?) of dispersed-phase particles followed opposite trends, i.e. P increased while D? decreased, when either r was increased or the time of curing in the first step of a two-step process was decreased. This was explained by assuming that the competition between nucleation and growth was determined by the viscosity at the cloud point, η_cp. Low values of η_cp favoured growth over nucleation and led to fewer but larger particles.     

Hierarchical intelligent control with flexible AC transmission systems application

A novel hierarchical intelligent controller configuration is proposed using an artificial neural network as a control-mode classifier in the supervisory level and a set of pre-designed controllers in the lower level. Controller outputs are modified nonlinearly by the classifying signals in a structure resembling one artificial neuron with adaptively changed weights. The lower-level local controllers are implemented using neural networks. An illustrative example of this approach is based on the transient stabilization of a single-machine infinite-bus system studied in Flexible AC Transmission Systems (FACTS) research.     

Optimal task allocation in hypercube multiprocessor ensembles

Criteria are established to determine the optimal policy for allocating a set of uniform tasks onto a multiprocessor hypercube ensemble. It is shown that the optimal policy depends on the ratio of computation to intertask communication required by the distributed program, and that based on this ratio, tasks should be placed either all on one processor or uniformly distributed over the largest possible hypercube.     

Air Filtration and Radon Decay Product Mitigation

Air cleaning as a means of mitigating the risks arising from exposure to indoor radon progeny has been evaluated in a single-family house in the north eastem US. using an automated, semi-continuous activity-weighted size distribution measurement system. The measurements included radon concentration, condensation nuclei count, and activity-weighted size distribution of radon decay products. Measurements were made in the house with and without an operating air filtration system and with various particle sources common to normal indoor activities operating. Aerosols were generated by running water in a shower, candle burning, cigarette smoking, vacuuming, opening doors, and cooking. Using a room model, the changes in attachment rates, average attachment diameters, and deposition rates of the unattached fraction with and without the air cleaning system were calculated. In the presence of active aerosol sources, the air filtration unit typically reduced the concentration of particles within the hour following the end of particle generation. After candle burning, cigarette smoking, and vacuuming in the bedroom, the reductions of PAEC by air filtration are about 60% with the air filtration system operating in the bedroom. During cooking in the kitchen, the reductions of PAEC in the bedroom with the air filtration system were about 40%. However, for all cases the dose reductions were smaller than the particle and PAEC reductions. For those particles that were generated within the bedroom, there was a 20% to 50% reduction in dose. In the case of cooking where the door was open and particles infiltrated from the rest of the house, the dose reduction was only 5% on average and appears to be insignificant. Thus, the dose reductions were h e r than the reductions in activity concentration, but there were no cases where the estimated dose actually increased.     

层状催化剂颗粒的优化设计——双组分等温平行反应体系

针对双组分等温平行反应体系,分析讨论了以提高催化剂活性和选择性为目标时催化剂活性组分的最优分布形式(为δ-函数分布),并给出了确定这种反应体系的催化剂的最佳活性层位置的计算方法。结果表明:以提高选择性为目标的最佳活性层位置比以提高活性为目标的要更靠近催化剂核心,实用的最优位置应介于二者之间。最后,本文还研究了反应动力学级数、本性选择性以及内扩散模数(Thiele 模数)等因素对最佳活性层位置的影响。