Transmittance and cathodoluminescence of AlN ceramics sintered with Ca3Al2O6 as sintering additive

Aluminum nitride ceramics were prepared by sintering with 0–4.8 mass% of Ca₃Al₂O₆ (C₃A) as a sintering additive. The transmittance in the range of 260–550 nm increased with increasing amount of C₃A. The cathodoluminescence intensity attributed to oxygen-induced defects decreased with increasing amount of C₃A. From the results, the increase of the transmittance in the range of 260–550 nm was considered to be related to the decrease of the oxygen-induced defect density.     

Hydrothermal Reaction Mechanism and Pathway for the Formation of K2Ti6O13 Nanowires

Calculations and detailed first principle and thermodynamic analyses have been performed to understand the formation mechanism of K₂Ti₆O₁₃ nanowires (NWs) by a hydrothermal reaction between bulk Na₂Ti₃O₇ crystals and a KOH solution. It is found that direct ion exchange between K⁺ and Na⁺ plus H⁺ interactions with [TiO₆] octahedra in Na₂Ti₃O₇ promote the formation of an intermediate H₂K₂Ti₆O₁₄ phase. The large lattice mismatch between this intermediate phase and the bulk Na₂Ti₃O₇ structure, and the large energy reduction associated with the formation of this intermediate phase, drive the splitting of the bulk crystal into H₂K₂Ti₆O₁₄ NWs. However, these NWs are not stable because of large [TiO₆] octahedra distortion and are subject to a dehydration process, which results in uniform K₂Ti₆O₁₃ NWs with narrowly distributed diameters of around 10 nm.     

不同锌钛比对纳米钛酸锌（ZnO—TiO2）体系成分的影响

以工业偏钛酸、硫酸锌、氨水为主要原料，用直接沉淀法并进行热处理得到钛酸锌粉体，并用XRD对产物成分进行了检测。结果表明，不同的锌钛比对钛酸锌（ZnO-TiO2）体系的成分有较大影响。     

络合沉淀法制备BaTiO_3超细粉末

在分析ＢａＴｉＯ_３前驱体形成机理的基础上，提出了以草酸作为络合剂，用络合沉淀法制备超细ＢａＴｉＯ_３新工艺。用化学分析法测定产物Ｂａ／Ｔｉ比，用ＸＲＤ、ＴＥＭ、ＢＩ－９０激光散射粒度仪对产物的晶型、粒度及形貌进行表征。结果表明：采用该法合成的前驱体，微观组分确定，粒径小，粒度分布窄，近似球形，煅烧后为高纯超细ＢａＴｉＯ_３粉末。     

纳米材料对PBT合成的催化性能研究

用溶胶－凝胶法制备TiO2及TiO2/SiO2复合纳米材料，作为PBT（聚对苯二甲酸丁二酯）合成的催化剂，与现在普通使用的催化剂钛酸丁酯进行了比较和研究。结果发现，TiO2/SiO2复合纳米材料催化性能最好，纳米TiO2次之。     

浅议铝箔项目的给排水设计

通过铝箔项目的工程实例,详细介绍了铝箔项目给排水专业设计的主要构成,并总结了几点设计体会,可供有关专业设计人员借鉴、参考。     

升深2-17井络合铝聚合物充气钻井液现场试验

为加快徐加固子深层天然气的勘探开发步伐，缩短深层气井的建井周期，在升深2-17井进行了充气钻井试验。介绍了络合铝聚合物充气钻井液技术的现场应用概况及效果以及井漏的发生与处理过程、钻井液起泡的解决措施。在现场试验过程中，络合铝聚合物钻井液性能稳定，具有较强的抑制性和较好的流变性能，流性指数控制在0．7左右，具有良好的携屑和稳定井壁能力，而且粘度较低，基本上控制在33～52s之间，满足了现场充气和脱气的需要；该钻井液抗温可达180℃，润滑性能较好，在钻井过程中无粘卡显示，在深井欠平衡井眼稳定方面取得了较好的效果；在不同的气液比条件下，可以在0．83～1．08g／cm。之间实现对当量密度的调节;与常规钻井工艺相比，充气钻井可以使机械钻速提高30％～50％；在钻进过程中实现了充气和点火同时进行，达到了欠平衡钻井工艺技术的要求，为进一步开展气体钻井打下了良好的基础。     

Hybrid gas-to-particle conversion and chemical vapor deposition for the production of porous alumina films

Porous alumina films can be found in a wide variety of materials, including filters, thermal insulation components, dielectrics, biomedical and catalyst supports, coatings and adsorbents. Production methods for these films are as equally diverse as their applications. In this work, a hybrid process based upon chemical vapor deposition and gas-to-particle conversion is presented as an alternative technique for producing porous alumina films, with the main advantages of solvent-free, low substrate-temperature operation. In this process, nanoparticles were produced in the vapor phase by reaction of aluminum acetylacetonate in the presence of oxygen. Downstream of this reaction zone, these nanoparticles were collected via thermophoresis onto a cooled substrate, forming a porous film. Some deposited films were subjected to post-processing in the form of annealing in air. Fourier-transform infrared spectra and X-ray energy-dispersive spectroscopy analysis confirmed the production of alumina at processing temperatures above 973 K. X-Ray diffraction revealed that the films were amorphous. Film thickness, ranging from 30 to 250 μm, and the average deposition rate were determined from scanning electron microscopy results. From transmission electron microscopy, the average primary particle size was determined to be approximately 18 nm and the formation of nanoparticle aggregates was evident. Annealing of the films at temperatures ranging from 523 to 1173 K in the presence of air did not have an effect on particle size. The specific surface area of the powder composing the films ranged from 10 to 185 m² g⁻¹, as determined from nitrogen gas adsorption by the Brunauer–Emmett–Teller method.