Evolution of grain structure in thin film reactions

In this paper, we examine, both experimentally and theoretically, the kinetics of formation and microstructure of product phases in thin film reactions, using the Nb/Al and Ti/Al systems as our prototypes. The results of calorimetry and microscopy studies are interpreted using simple kinetic and morphology models. In particular, the kinetic models employed here focus on the nucleation and growth components of the phase formation process and the morphology models provide a starting point for the classification of product grain structures. An erratum to this article is available at .     

反应离化团束（RICB）法生长CN硬质薄膜

用反应离化团束（ＲＩＣＢ）法，以低分子量聚乙烯为蒸发材料，氨气为反应气体，在ＮａＣｌ（１００）和Ｓｉ（１００）衬底上淀积Ｃ－Ｎ薄膜，透射电子衍射（ＴＥＭ）分析表明薄膜中含有β－Ｃ３Ｎ４晶粒，Ｘ射线光电子谱（ＸＰＳ）和红外吸收谱（ＩＲ）表明存在Ｃ，Ｎ原子的化学键合。     

氮化钛薄膜的高分辨AES谱和XPS谱研究

着重讨论了TiNx薄膜俄歇电子谱的定量分析方法和X射线光电子谱中线形的变化。利用已知组元强度定量分析技术和Ti的LMV俄歇电子峰，探讨TiNx薄膜中N含量的定量方法。由该方法给出的定量结果与X射线光电子谱定量结果相一致。同时，利用X射线光电子谱测定了TiN和Ti2N2p轨道的结合能。并针对Ti2p峰形随N含量的变化，给出新的解释。     

Sensitizing Mechanism and Adsorption Properties of Dye—Sensitized TiO2 Thin Films

The dye-sensitized TiO2 complex films were prepared by the dye coat onto TiO2 surfaces,and the sensitizing mechanism and adsorption properties of the dye-sensitized TiO2 complex films were inverstigated.The influence of the application conditions of dye adsorbed on TiO2 films on the amount of dye adsorption was discussed.Experimental results show that the concentration,the temperature of dye solutions and the dipping time of TiO2 films in the dye solutions have a significant influence on the amount of dye adsorption.Cell test indicates that the conversion efficiency of light to electricity increases with the amount of dye adsorption.     

Sputter deposition technology as a materials engineering

Sputter deposition is currently being widely used in the microelectronics industry for the production of silicon integrated circuits. Recently interest has been focused on sputter deposition as a new materials processing technique. The highly energetic sputtered atoms enhance crystal growth and/or sintering during film growth. This results in lowering of the growth temperature of high temperature materials including cubic diamonds. Single crystals of complex ceramics materials could be prepared by sputter deposition through epitaxial growth process. Atomically controlled deposition using multi-target sputter enables to make man-made superlattice including high-T _C superconductors of layered perovskite. At present sputter deposition is one of key materials technologies for the coming century.     

Growth and characterization of hot-wall epitaxial CdTe on (111) HgCdTe and CdZnTe substrates

Thin CdTe films were deposited by hot-wall epitaxy (HWE) on (111) HgCdTe and CdZnTe substrates at temperatures from about 140 to 335°C. X-ray rocking curves were used to show that crystal quality of the CdTe (111)B films improved as substrate temperature increased from 140 to about 250°C. Rocking curve values for full width at half maximum (FWHM) decreased from 2–4 degrees at 140–150°C to less than 100 arc-s at 250°C, and a FWHM of 59 arc-s was the lowest value observed near 250°C. The FWHM of the HWE CdTe was found to be insensitive to growth rate below about 400Å/min, but increased to four degrees at 1250Å/min. X-ray diffraction confirmed that films grown on the B-face at higher temperatures were epitaxial, but contained a significant volume fraction, 35% to 50%, of rotational in-plane twins. Electron microscopy confirmed a coarse twin density, and photoluminescence spectra showed an absence of excitonic emission in the HWE films. Simultaneous growth on two (111) HgCdTe substrates with different surface polarities between 230°C and 335°C showed that deposition rate on the A-face decreased relative to that on the B-face as temperature increased. Films grown on the B-face exhibited better surface morphologies than those grown on the A-face.     

LaCrMnNiO系热敏陶瓷的微观结构控制

通过对不同配方、工艺下的ＬａＣｒＭｎＮｉＯ系热敏陶瓷的微观结构研究，指出材料的相组成对其宏观电性能的影响，并提出了通过复合工艺利用“过渡相”的形成，对材料的“最终相”加以控制的方法。文中列出了使用ＸＲＤ及ＸＰＳ手段对材料微观结构的分析结果及有关电性能的测试数据。     

Review: Modified Atmosphere Packaging and its effects on the microbiological quality and safety of produce

Modified Atmosphere Packaging and related technologies are increasingly used to extend shelf-life of fresh produce. This paper reviews the effect of such technology on the spoilage microbiological flora and food-borne pathogens which may be present in produce and also on the organoleptic properties of the product.     

Nucleation of copper on an assembly of carbon microelectrodes

The initial stage of copper electrodeposition on the electrochemically activated assembly of carbon microelectrodes from an acid solution of copper sulfate was investigated using cyclic voltammetry, potentiostatic pulse technique and electrochemical impedance spectroscopy. Analysis of the experimental current transients has been carried out using a non-linear fitting procedure according to the model that takes into account spherical diffusion towards a disc-shaped microelectrode. The higher values of diffusion coefficient in comparison with those observed on planar electrodes were explained with an increased diffusion caused by the electrode geometry. Impedance spectra showed two time constants, the high-frequency related to the charge transfer process and the low-frequency corresponded to the deposit morphology.