Quantitative evaluation of generator power control effect of FACTS controllers for power system stabilization

The advancement of power electronics technologies has significantly developed the power system stabilizing controllers. Quantitative as well as qualitative evaluation of their effectiveness in power systems is a matter of great importance for the feasibility investigation of these apparatus. In this paper, the possible control region of FACTS controllers with series and/or shunt configuration in a single machine to infinite bus system is formulated in the powerangle curve with a set of algebraic equations. The effectiveness of TCPST (Thyristor‐Controlled Phase Shifting Transformer), SSSC (Static Synchronous Series Compensator), and TCSC (Thyristor‐Controlled Series Compensator) for the improvement of the transient stability is evaluated quantitatively as a numerical example. The correctness of the proposed method has been confirmed by analysis based on the electromagnetic transients simulation with a detailed system model. © 2001 Scripta Technica, Electr Eng Jpn, 138(3): 43–51, 2002     

Sensorless control of synchronous reluctance motors using on‐line parameter identification method not affected by position estimation accuracy

This paper presents a novel on‐line parameter identification method for sensorless control of Synchronous Reluctance Motors (SynRMs). Although conventional sensorless control methods based on mathematical models usually need some complex measurements of motor parameters in advance, the proposed identification method does not require them and can be realized on‐line. The proposed method identifies motor parameters under sensorless control, so rotor position and velocity cannot be used to identify these parameters. However, the proposed method does not need rotor position and velocity, and identified parameters are not affected by these estimation errors. The sensorless control using identified motor parameters is realized, and the effectiveness of the proposed method is verified by experimental results. © 2006 Wiley Periodicals, Inc. Electr Eng Jpn, 155(3): 62–69, 2006; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20258     

Minimum switching control for adaptive tracking

The switching adaptive control method has been used for quite a few years to solve the adaptive stabilization and model reference adaptive control problems. However, a serious problem with the switching control method is that the number of ‘candidate’ controllers can potentially be very large, especially for multi‐input–multi‐output systems. In this paper, we consider a class of minimum‐phase multi‐input–multi‐output plants with some mild compactness assumptions. Given any polynomial reference input, we provide a switching control law which guarantees exponentially stability of the closed‐loop system with exponential tracking performance. The main contribution of the paper is that we give the minimum number of candidate controllers required for switching. In particular, the number is equal to 2 for single‐input–single‐output plants (one for each sign of the high‐frequency gain), and is equal to 2^m for m‐input–m‐output plants. That is, the number is independent of the degree and the relative degree of the plant. Copyright © 2006 John Wiley & Sons, Ltd.     

A novel method of suppressing the inrush current of transformers by using a series‐connected voltage‐source PWM converter

This paper proposes a novel method of suppressing the inrush current of transformers. A small‐rated voltage‐source PWM converter is connected in series to the transformers through a matching transformer. As the connected PWM converter serves as a resistor for the source current, no inrush phenomena occurs. The required rating of the PWM converter, which serves as the damping resistor for the inrush phenomena, is 1/400 that of the main transformers in single‐phase circuits. In three‐phase circuits, it is 1/900. The basic principle of the proposed method is discussed. Digital computer simulation is implemented to confirm the validity and excellent practicability of the proposed method using the PSCAD/EMTDC. A prototype experimental model is constructed and tested. The experimental results demonstrate that the proposed method can perfectly suppress the inrush phenomena. © 2006 Wiley Periodicals, Inc. Electr Eng Jpn, 157(4): 56–65, 2006; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20174     

A novel robust current control approach using adaptive line enhancer for three‐phase current‐source active power filter

An effective system control method is presented for applying a three‐phase current‐source PWM converter with a deadbeat controller to active power filters (APFs). In the shunt‐type configuration, the APF is controlled such that the current drawn by the APF from the utility is equal to the current harmonics and reactive current required for the load. To attain the time‐optimal response of the APF supply current, a two‐dimensional deadbeat control scheme is applied to APF current control. Furthermore, in order to cancel both the delay in the two‐dimensional deadbeat control scheme and the delay in DSP control strategy, an Adaptive Line Enhancer (ALE) is introduced in order to predict the desired value three sampling periods ahead. ALE has another function of bringing robustness to the deadbeat control system. Due to the ALE, settling time is made short in a transient state. On the other hand, total harmonic distortion (THD) of source currents can be minimized compared to the case where ideal identification of the controlled system can be made. The experimental results obtained from the DSP‐based APF are also reported. The compensating ability of this APF is very high in accuracy and responsiveness although the modulation frequency is rather low. © 2004 Wiley Periodicals, Inc. Electr Eng Jpn, 150(1): 50–61, 2005; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20014     

IC—V100电台锁相环频率合成器

本文从频率合成器的结构、功能入手,详细阐述了频率编程的原理及方法。     

Neutron Stress Measurement of W‐Fiber Reinforced Cu Composite

Stress measurement methods using neutron and X‐ray diffraction were examined by comparing the surface stresses with internal stresses in the continuous tungsten‐fiber reinforced copper‐matrix composite. Surface stresses were measured by X‐ray stress measurement with the sin²ψ method. Furthermore, the sin²ψ method and the most common triaxal measurement method using Hooke's equation were employed for internal stress measurement by neutron diffraction. On the other hand, microstress distributions developed by the difference in the thermal expansion coefficients between these two phases were calculated by FEM. The weighted average strains and stresses were compared with the experimental results. The FEM results agreed with the experimental results qualitatively and confirmed the importance of the triaxial stress analysis in the neutron stress measurement.     

高功率双工旋转场移相器

旋转场移相器具有移相精度高(均方根误差可小于1°)和温度稳定性好等特点,通过改进射频传输结构,可大大提高他的功率容量。利用旋转场移相器的互易特性和铁氧体圆极化器的非互易特性,设计出高功率双工旋转场移相器。其双工特性可将收/发信号分开,实现移相器和环行器的双重功能,用于天线的收发通道等场合时,可省去一个高功率环行器,结构紧凑。分析了双工旋转场移相器的工作原理,阐述了高功率应用下的设计方法,推导出了管状铁氧体的相移量计算公式,按此方法设计了实用的器件,并给出了试验数据。     

Phase equilibria of quasi-binary systems consisting of multicomponent polymers 1 and 2. IV: Poly(ethylene oxide)/poly(propylene oxide) systems

To confirm the reliability of the theory of phase equibria of multicomponent polymer 1/multicomponent polymer 2 systems (i.e. quasi-binary systems) and the method of computer experiment based on this theory (Brit. Polym. J., 23 (1990)285; 23 (1990)299; Polym. Int., 29 (1992)219), could point curves (CPC), two-phase volume ratios ( R ) and critical solution points (CSP) have been determined experimentally for the quasi-binary mixtures of poly(ethylene oxide) (M¯_w = 647, M¯_w/M¯_n = 1.15; M¯_w and M¯_n, the weight-average and numberaverage molecular weights, respectively) and poly(propylene oxide) (M¯_w = 2028, M¯_w/M¯_n = 1.08; and M_w = 2987, M_w/M_n = 1.13). The hydroxyl end groups of both polymers were methoxylated in advance by the Cooper & Booth method (Polymer, 18 (1977)164). The thermodynamic interaction parameter between both polymers, χ₁₂, and the concentration dependence parameters for the above quasi-binary systems were determined by the method proposed in a previous paper (Brit. Polym. J., 23 (1990)299). CPC, R and CSP values calculated on the basis of the theory are in good agreement with the values determined experimentally.     

Studies on the synthesis of SAPO-5

Silicoaluminophosphate (SAPO-5) molecular sieves have been synthesised from reaction mixtures having a molar composition of: 0.7–1.0 Al₂O₃:0.7–1.0 P₂O₅:0.01–2.0 SiO₂:xR:40 H₂O (where R = (C₂H₃)₃N or (C₂H₃)₄NOH and x = 1.5–2.5 for (C₂H₅)⁵N and 0.5 for (C₂H₅)₄NOH, at 473 K using various sources of alumina and silica. The effects of (i) varying the crystallinity of the alumina source (boehmite) and (ii) the use of different silica sources such as freshly prepared silica either from sodium silicate or paddy husk extract, silica gel from commercial water-glass, and tetraethyl orthosilicate have been studied. The crystallinity of boehmite has been found to have a strong effect on its reactivity towards the formation of SAPO-5. The activity of boehmite for SAPO-5 formation increased with a decrease in its crystallinity (or with increase in its moisture content). Any silica source devoid of sodium ions could be employed for the synthesis of SAPO-5. The process of crystallisation started as early as within 1.5 h of reaction and incorporation of silicon into the AlPO₄ framework has been noted at this stage. Formation of some tridymite phase as impurity has been observed under conditions such as (i) SiO₂ concentration > 1.7 mole and (ii) x > 2.0 when R = (C²H₅)₃N.