Resilient metal spring network silicone-matrix composite for separable interconnections

Resilient metal spring silicone-matrix conducting composites for separable interconnections in electronics were fabricated by the impregnation of silicone into a preform comprising randomly oriented C-shaped Cu-Be springs and a small proportion of Sn-Pb solder, which served to connect the springs at some of their intersections. Composites containing 6.1-9.8 vol.% total filler exhibited volume electrical resistivity 0.5-1.0 mΩ.cm and contact resistivity (with copper) 11-17 mΩ.cm². A compressive stress of about 30 kPa was needed for the low contact resistivity to be reached. The volume 17-26% and the contact resistivity increased by 5% after heating in air at 130-150°C for seven days. Composites containing <9 vol.% total filler showed no stress relaxation for seven days at 6.0% strain.     

Phase equilibria of quasi-binary systems consisting of multicomponent polymers 1 and 2. IV: Poly(ethylene oxide)/poly(propylene oxide) systems

To confirm the reliability of the theory of phase equibria of multicomponent polymer 1/multicomponent polymer 2 systems (i.e. quasi-binary systems) and the method of computer experiment based on this theory (Brit. Polym. J., 23 (1990)285; 23 (1990)299; Polym. Int., 29 (1992)219), could point curves (CPC), two-phase volume ratios ( R ) and critical solution points (CSP) have been determined experimentally for the quasi-binary mixtures of poly(ethylene oxide) (M¯_w = 647, M¯_w/M¯_n = 1.15; M¯_w and M¯_n, the weight-average and numberaverage molecular weights, respectively) and poly(propylene oxide) (M¯_w = 2028, M¯_w/M¯_n = 1.08; and M_w = 2987, M_w/M_n = 1.13). The hydroxyl end groups of both polymers were methoxylated in advance by the Cooper & Booth method (Polymer, 18 (1977)164). The thermodynamic interaction parameter between both polymers, χ₁₂, and the concentration dependence parameters for the above quasi-binary systems were determined by the method proposed in a previous paper (Brit. Polym. J., 23 (1990)299). CPC, R and CSP values calculated on the basis of the theory are in good agreement with the values determined experimentally.     

Dough mixing and breadmaking properties of quinoa-wheat flour blends

Flour blends of quinoa-wheat containing 0, 5, 10, 15, and 20% of manually dehulled quinoa meal or flour were evaluated for dough mixing and breadmaking properties and liking of the bread by a small panel. Increasing amounts of quinoa meal or flour increased farinograph absorption and dislike of bread for most of the panel. Dough development time increased with increase in meal but decreased with increase in quinoa flour. At 10% inclusion levels differences in liking from control 100% wheat flour bread were smaller for flour or water extracted meal to most of the panel, than with 10% non-extracted meal. This suggests that 10% inclusion of flour or water extracted meal may have potential for further investigation.     

焦炉装煤烟尘治理的烟气量计算

通过对焦炉装煤烟尘治理的烟气量计算和研究,提出不同治理系统的烟气量计算方法及应采取的措施。     

A general variance predictor for Cavalieri slices

A general variance predictor is presented for a Cavalieri design with slices of an arbitrary thickness t ≥ 0. So far, prediction formulae have been available either for measurement functions with smoothness constant q = 0, 1, … , and t ≥ 0, or for fractional q ∈ [0, 1] with t = 0. Because the possibility of using a fractional q adds flexibility to the variance prediction, we have extended the latter for any q ∈ [0, 1] and t ≥ 0. Empirical checks with previously published human brain data suggest an improved performance of the new prediction formula with respect to the hitherto available ones.     

Prediction of foam growth and its nucleation in free and limited expansion

The influence volume approach (IVA) is often utilized for modeling the mass transfer process dictating bubble growth dynamics in physical foaming. However, the assumed concentration profile in the IVA method is only valid when the changes in dissolved gas concentration are small (less than 5%). In addition, the validity of the IVA method is difficult to justify in chemical foaming applications because of the difficulties involved in defining the dissolved gas concentration profile.In the present work, we define two distinct stages of bubble growth for physical foaming. These two stages are termed as free and limited expansion and are controlled by the bubble nucleation rate. Bubble nucleation is assumed to occur only in the free expansion stage. In this stage, the bubble pressure drops substantially from an initially high pressure in the supersaturated state while the dissolved gas concentration changes very little. The second stage of our two-stage mass transfer model is termed the limited expansion stage and accounts for bubble growth in the late stages of foam evolution, when the pressure changes become small. However, in the limited stage of bubble growth the dissolved gas concentration drops significantly, as the available dissolved gas is depleted. To summarize our two-stage mass transfer model of foam expansion, the pressure difference between the bubble phase and the liquid phase is the primary mechanism for driving mass transfer in the early (free) stages of foam growth and the concentration difference is the driver for bubble growth in the late (limited) stages of growth. The first stage can be regarded as the nucleation stage and it is relatively short; while the second stage can be regarded as the bubble growth stage and is much longer. Most of the bubble volume expansion takes place in the second stage.The concentration gradient at the bubble edge, which is often ignored in other models, is analyzed in detail in this paper. The details of our novel mass transfer model are also presented.     

Preparation and properties of silicone‐containing poly(methyl methacrylate) gels

Poly(methyl methacrylate) (PMMA) gels with varying amounts of silicone and solvent and constant amounts of crosslinker were prepared by solution free radical crosslinking copolymerization of methyl methacrylate (MMA), ethylene glycol dimethacrylate (EGDM), tetraethoxysilane (TEOS) and vinyltriethoxysilane (VTES) comonomer systems. They were then studied in benzene at a total monomer concentration of 3.5 mol L^?1 and 70 °C. The conversion of monomer, volume swelling ratio, weight fraction and gel point were measured as a function of the reaction time, silicone concentration and benzene content up to the onset of macrogelation. Structural characteristics of the gels were examined by using equilibrium swelling in benzene, gel fraction and Fourier‐transform infrared (FTIR) analysis. The morphology of the copolymers was also investigated by SEM. Based on the obtained results, it was concluded that the FTIR data did not have the capacity to show the presence of the VTES or TEOS moiety in these kinds of copolymers. On the other hand, the variation of weight fraction of gel, W_g, and its equilibrium volume swelling ratio in benzene, q_v, exhibited the same behaviour as that of MMA/EGDM copolymers. Also, the dilution of the monomer mixture resulted in an increase in the gel point and swelling degree and a decrease in the percent of conversion and gel fraction. Finally, TEOS is not an ideal silicone compound for reaction in the MMA/EGDM copolymerization system, whereas VTES is a suitable silicone comonomer for this system and it has been proved useful. Copyright © 2005 Society of Chemical Industry     

Erosion rate correlations of a pipe protruded in an abrupt pipe contraction

Erosion is one of the most serious problems in various gas and liquid flow passages such as flow in pipes, pumps, turbines, compressors and many other devices. Sand presence causes loss of pipe wall thickness that can lead to pipe erosion, frequent failures and loss of expensive production time. The importance of this problem is mainly due to many related engineering applications, viz. heat exchangers. In order to reduce the frequency of such pipe erosions, caps in the form of replaceable pipes are protruded in the sudden contraction regions which are exposed to most of the serious erosion rates. In the present work, numerical investigation of the erosion of a pipe protruded in a sudden contraction is presented. The turbulent, steady, 2-D axi-symmetric flow inside an axi-symmetric abrupt contraction pipe with a pipe protrusion embedded in it was solved by steady-state time averaged conservation equations of mass and momentum along with two equation model for turbulence. Particles are tracked using Lagrangian particle tracking. An erosion model was employed to investigate the erosion phenomena for the given geometry. The influence of the different parameters such as the inlet flow velocity (3–10 m/s), the particle diameter (10–400 μm), the protruded pipe geometry (thickness T=1–5 mm and depth H=2–5 mm) and the pipe contraction ratio (Cr=0.25–0.5) on the erosion of pipe protrusion was investigated. Correlations for the influence of inlet flow velocity, depth and thickness of the protruded pipe on the erosion rate are presented.     

砂岩储层渗透率表征方法探讨

渗透率是反映储层渗流能力的重要参数，目前对于单一储层的渗透率表征方法，通常是在岩心分析渗透率或测井解释渗透率的基础上进行厚度加权算术平均。这种方法对于均质的储层来说是适用的，但对于非均质严重的储层，不能准确反映该储层的实际渗流能力。本文提出一种应用可动流体体积权衡表征渗透率的方法，经实际资料验证，能较好地反映储层的实际渗透能力。     

Development of a predictive model for polymer/solvent diffusion coefficient calculations

A new calculation procedure for free‐volume parameters is considered in this work by using viscosity prediction methods and the Levenberg‐Marquardt calculation scheme. All parameters used in the Vrentas–Duda free‐volume theory can be estimated from pure component properties. The prediction results are compared with experimental data for some polymer/solvent systems. The diffusion coefficient calculated by Vrentas–Duda theory can be used in the modeling of membrane separation processes. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008