A high-temperature oxidation-resistant Fe-Mn-Al-Si alloy

To develop satisfactory alloys without Cr or Ni for high-temperature application up to 1100C, three alloys based on Fe-10%Al-Si with differing fourth (or fifth) element additions were oxidized in air at 1100°Cfor 24 hr. A low carbon, Fe-30Mn-10Al-Si alloy exhibited excellent high-temperature oxidation resistance. The total weight gain for 24 hr oxidation in air at 1100°C was only 1.03 mg/cm ². After air oxidation for 6 days at 1100°C, no nodule formation or breakthrough oxidation occurred. Post-oxidation SEM and EDAX examination showed that a thin, compact, protective alumina scale formed on the alloy.Visiting Scientist (People's Republic of China).     

坯料外形对镁合金矩形盒拉深成形的影响

用商业有限元软件模拟了在同一套模具和成形条件下不同毛坯外形的镁合金矩形盒拉深成形过程．依据数值模拟结果，分析了不同坯料外形对镁合金矩形盒拉深成形的影响。结果表明：使用矩形圆角坯料比其他坯料的成形性能好。     

对Al-Cu合金中α-Al及Al2Cu生长行为的探讨

研究了Al-Cu合金中α-Al和Al2Cu的生长行为,分析了初生α-Al及初生Al2Cu作为共晶核心形核的能力.结果发现,在过共晶组织中,初生相Al2Cu形貌大部分有明显的拐角,观察其平面有的呈矩形,呈现小面生长特性.而α-Al与Al2Cu共晶生长时,Al2Cu择优生长特征削弱,与α-Al耦合生长呈现非小面-非小面生长,表明Al2Cu在不同的生长阶段表现出的生长行为不同.在亚共晶组织中,初生相α-Al周围形成离异共晶的Al2Cu,而过共晶组织中初生相Al2Cu周围没有离异共晶的α-Al,表明初生相Al2Cu作为共晶层片核心的能力比初生相α-Al作为共晶层片核心的能力强.     

A novel electroless silver depositing method for magnesium alloys

Depositing silver on magnesium alloy by both electroless plating and organic coatings was studied. The organic coating was made by immersing samples in organosilicon heat-resisting varnish. In this method the organic coating acts as interlayer between the substrate and silver film. When the reaction starts, silver deposits directly on the interlayer. X-ray diffraction and SEM analysis were used to determine the composition and morphology of the interlayer and silver film. The potentiodynamic polarization curves for corrosion studies of coated magnesium alloys were performed in a corrosive environment of 3.5% NaCl（mass fraction） at neutral pH （6.9）. The results indicate that compared with the substrate, the corrosion resistance of coated magnesium alloys increases greatly. Moreover, the method proposed in this work is environmentally friendly, non-toxic chemicals were used. In addition, it provides a new concept for the corrosion inhibition of magnesium alloys.     

医用钴基合金的组织结构及耐腐蚀性能

以锻造CoNiCrMo，CoCrMo和CoCrMoC台会为研究对象，通过金相观察，XRD分析和耐腐蚀试验，研究了3组合金在不同热处理条件下的显微结构，相成分及在Hi同溶液中的耐腐蚀性能。结果表明：2组锻造合金的再结晶温度都是1000℃，且晶粒尺寸随着固溶温度升高和时效时间延长而逐渐变大。3组试样在NaCl溶液中为钴基合金典型的阳极极化曲线；在Hanks’溶液中均有一个二次钝化行为，且锻造CoNiCrMo合金的二次钝化区域较窄，而其他2组合金则较宽；在含柠檬酸三钠的溶液中过钝化电位降低，柠檬酸盐的存在降低了含金的耐腐蚀性能。热处理对合金的耐腐蚀性能影响不大。     

Ag-Cu-In-Sn合金的结构特性

借助金相、X光衍射及SEM方法研究Ag-Cu-In-Sn合金的结构特性及合金各组元在合金相中的分布规律,还讨论了某些相结构对合金力学性能的影响。四元合金的化学成分是(wt％)57～63Ag,17～23Cu,(20—x)In,xSn,其中:Ag+Cu=80wt％,In+Sn=20wt％,2≤x≤16。     

Abnormal Austenite-Ferrite Transformation Behaviors of Fe-ISi: Dilatometric Measurements

WITH THE APPEASING of competition of the totaloutput of iron and steels, the new generation of ultrahigh strength steel, based on the lessen the burden ofenvironment, double improvement of mechanicalproperties and elongation of the serving life, has beenfully outspreaded in the world. More and more researchwork shows that the solid-state microstructureevolution becomes the most effective route in thedevelopment of ultra-high strength steels. A process ofgreat interest in the steel produc…     

含共晶碳化物Fe－Cr－Mn合金在高温含硫气氛中的腐蚀研究

对含碳量为０．５０－２．６３％的Ｆｃ－Ｃｒ－Ｍｎ合金在８００℃下含硫混合气氛中进行腐蚀试验．用Ｘ射线物相分析法分析了腐蚀产物种类及其相对含量，现实测定了元素在腐蚀产物中的分布及试样亚表层共晶碳化物的腐蚀行为。结果表明：试验合金比高Ｎｉ耐热钢具有高的抗腐蚀性；合金的腐蚀行为受硫化及氧化腐蚀双重制约，因而使合金的腐蚀增重呈现峰值，随气氛氧化性增强，峰值向低碳方向移动；共晶碳化物具有比金属基体略好的抗腐蚀性。     

Stress－rupture Property and Microstructure of Yttria Dispersion Strengthened Alloy MA956

Ｓｔｒｅｓｓ－ｒｕｐｔｕｒｅＰｒｏｐｅｒｔｙａｎｄＭｉｃｒｏｓｔｒｕｃｔｕｒｅｏｆＹｔｔｒｉａＤｉｓｐｅｒｓｉｏｎＳｔｒｅｎｇｔｈｅｎｅｄＡｌｌｏｙＭＡ９５６ＳｈａＷｅｉ（沙维）（ＤｅｐａｒｔｍｅｎｔｏｆＣｉｖｉｌＦｎｇｉｎｅｅｒｉｎｇ，ＴｈｅＱｗｅ...     

Development of design principles for a creep-limited alloy for turbine blades

Recent advancements in turbine-blade materials engineering are reviewed in light of general superalloy research and the author’s work on a new powder metallurgy IN-792 creep-limited alloy for application in blades of gas-turbine engines. The developed set of principles presented in this paper incorporates all the factors that must be taken into consideration in selecting and designing an alloy for turbine blades.