医用钴基合金的组织结构及耐腐蚀性能

以锻造CoNiCrMo，CoCrMo和CoCrMoC台会为研究对象，通过金相观察，XRD分析和耐腐蚀试验，研究了3组合金在不同热处理条件下的显微结构，相成分及在Hi同溶液中的耐腐蚀性能。结果表明：2组锻造合金的再结晶温度都是1000℃，且晶粒尺寸随着固溶温度升高和时效时间延长而逐渐变大。3组试样在NaCl溶液中为钴基合金典型的阳极极化曲线；在Hanks’溶液中均有一个二次钝化行为，且锻造CoNiCrMo合金的二次钝化区域较窄，而其他2组合金则较宽；在含柠檬酸三钠的溶液中过钝化电位降低，柠檬酸盐的存在降低了含金的耐腐蚀性能。热处理对合金的耐腐蚀性能影响不大。     

低碳低合金铸钢力学性能的研究

利用Olympus光学显微镜、扫描电镜(SEM)及能谱分析(EDAX)探讨了等温淬火工艺对低碳低合金CrMnSi铸钢力学性能的影响,并通过XRD定量分析了相的组成.结果表明,合适的等温淬火工艺,可获得一定数量的贝氏体和残余奥氏体(约6%)的复合组织,冲击断口形貌由解理刻面变为韧窝状,铸造成形无缺口试样(10 mm×10 mm×55 mm)的冲击韧度由ακ≤30 J/cm2增加至ακ≥170 J/cm2,硬度HRC≥40,具有较高硬度和冲击韧度的配合.     

Abnormal Austenite-Ferrite Transformation Behaviors of Fe-ISi: Dilatometric Measurements

WITH THE APPEASING of competition of the totaloutput of iron and steels, the new generation of ultrahigh strength steel, based on the lessen the burden ofenvironment, double improvement of mechanicalproperties and elongation of the serving life, has beenfully outspreaded in the world. More and more researchwork shows that the solid-state microstructureevolution becomes the most effective route in thedevelopment of ultra-high strength steels. A process ofgreat interest in the steel produc…     

Experimental Study of Microstructure Evolution during Tempering of Quenched Steel and Its Application

LARGE-SIZED FORGINGS are usually intensivelyquenched to obtain the desired microstructuredistribution,high strength and hardness.Becauseresidual stresses are high in quenched large-sizedforgings,tempering processes follow quenchingprocesses to reduce the residual stress and obtain goodmechanical properties.Several differentmicrostructures are generated in quenched steelforgings,such as martensite,bainite and retainedaustenite.Modeling of microstructure evolution inquenched steel during …     

电场固溶对2091A1-Li合金显微结构的影响

用电子探针及透射电镜研究了２０９１ＡｌＬｉ合金的电场固溶对显微结构的影响。结果发现，电场固溶通过促进含铜相溶解提高铜元素的固溶程度，加剧Ｌｉ原子在晶界上的非平衡偏聚，导致析出相δ′分布不均匀，体积分数减少，晶界上出现粗大的δ平衡相，Ｔ１及Ｓ′相均匀弥散分布，合金的力学性能（Ｔ６）达到了应变时效处理（Ｔ８）的水平。     

Effects of γ/γ interfacial structures on continuous coarsening of lamellar microstructure in TiAl alloy during aging

The effects of γ/γ interfacial structures on continuous coarsening of the fully lamellar microstructure in Ti-48Al alloy aged at 1 150 ℃ were investigated by using transmission electron microscopy(TEM). Continuous lamellar coarsening can be achieved not only by migration of interface faults(such as ledges, edges and curved interfaces) but also by migration and decomposition of perfect γ/γ lamellar interfaces. Thermal grooves, initiative positions of interfacial dissociation, can frequently form at the triple point junctions between the 120°-rotational ordered γ domain boundaries within γ lamellae and the lamellar interfaces. During the early stage of aging at 1 150 ℃, the interface migration and dissociation took place preferentially at the 120°-rotational ordered lamellar interfaces. Comparing the relative thermal stability of the true-twin, pseudo-twin and 120°-rotational ordered γ/γ lamellar interfaces shows that the 120°-rotational ordered lamellar interface is the most unstable. The reason of this phenomenon was analyzed through the comparisons of the interfacial energies and atomic arrangements of the three types of γ/γ lamellar interfaces.     

Metallographic sample prepared by ion beam etching

Ion beam etching technique was used to reveal the metallograhpic microstructure and interface morphology of electroplating chromium coating, in particular, whose substrate surface layer was treated in advance by laser quenching. Chemical etchings were also conducted for comparison. The reveal microstructures were observed and analyzed by scanning electron microscopy. The results show that ion beam etching can reveal well the whole microstructures of composite coating-substrate materials.     

Video summarization via minimum sparse reconstruction

The rapid growth of video data demands both effective and efficient video summarization methods so that users are empowered to quickly browse and comprehend a large amount of video content. In this paper, we formulate the video summarization task with a novel minimum sparse reconstruction (MSR) problem. That is, the original video sequence can be best reconstructed with as few selected keyframes as possible. Different from the recently proposed convex relaxation based sparse dictionary selection method, our proposed method utilizes the true sparse constraint L₀ norm, instead of the relaxed constraint _L2,1$L_{2,1}$ norm, such that keyframes are directly selected as a sparse dictionary that can well reconstruct all the video frames. An on-line version is further developed owing to the real-time efficiency of the proposed MSR principle. In addition, a percentage of reconstruction (POR) criterion is proposed to intuitively guide users in obtaining a summary with an appropriate length. Experimental results on two benchmark datasets with various types of videos demonstrate that the proposed methods outperform the state of the art.     

一种变形表面的三维测量方法

提出一种新的利用标定图像进行三维测量的方法。利用SIFT算法找到初始的对应点,然后根据这些点生成三维空间中的种子点,再以这些种子点为中心,向外区域增长,直到完成整个物体表面测量。在每次增长的过程中,需要计算增长的三维空间平面在两个相机上的投影之间的图像相关系数。图像相关系数较大时认为是正确的增长,否则是错误的增长。实验证明,使用该方法能够得到很好的三维测量结果。