交联型聚醚聚氨酯的表征、力学性能及其碱金属盐络合物的导电性能

采用三羟甲基丙烷（ＴＭＰ）作交联剂与聚乙二醇（ＰＥＯ－１５４０）和甲苯二异氰酸酯（ＴＤＩ）反应，得到了具有较好力学性能的交联型聚醚聚氨酯（ＰＥＵ），该聚合物与ＬｉＣｌＯ４的结合物具有较高的室温电导率（σ３０℃＝１．８７×１０￣（－４）Ｓ／ｃｍ）。采用全反射红外光谱（ＡＴＲ－ＩＲ）对聚合物的结构进行了表征。对聚合物的组成、不同ＴＤＩ类型及络合盐浓度对聚合物力学性能及其络合物电导率的影响进行了探讨。低度交联聚合物的络合物，其电导率与温度的关系符合建立在自由体积理论上的ＶＴＦ方程，表明络合物中离子的传导主要是在无定形区域进行，与自由体积有关。     

Rapid analysis of polymer homologues and additives with SFE/SFC-MS coupling

A rapid and easy analysis method for polymers is presented. The method involves sample preparation by SFE, separation of the extracted compounds by SFC and simultaneous quantitative detection by FID, as well as identification of unknowns by MS. The applications illustrate how structural research work and routine polymer analysis can be done with this time saving method.     

Dispersion—flocculation studies on a Goethite-clay system

Dispersion–flocculation studies on a Goethite–clay system using flocculants were carried out as a function of flocculant concentrations, pH of slurry, time of agitation and dispersant dosage. Also, the effects of pH and polymer concentrations on the adsorption behaviour of the system were investigated. Results show that well flocculated goethite was preferentially obtained from 4% goethite/kaolinite clay suspensions, with 50 ppm causticised starch in the slurry at pH values of 3–11·5 and with 50 ppm polyacrylamide at pH values of 3–8. Good flocs were also obtained on flocculation of the goethite suspension with 50 ppm polyacrylamide at pH values of 5–7, while the kaolinite suspension did not respond to the same dosage of causticised starch in the same pH range. Results further reveal that for the goethite/kaolinite suspension, the best results was obtained with 50 ppm polyacrylamide at pH values of 7–10. Based on the data generated in the study, it was concluded that causticised starch is a better flocculant than polyacrylamide for goethite suspensions although polyacrylamide is an excellent flocculant for kaolinite suspensions.     

Phase equilibria of quasi-binary systems consisting of multicomponent polymers 1 and 2. IV: Poly(ethylene oxide)/poly(propylene oxide) systems

To confirm the reliability of the theory of phase equibria of multicomponent polymer 1/multicomponent polymer 2 systems (i.e. quasi-binary systems) and the method of computer experiment based on this theory (Brit. Polym. J., 23 (1990)285; 23 (1990)299; Polym. Int., 29 (1992)219), could point curves (CPC), two-phase volume ratios ( R ) and critical solution points (CSP) have been determined experimentally for the quasi-binary mixtures of poly(ethylene oxide) (M¯_w = 647, M¯_w/M¯_n = 1.15; M¯_w and M¯_n, the weight-average and numberaverage molecular weights, respectively) and poly(propylene oxide) (M¯_w = 2028, M¯_w/M¯_n = 1.08; and M_w = 2987, M_w/M_n = 1.13). The hydroxyl end groups of both polymers were methoxylated in advance by the Cooper & Booth method (Polymer, 18 (1977)164). The thermodynamic interaction parameter between both polymers, χ₁₂, and the concentration dependence parameters for the above quasi-binary systems were determined by the method proposed in a previous paper (Brit. Polym. J., 23 (1990)299). CPC, R and CSP values calculated on the basis of the theory are in good agreement with the values determined experimentally.     

Optical data storage by novel photoelectrochromic polymer

A novel elastic polymer containing 4,4′-bipyridinium salts with tetrakis[3,5-bis(trifluoromethyl)phenyl]borate as part of the main chain was synthesized. The cast film showed persistent and reversible colour changes due to photoinduced electron transfer upon excitation of an ion-pair charge-transfer band (_ex >365 nm) in vacuo. The lifetime of the coloured state markedly depended on temperature. The optically written data were stored without decay below 0°C and were erased thermally at elevated temperatures. The colour changes were reversibly repeatable for many times.     

Surface tailoring of an ethylene propylene diene elastomeric terpolymer via plasma‐polymerized coating of tetramethyldisiloxane

In the research presented here, we explore the use of a low‐energy plasma to deposit thin silicone polymer films using tetramethyldisiloxane (TMDSO) (H(CH₃)₂? Si? O? Si? (CH₃)₂H) on the surface of an ethylene propylene diene elastomeric terpolymer (EPDM) in order to enhance the surface hydrophobicity, lower the surface energy and improve the degradation/wear characteristics. The processing conditions were varied over a wide range of treatment times and discharge powers to control the physical characteristics, thickness, morphology and chemical structure of the plasma polymer films. Scanning electron microscopy (SEM) shows that pore‐free homogeneous plasma polymer thin films of granular microstructure composed of small grains are formed and that the morphology of the granular structure depends on the plasma processing conditions, such as plasma power and time of deposition. The thicknesses of the coatings were determined using SEM, which confirmed that the thicknesses of the deposited plasma‐polymer films could be precisely controlled by the plasma parameters. The kinetics of plasma‐polymer film deposition were also evaluated. Contact angle measurements of different solvent droplets on the coatings were used to calculate the surface energies of the coatings. These coatings appeared to be hydrophobic and had low surface energies. X‐ray photoelectron spectroscopy (XPS) and photoacoustic Fourier‐transform infrared (PA‐FT‐IR) spectroscopy were used to investigate the detailed chemical structures of the deposited films. The optimum plasma processing conditions to achieve the desired thin plasma polymer coatings are discussed in the light of the chemistry that takes place at the interfaces. Copyright © 2004 Society of Chemical Industry     

Cover Picture: Light‐Emitting Organic Solar Cells Based on a 3D Conjugated System with Internal Charge Transfer (Adv. Mater. 22/2006)

The cover image illustrates the dual photovoltaic and electroluminescence function of a single‐layer device based on a thienylenevinylene–triphenylamine with internal charge transfer (ICT), as reported by Cravino, Roncali, and co‐workers on p. 3033. The material forms an organic glass with isotropic electronic properties while ICT leads simultaneously to an extension of the photoresponse to the red and to an increase of the open circuit voltage. The use of an additional layer of C₆₀ further improves the photovoltaic. Images of the sun and moon courtesy NASA/JPL–Caltech.     

Effect of polymerization conditions on o‐phenylenediamine and o‐phenetidine oxidative copolymers

A series of new o‐phenylenediamine (OPD)/o‐phenetidine (PHT) copolymers with partly phenazine‐like structures has been successfully synthesized at three polymerization temperatures by chemically oxidative polymerization in four different polymerization media. The molecular structures and properties of the resulting OPD/PHT polymers were investigated by IR, UV–vis and high‐resolution ¹H NMR spectroscopies, and DSC, in order to ascertain the effect of reaction temperature, comonomer ratio and acid medium. The copolymerization mechanism of OPD with PHT monomers has been proposed. It is found that the statistical OPD/PHT copolymer obtained at a temperature of 118 °C has a higher degree of polymerization than that obtained at 12–17 °C. The OPD content in the copolymers calculated from NMR spectroscopic analysis is higher than that in the feed OPD content, whereas the OPD content calculated from element analysis is slightly lower than the feed OPD content. It can be predicted that denitrogenation takes place in the OPD units during the polymerization process at OPD/PHT molar ratios of 90/10 and 100/0. These OPD/PHT copolymers exhibit a much better solubility than the OPD homopolymer, hence suggesting an incorporation of PHT units into the phenazine structure of the homopolymer. The thermal behavior of the copolymers was also studied. Copyright © 2004 Society of Chemical Industry     

Morphology development in polyethylene/polystyrene blends: the influence of processing conditions and interfacial modification

The influence of processing conditions and interfacial modification on the morphology evolution and the composition range within which fully co‐continuous high density polyethylene/polystyrene blend structures can exist during blending in a single screw extruder was studied. Blends ranging from pure A to pure B component, with and without compatibilizer, were prepared under two different shear rates. It was found that high shear rates displaced the breakdown–coalescence balance of the dispersed nodules to the side of coalescence, narrowing the percolation domain and the critical composition for full co‐continuity decreased with increasing shear rates. The addition of a tri‐block compatibilizer induced the percolation threshold of the polystyrene phase to begin at lower percentages of polyethylene but the phase inversion point did not change. The experimental results are discussed in the light of various theoretical models. Copyright © 2005 Society of Chemical Industry     

Thermodynamic state of reinforced interpenetrating polymer networks

The free energies of mixing of two networks in the interpenetrating polymer network based on crosslinked polyurethane and poly(ester acrylate) have been determined by the vapour sorption method. It was established that the constituent networks in the IPN are not miscible. The introduction of fillers of different chemical nature increases the compatibility. The thermodynamic affinity of the fillers to the individual networks and IPN was estimated. It was established that when the free energy of interaction of one or both components of the IPN with the filler is negative, reinforcement leads to the formation of a compatible and equilibrium system. For fillers having no affinity to the polymers, compatibilization is observed, which is connected with slowing down of phase separation in the system in the presence of filler.