换热器表面预处理及防腐工艺

石化换热器许多设备都由碳钢制作,需要涂镀渗防腐,为保证防腐层质量,需要进行严格的表面预处理。概述了机械与化学表面预处理及相关的防腐工艺。     

纺牵—步法中粗旦丙纶长丝沸水收缩率初探

在纺牵联合一步法纺丝机上研究了丙纶切片的熔融指数对纤维沸水收缩率的影响，发现熔融指数高的切片，其纤维的沸水收缩率变化大。沸水收缩率随热定型的温度升高而下降。沸水收缩率可根据用户提供中心值（Ｍ）通过实验确定，一般以Ｍ±１．５为宜。     

主要化工设备的技术进展

本文分析了70年代以来国际化工设备朝单系列大型化及高压力的发展趋势,以及高效能、低能耗的要求,在这个基础上介绍当前国内外化工设备新设备研制及旧设备改造的进展情况。最后提出对广州市、广东省在“八·五”期间化工设备技术的展望:乙烯设备国产化与旧设备的更新换代,进行技术改造。     

一步法生产涤纶FDY工艺的探讨

利用ＫＶ７３１纺丝设备一步法生产出涤纶ＦＤＹ，探讨了热辊拉伸和熔体温度对纤维质量的影响。采用高特性粘数的聚酯切片，严格控制纺丝工艺，可以在５０００ｍ／ｍｉｎ的纺丝速度下纺制高质量的细旦涤纶ＦＤＹ。     

电除尘器出口烟气废热的利用

介绍了采用热管锅炉回收硫酸系统电除尘器出口烟气废热情况，可回收废热生产0．8MPa饱和蒸汽1．0t/h。通过严格控制饱和蒸汽压力、炉气的三氧化硫含量及入炉原料的水分含量，热管锅炉连续运行两年未发生泄漏。运行一年即可收回成本，经济效益显著。     

对甲醇精馏几个问题的认识

简述甲醇精馏三塔流程原理 ,分析了加压精馏塔及常压精馏塔物料和热量平衡关系 ,提出了操作中应注意的事项     

气化炉复合炉衬的传热计算

新型 (多喷嘴对置 )水煤浆气化炉拟采用水冷管和耐火浇铸料组成的复合炉衬结构 .炉内的高温高压对复合炉衬的高温侵蚀十分严重 ,是影响其寿命的重要因素 ,因此合理设计气化炉复合炉衬的结构对充分发挥其材质的作用具有十分重要的意义 .建立了气化炉复合炉衬的传热计算的数学模型 ,同时编制了模型求解的计算程序 ,并用某工艺条件对复合炉衬的温度分布进行了计算 .结果表明 ,该方法可有效计算出复合炉衬的温度分布情况 ,为复合炉衬的设计、运行和维护提供理论依据     

A rapid test to measure performance,emission and wear of a diesel engine fueled with palm oil diesel

Results of performance, emission and tribological evaluations of palm oil methyl ester and its blends with conventional diesel in an automobile diesel engine test bed are presented. Polymerization and carbon deposits on the fuel injector were monitored. CO, CO₂, O₂, combustion efficiency and temperature of exhaust gases were also measured. Palm oil methyl ester and its blends have great potential as alternative diesel fuel. Performance and exhaust gas emission for palm oil methyl ester and its blends with conventional diesel are comparable with those of conventional diesel fuel. Palm oil methyl ester does not pose a severe environmental problem and will not deteriorate engine and bearing components.     

应用WCA微扰理论推算非极性液体比热容的新方法

本文首次将统计热力学的Ｗｅｅｋｓ－Ｃｈａｎｄｌｅｒ－Ａｎｄｅｒｓｏｎ（简称ＷＣＡ）微扰理论应用于非极性液体定容比热容和定压比热容的推算，用一些液体的ｐ－ｖ－Ｔ实验数据拟合了理论中所用ＬＪ势能函数的势能参数，并提出一个通用关联式。本文方法具有通用性，在编制的计算程序中只需输入物质的临界温度、临界比容、偏心因子等就能算出相应的比热容，工程应用十分方便。     

Effect of Twin-Plane Reentrant Edge on the Coarsening Behavior of Barium Titanate Grains

When BaTiO₃ ceramics were sintered at relatively low temperatures (≤1250°C), the grains with reentrant edges caused by a (111) double twin grew exclusively. As a result, a microstructure with a bimodal grain-size distribution composed of platelike large grains and fine matrix grains was obtained. In contrast, at the usual sintering temperature between 1250° and 1350°C, grains containing a (111) double twin did not exhibit any growth advantage. In this case, a coarse and uniform microstructure was obtained. When this coarse-grained specimen was further heat-treated at 1365°C, the grains possessing a double twin were observed to grow exclusively again. The results were explained in terms of a coarsening process controlled by two-dimensional nucleation.