Performance modeling and evaluation of data/voice services in wireless networks

Application-level performance is a key to the adoption and success of the CDMA 2000. To predict this performance in advance, a detailed end-to-end simulation model of a CDMA network is built to include application traffic characteristics, network architecture, network element details using the proposed simulation methodology. We assess the user-perceived application performance when a RAN and a CN adopt different transport architectures such as ATM and IP. To evaluate the user-perceived quality of voice service, we compare the end-to-end packet delay for different vocoder schemes such as G.711, G.726 (PCM), G.726 (ADPCM), and vocoder bypass scheme. By the simulation results, the vocoder bypass scenario shows 30% performance improvement over the others. We also compare the quality of voice service with and without DPS scheduling scheme. We know that DPS scheme keep the voice delay bound even if the service traffic is high. For data packet performance, HTTP v.1.1 shows better performance than that of HTTP v.1.0 due to the pipelining and TCP persistent connection. We may conclude that IP transport technology is better solution for higher FER environment since the packet overhead of IP is smaller than that of ATM for web browsing data traffic, while it shows opposite effect to the small size voice packet in RAN architecture. We show that the 3G-1X EV-DO system gives much better packet delay performance than 3G-1X RTT. The main conclusion is that end-to-end application-level performance is affected by various elements and layers of the network and thus it must be considered in all phases of the development process. Jae-Hyun Kim He received the B.S., M.S., and Ph.D. degrees, all in computer science and engineering, from Hanyang University, Ansan, Korea, in 1991, 1993, and 1996 respectively. In 1996, he was with the Communication Research Laboratory, Tokyo, Japan, as a Visiting Scholar. From April 1997 to October 1998, he was a post-doctoral fellow at the department of electrical engineering, University of California, Los Angeles. From November 1998 to February 2003, he worked as a member of technical staff in Performance Modeling and QoS management department, Bell laboratories, Lucent Technologies, Holmdel, NJ. He has been with the department of electrical engineering, Ajou University, Suwon, Korea, as an assistant professor since 2003. His research interests include QoS issues and cross layer optimization for high-speed wireless communication. Dr. Kim was the recipient of the LGIC Thesis Prize and Samsung Human-Tech Thesis Prize in 1993 and 1997, respectively. He is a member of the Korean Institute of Communication Sciences (KICS), Korea Institute of Telematics and Electronis (KITE), Korea Information Science Society (KISS), and IEEE. Hyun-Jin Lee received the B.S. degree in electrical engineering from Ajou University, Suwon, Korea, in 2004, and is working toward the M.S. degree and Ph. D. degree in electrical engineering at Ajou University. He has been awarded Samsung Human-Tech Thesis Prize in 2004. His research interests QoS, especially network optimization and wireless packet scheduling. He is a member of the KICS. Sung-Min Oh received the B.S. and M. S. degrees in electrical engineering form Ajou University, Suwon, Korea, in 2004, and is working toward the Ph. D. degree in electrical engineering at Ajou University. His research interests QoS performance analysis and 4G network. He is a member of the KICS. Sung-Hyun Cho received his B.S., M.S., and Ph.D. in computer science and engineering from Hanyang University, Korea, in 1995, 1997, and 2001, respectively. From 2001 to 2005, he has been with Samsung Advanced Institute of Technology, where he has been engaged in the design and standardization of MAC and upper layers of B3G, IEEE 802.16e, and WiBro systems. He is currently a MAC part leader in the telecommunication R&D center of Samsung Electronics. His research interests include 4G air interface design, radio resource management, cross layer design, and handoff in wireless systems.     

均匀设计法分析制备过程对钴钼硫化物催化剂机械强度的影响

建立了CoMoP/Al2O3加氢精制催化剂机械强度及其可靠性在制备过程中的数学模型,采用均匀设计考察了浸渍、干燥、煅烧、硫化4个制备过程中,浸渍时间、干燥温度、干燥时间、煅烧温度、煅烧时间、硫化温度和硫化升温速率7个实验因子对催化剂强度均值、Weibull模量的影响,同时考察了这些因素对颗粒密度的影响。方差分析表明所有模型都是充足的。实验结果表明,硫化过程是影响催化剂强度均值的主要过程。在实验范围内提高硫化温度、降低硫化时的升温速率有利于提高催化剂的强度。影响催化剂Weibull模量的因素主要为各个制备过程的交互效应。要提高催化剂强度的可靠性就必须全面考虑催化剂制备的各个过程,特别是各个制备过程的交互效应。     

Innovation in construction: a sociology of technology approach

An alternative approach to understanding innovation is made using two intersecting ideas. The first is that successful innovation requires consideration of the social and organizational contexts in which it is located. The complex context of construction work is characterized by inter-organizational collaboration, a project-based approach and power distributed amongst collaborating organizations. The second is that innovations can be divided into two modes: 'bounded', where the implications of innovation are restricted within a single, coherent sphere of influence, and 'unbounded', where the effects of implementation spill over beyond this. Bounded innovations are adequately explained within the construction literature. However, less discussed are unbounded innovations, where many firms' collaboration is required for successful implementation, even though many innovations can be considered unbounded within construction's inter-organizational context. It is argued that unbounded innovations require an approach to understand and facilitate the interactions both within a range of actors and between the actors and technological artefacts. The insights from a sociology of technology approach can be applied to the multiplicity of negotiations and alignments that constitute the implementation of unbounded innovation. The utility of concepts from the sociology of technology, including 'system building' and 'heterogeneous engineering', is demonstrated by applying them to an empirical study of an unbounded innovation on a major construction project (the new terminal at Heathrow Airport, London, UK). This study suggests that 'system building' contains outcomes that are not only transformations of practices, processes and systems, but also the potential transformation of technologies themselves.     

3-D MCM封装技术及其应用

介绍了超大规模集成电路（VLSI）用的3-D MCM封装技术的最新发展，重点介绍了3-D MCM封装垂直互连工艺，分析了3-D MCM封装技术的硅效率、复杂程度、热处理、互连密度、系统功率与速度等问题，并对3-D MCM封装的应用作了简要说明。     

Thermal stability of reinforced Nb3Sn composite superconductor under cryocooled conditions

Several types of reinforced Nb₃Sn wires have been developed to prevent reduction of superconducting properties by applying a strong electromagnetic force. To fabricate a cryocooled magnet using those reinforced wires, we experimentally measured the minimum quench energy (MQE) under cryocooled conditions of some reinforced Nb₃Sn wires. As a result, it became clear that thermal stability expressed as MQE was controlled by the temperature margin between the temperature of the operating condition and the transition temperature from superconductivity to normal. Using the FEM analysis, it was realized that the cause of the decline in thermal stability for the reinforced wires was the low thermal conductivity of the reinforced materials.     

盐井水平对接钻井技术

钻一口通过主采盐层的水平井与已完成的直井对接，形成连通井(形如“U”字)，一口井注水溶解盐／芒硝矿，另一口井采出卤水，这是盐化工业对钻井提出的要求。针对水平对接盐井井身轨迹设计、着陆段、水平段的轨迹控制和连通技术，介绍了水平段侧钻时的钻井液技术。     

Effect of Y2O3, CeO2 on Sintering Properties of Si3N4 Ceramics

The effect of rare earth oxides Y203 or Ce02 on sintering properties of Si3N4 ceramics was studied and the mechanism of assisting action during sintering was analyzed. The results in dicate that the best sintering properties appear in Si3N4 ceramics with 5% Y203 or 8% CeO2. Secondary crystallites are formed at grain boundaries after heat treatment,which decreases the amount of glass phase and contributes to the improvement of high-temperature mechanical properties of silicon nitride.     

1/3码的动态CMOS全自检电路的设计

自检测电路设计方法有多种多样,本文中介绍了TSC电路的概念,并采用1/3码的动态CMOS设计TSC电路,通过在Cadence环境下仿真,仿真结果表明本设计可行。     

烧成及热处理工艺对钛酸锶铅基热敏材料性能及显微结构的影响

研究了烧成及热处理工艺对钛酸锶铅基热敏材料的阻温特性及显微结构的影响。通过扫描电镜（ＳＥＭ）和能量分散仪（ＥＤＡＸ）分析了材料的显微结构及不同形貌晶粒的成份。通过对组成、烧成及热处理工艺的控制，可得到具有Ｖ型ＰＴＣＲ特性的热敏材料。