Influence of the surface conditions on permeation in the deuterium–MANET system

The condition of the surfaces is of crucial importance for the deuterium permeation through materials. In this work a study of the surface constants for the adsorption (σk₁) and release (σk₂) of deuterium under different surface conditions on the martensitic steel DIN 1.4914 (MANET) has been carried out. The growth of an oxide surface layer (Cr₂O₃) of about 25–30 nm in a MANET sample, heat treated in an oxidizing environment, compared to the bare MANET that have a ‘natural' oxide of about 5 nm has provoked a reduction of both the permeation rate and the recombination coefficient (about 3 orders of magnitude). In addition, the permeation governing process has changed from diffusion-limited to surface-limited. The measurements of the permeation rate of deuterium were performed by a gas-phase permeation technique over the temperature range 574–746 K and for deuterium driving pressures in the range from 3 to 10⁵ Pa.     

紧凑 Tokamak(球形环)聚变堆第一壁及中心导体柱上中子负荷及核热计算与分析

采用通用蒙特卡罗粒子输运程序ＭＣＮＰ／３８计算低环径比Ｔｏｋａｍａｋ（紧凑环或球形环）聚变堆第一壁及中心导体上的中子壁负荷分布和核热沉积分布，并与常规Ｔｏｋａｍａｋ堆第一壁上中子壁负荷分布和核热沉积分布进行比较、分析。结果表明，在中子壁负荷归一化为１ＭＷ／ｍ２时，与常规Ｔｏｋａｍａｋ相比，在低环径比Ｔｏｋａｍａｋ堆第一壁及中心柱表面上中子壁负荷分布峰值并不比常规Ｔｏｋａｍａｋ堆第一壁上的峰值高，而且低于低环径比Ｔｏｋａｍａｋ堆整个第一壁上的平均值，而中心柱上的核热沉积峰值稍高于常规Ｔｏｋａｍａｋ堆第一壁上的核热沉积峰值，但对较高中子壁负荷情况，中心导体柱上的核热沉积和辐照损伤仍可能是比较严重和值得特别研究的问题。     

Heat loss and thermoelectric generator design

With the object of evaluating its importance to thermoelectric generator design, heat loss is introduced into the standard thermoelectric generator design theory. The theory for both the constant hot and cold junction temperatures model and the constant heat input model are so modified. The modification is first order and, therefore, is limited to small leg heat-transfer coefficients. Numerical results using representative properties show that significant differences can exist between the optimum geometry and performance of a generator idealized as lossless and those of a generator designed by the modified theory. The largest differences occur with the constant heat input model.     

Simultaneous mass and heat transfer under mixed convection along a vertical cone

Steady laminar binary mixed convection flow along a vertical circular cone under the combined buoyancy effects of thermal and species diffusion is studied analytically. The analysis is confined to mass diffusion processes with low concentration levels. In the analysis the surface of the cone is assumed to be at a uniform temperature and uniform concentration. Numerical results for the local Sherwood number, local Nusselt number and local friction factor are presented. Representative temperature, concentration and velocity profiles are also shown. The analysis covers the diffusion of common gases and vapours into air. Considerations are given to the situations where the buoyancy forces assist and oppose the forced convection flow for various possible combinations of the thermal and species diffusion processes.     

低电压氧化锌压敏电阻器的研究

研究了一种制造低电电压氧化锌压敏电阻器的方法。在基本成分的基础上适当加入二氧化钛可降低梯度电压（Ｖ１ｍＡ／ｍｍ），适量掺硼和改进热处理工艺可减小元件的漏电流和提高其稳定性。     

从第八次全国热处理大会看我国热处理技术发展的热点

对第八次全国热处理大会的大会报告和交流论文进行了概述和分析，并就有关我国热处理技术发展的热点问题提出了笔者的一些见解。     

Strengthening technology and mechanism for semi-solid die casting of aluminum alloy

Combined with theoretical evaluation,an optimized strengthening process for the semi-solid die castings of A356 aluminum alloy was obtained by studying the mechanical properties of castings solution treated and aged under different conditions in detail,then,the semi-solid die castings and liquid die castings were heat treated with the optimized process.The results show that the mechanical properties of semi-solid die castings of aluminum alloy are superior to those of the liquid die castings,especially the strengthening degree of heat treated semi-solid die castingsis much greater than that of liquid die castings with the tensile strength more than 330 MPa and the elongation more than 10％,and this is mainly contributed to the non-dendritic and more compact microstructure of semi-solid die castings.The strengthening mechanism of heat treatment for the semi-solid die castings of A356 aluminum alloy is due to the dispersive precipitation of the second phase(Mg2 Si) and formation of GP Zone.     

换热器表面预处理及防腐工艺

石化换热器许多设备都由碳钢制作,需要涂镀渗防腐,为保证防腐层质量,需要进行严格的表面预处理。概述了机械与化学表面预处理及相关的防腐工艺。     

Calculated effect of pulsed pheromone release on range of attraction

In order to assess the possible function of pulsed release of windborne pheromones, calculations were performed to predict the concentration pattern downwind of the source. Two patterns of pulsed releases (sinusoidal and instantaneous) were compared to a constant release pattern. In all three cases, the average rate of release was the same. Assuming the receiving animal needs only a momentary exposure to concentrations above threshold to respond, it is clear that sinusoidal release has a greater distance of detection than constant release and that instantaneous release is even better. The relative magnitude of the increase in range of detection depends on the ratio of average release rate to threshold concentration. Pulsed releases have a greater advantage when the threshold is high and the range of attraction is inherently short. Under these conditions, sinusoidal release can double the range of attraction and instantaneous release can increase it 10-fold. In contrast, with a low threshold and consequent long range of attraction, the pulsed patterns are lost and the increase in range is insignificant. Several testable predictions are derived from the hypothesis that the primary function of pulsed release is to extend the range and time over which a given quantity of pheromone can act.