Development of sealing compositions with nanostructure iron-based fillers

The possibility of utilizing nanopowders of iron and Fe-Co-Ni produced bu a thermochemical method in the fabrication of sealing composition materials is investigated. It is established that such hermetic sealing composition materials function reliably under extremal conditions and guarantee elevated strength of adhesion to the surface of the metal and high corrosion and temperature stability. __________ Translated from Poroshkaya Metallurgiya, Nos. 3–4(448), pp. 112–117, March–April, 2006.     

Rapid analysis of polymer homologues and additives with SFE/SFC-MS coupling

A rapid and easy analysis method for polymers is presented. The method involves sample preparation by SFE, separation of the extracted compounds by SFC and simultaneous quantitative detection by FID, as well as identification of unknowns by MS. The applications illustrate how structural research work and routine polymer analysis can be done with this time saving method.     

Effects of temperature, ammonium and glucose concentrations on yeast growth in a model wine system

In enology, alcoholic fermentation is a complex process involving several mechanisms. Slow and incomplete alcoholic fermentation is a chronic problem for the wine industry and factors leading to sluggish and stuck fermentations have been extensively studied and reviewed. The most studied cause of sluggish and stuck fermentation is the nitrogen content limitation. Nevertheless, other factors, such as temperature of fermentation and sugar concentration can affect the growth of yeasts. In this study we modelled the yeast growth‐cycle in wine model system as a function of temperature, sugar and ammonium concentrations; the individual effects and the interaction of these factors were analysed by means of a quadratic response surface methodology. Cell concentrations and weight loss were monitored in the whole wine fermentation process. The results of central composite design show that lower is the availability of nitrogen, higher is the cell growth rate; moreover, initial nitrogen concentration also influences survival time of Saccharomyces cerevisiae.     

Ermüdungsverhalten und Dauerfestigkeit von Graphit und Aluminium – infiltriertem Graphit

Fatigue behaviour and endurance limit of graphite and of aluminium‐infiltrated graphite Fatigue properties of polycrystalline, isotropic graphite FU2590 and of FU2590 infiltrated with AlSi7Mg (FU2590/AlSi7Mg) were investigated in reversed bending tests at 25 Hz at numbers of cycles below 10⁷ and in tension‐compression tests at 20 kHz below 10⁹ cycles. The open porosity of Graphite (10‐11 Vol.‐%) was infiltrated with the aluminium alloy using the squeeze casting infiltration method, which led to an increase of the bending strength by 50 %, increase of tensile strength by 30 % and increase of stiffness by 15 %. Fully reversed tension‐compression loading of FU2590 delivers a mean endurance limit at 10⁹ cycles at the normalized maximum stresses (i.e. maximum tension stress of a cycle divided by the static strength) of 0,65±0,03. Mean numbers of cycles to failure of 10⁴ were found in fully reversed bending tests at the normalized maximum stress of 0,78. The infiltrated material shows approximately 30 % higher cyclic strength in reversed bending tests, and the mean endurance limit under tension compression loading increases by 15 %. The increased endurance limit of the infiltrated material is caused by the increased stiffness. The increased toughness of graphite due to the infiltration with aluminium is of additional beneficial influence at the higher cyclic stresses investigated in reversed bending tests and in static tests.     

Neutron Stress Measurement of W‐Fiber Reinforced Cu Composite

Stress measurement methods using neutron and X‐ray diffraction were examined by comparing the surface stresses with internal stresses in the continuous tungsten‐fiber reinforced copper‐matrix composite. Surface stresses were measured by X‐ray stress measurement with the sin²ψ method. Furthermore, the sin²ψ method and the most common triaxal measurement method using Hooke's equation were employed for internal stress measurement by neutron diffraction. On the other hand, microstress distributions developed by the difference in the thermal expansion coefficients between these two phases were calculated by FEM. The weighted average strains and stresses were compared with the experimental results. The FEM results agreed with the experimental results qualitatively and confirmed the importance of the triaxial stress analysis in the neutron stress measurement.     

Dispersion—flocculation studies on a Goethite-clay system

Dispersion–flocculation studies on a Goethite–clay system using flocculants were carried out as a function of flocculant concentrations, pH of slurry, time of agitation and dispersant dosage. Also, the effects of pH and polymer concentrations on the adsorption behaviour of the system were investigated. Results show that well flocculated goethite was preferentially obtained from 4% goethite/kaolinite clay suspensions, with 50 ppm causticised starch in the slurry at pH values of 3–11·5 and with 50 ppm polyacrylamide at pH values of 3–8. Good flocs were also obtained on flocculation of the goethite suspension with 50 ppm polyacrylamide at pH values of 5–7, while the kaolinite suspension did not respond to the same dosage of causticised starch in the same pH range. Results further reveal that for the goethite/kaolinite suspension, the best results was obtained with 50 ppm polyacrylamide at pH values of 7–10. Based on the data generated in the study, it was concluded that causticised starch is a better flocculant than polyacrylamide for goethite suspensions although polyacrylamide is an excellent flocculant for kaolinite suspensions.     

Phase equilibria of quasi-binary systems consisting of multicomponent polymers 1 and 2. IV: Poly(ethylene oxide)/poly(propylene oxide) systems

To confirm the reliability of the theory of phase equibria of multicomponent polymer 1/multicomponent polymer 2 systems (i.e. quasi-binary systems) and the method of computer experiment based on this theory (Brit. Polym. J., 23 (1990)285; 23 (1990)299; Polym. Int., 29 (1992)219), could point curves (CPC), two-phase volume ratios ( R ) and critical solution points (CSP) have been determined experimentally for the quasi-binary mixtures of poly(ethylene oxide) (M¯_w = 647, M¯_w/M¯_n = 1.15; M¯_w and M¯_n, the weight-average and numberaverage molecular weights, respectively) and poly(propylene oxide) (M¯_w = 2028, M¯_w/M¯_n = 1.08; and M_w = 2987, M_w/M_n = 1.13). The hydroxyl end groups of both polymers were methoxylated in advance by the Cooper & Booth method (Polymer, 18 (1977)164). The thermodynamic interaction parameter between both polymers, χ₁₂, and the concentration dependence parameters for the above quasi-binary systems were determined by the method proposed in a previous paper (Brit. Polym. J., 23 (1990)299). CPC, R and CSP values calculated on the basis of the theory are in good agreement with the values determined experimentally.     

Optical data storage by novel photoelectrochromic polymer

A novel elastic polymer containing 4,4′-bipyridinium salts with tetrakis[3,5-bis(trifluoromethyl)phenyl]borate as part of the main chain was synthesized. The cast film showed persistent and reversible colour changes due to photoinduced electron transfer upon excitation of an ion-pair charge-transfer band (_ex >365 nm) in vacuo. The lifetime of the coloured state markedly depended on temperature. The optically written data were stored without decay below 0°C and were erased thermally at elevated temperatures. The colour changes were reversibly repeatable for many times.     

Surface tailoring of an ethylene propylene diene elastomeric terpolymer via plasma‐polymerized coating of tetramethyldisiloxane

In the research presented here, we explore the use of a low‐energy plasma to deposit thin silicone polymer films using tetramethyldisiloxane (TMDSO) (H(CH₃)₂? Si? O? Si? (CH₃)₂H) on the surface of an ethylene propylene diene elastomeric terpolymer (EPDM) in order to enhance the surface hydrophobicity, lower the surface energy and improve the degradation/wear characteristics. The processing conditions were varied over a wide range of treatment times and discharge powers to control the physical characteristics, thickness, morphology and chemical structure of the plasma polymer films. Scanning electron microscopy (SEM) shows that pore‐free homogeneous plasma polymer thin films of granular microstructure composed of small grains are formed and that the morphology of the granular structure depends on the plasma processing conditions, such as plasma power and time of deposition. The thicknesses of the coatings were determined using SEM, which confirmed that the thicknesses of the deposited plasma‐polymer films could be precisely controlled by the plasma parameters. The kinetics of plasma‐polymer film deposition were also evaluated. Contact angle measurements of different solvent droplets on the coatings were used to calculate the surface energies of the coatings. These coatings appeared to be hydrophobic and had low surface energies. X‐ray photoelectron spectroscopy (XPS) and photoacoustic Fourier‐transform infrared (PA‐FT‐IR) spectroscopy were used to investigate the detailed chemical structures of the deposited films. The optimum plasma processing conditions to achieve the desired thin plasma polymer coatings are discussed in the light of the chemistry that takes place at the interfaces. Copyright © 2004 Society of Chemical Industry     

Development of cable fault location method using fiber optic distributed temperature sensor

When ground-fault problems occur on a cable line, immediate fault location and restoration are required. Therefore, various new methods to locate the fault point instantaneously have been investigated to replace such conventional methods as the Murray loop method and the pulse radar method [1]. These methods require a long time to locate the fault point. One possible fault location method is to sense the temperature rise following a ground fault using a fiber optic distributed temperature sensor. Application of this method was found feasible through sensing the temperature rise at a ground-fault test using a thermocouple as a temperature sensor with test cables [4]. A power/optical composite cable was prepared experimentally and after verifying its thermal mechanical performance, the temperature rise at an incidence of a fault was determined and the anticipated performance was demonstrated in a ground-fault test. This article describes the outline of the test.