The As-prepared surfaces of C-axis-oriented Nd1Ba2Cu3Oy thin films characterized using scanning probe microscopes

Recently, superconducting Nd₁Ba₂Cu₃O_y (Ndl23) thin films with high superconducting transition temperature (T _c) have been successfully fabricated at our institute employing the standard laser ablation method. In this paper, we report the results of surface characterization of the Nd123 thin films using an ultrahigh vacuum scanning tunneling microscope/spectroscopy (UHV-STM/STS) and an atomic force microscope (AFM) system operated in air. Clear spiral pattern is observed on the surfaces of Nd123 thin films by STM and AFM, suggesting that films are formed by two-dimensional island growth mode. Contour plots of the spirals show that the step heights of the spirals are not always the integer or half-integer number of thec-axis parameter of the structure. This implies that the surface natural termination layer of the films may not be unique. This result is supported byI-V STS measurements. The surface morphology of the Nd123 thin films is compared with that of thec-axis-oriented Y₁Ba₂Cu₃S_y thin films. Surface atomic images of the as-prepared Nd123 thin films are obtained employing both STM and AFM. STS measurements show that most of the surfaces are semiconductive. The results of STS measurements together with the fact that we are able to see the surface atomic images using scanning probe microscopes suggest that exposure to air does not cause serious degradation to the as-prepared surfaces of Nd123 thin films.     

Subdivision of work on construction projects

In order to control a project, construction management requires project information. This is obtained through accounting, estimating, cost management and scheduling functions which produce project reports. These reports are best obtained by subdividing the project into small parts. The ways in which each of these functions subdivides a project in order to produce its reports is discussed, together with a means of interrelating this information with a technique known as the work breakdown structure.     

人支气管上皮靶细胞形态学参数的测量

支气管上皮靶细胞形态学参数对计算受氡子体照射的支气管的剂量是很重要的。本文介绍利用奥尔新兰-PAS 染色的外科切除人肺组织切片,测量基底细胞粘液细胞和的胞核深度与数目。结果表明,叶、段和小支气管的粘液细胞核深度分别为相应节段基底细胞的61%、69%和73%;此三节段粘液细胞的数目分别为基底细胞的53%、29%和28%,平均为37%。     

氧化铝厂渣浆泵机械密封的失效形式及改进措施

本文介绍了渣浆泵机械密封的失效形式,并根据长期现场工作经验,分析了机械密封泄漏的主要原因,据此提出了改进措施,通过对动静环密封面倒角,改变密封面尺寸及载荷系数后有效地解决了由于径向跳动过大而引起的密封面刮碰擦裂的失效问题。     

线缆护套材料在我国西部环境中的试验研究

本文通过对线缆外护套材料在我国西部地区严酷环境试验站中土壤和大气1～5年的试验结果分析，总结了塑料护套材料的耐蚀性能。为线缆护套的防护设计、合理选材及制定标准提供科学依据。     

棕刚玉粉中Al2O3含量分析方法的探讨

对耐火材料——棕刚玉粉的质量分析控制，提出了用实用性的检测方法测定其Al2O3含量。通过与国家标准分析方法的对比试验，证实快速实用分析方法测定棕刚玉粉中Al2O3含量是可行的。