Identification of gaps in mangrove forests with airborne LIDAR

Mangrove forests change frequently due to disturbances from tropical storms, frost, lightning, and insects. It has been suggested that the death and regeneration of trees in small gaps due to lightning may play a critical role in mangrove forest turnover; however, the large-scale quantification of spatial pattern and areas of gaps is lacking for investigating this issue. Airborne light detection and ranging (LIDAR) technology provides an effective way for identifying gaps by remotely obtaining direct measurements of ground and canopy elevations. A method based on an alternative sequential filter and black top-hat mathematical morphological transformation was developed to extract gap features. Comparison of identified gap polygons with raw LIDAR measurements and field surveys shows that the proposed method successfully extracted gap features in mangrove forests in Everglades National Park. There are 400–500 lightning gaps per square kilometer in mangrove forests at the study sites. The distribution of gap sizes follows an exponential form and the area of gaps with sizes larger than 100 m² account for 55–61% of the total area of gaps. The area of gaps in the mangrove forest in Everglades National Park is about 4–5% of the total forest area and the average gap formation rate is about 0.3% of the total forest area per year, indicating that lightning gaps play an important role in mangrove forest dynamics.     

A novel open-loop high-speed CMOS sample-and-hold

A new open-loop high-speed CMOS sample-and-hold is presented. Based on new method for further reduction of voltage-dependent charge injection, a new CMOS sample-and-hold was designed. Simulation results confirm the effectiveness of this method. Over 10 dB improvement in signal-to-noise ratio, compared to the signal-to-noise ratio of conventional bottom plate sampling S/Hs was achieved with this method. A comparison between newly designed S/H and the bottom-plate sampling S/H is presented.     

Nucleation of copper on an assembly of carbon microelectrodes

The initial stage of copper electrodeposition on the electrochemically activated assembly of carbon microelectrodes from an acid solution of copper sulfate was investigated using cyclic voltammetry, potentiostatic pulse technique and electrochemical impedance spectroscopy. Analysis of the experimental current transients has been carried out using a non-linear fitting procedure according to the model that takes into account spherical diffusion towards a disc-shaped microelectrode. The higher values of diffusion coefficient in comparison with those observed on planar electrodes were explained with an increased diffusion caused by the electrode geometry. Impedance spectra showed two time constants, the high-frequency related to the charge transfer process and the low-frequency corresponded to the deposit morphology.     

锌基合金模具的应用及探讨

本文分析了锌基合金模具制造及使用过程中容易出现热裂、翘曲、收缩的问题，并提出了解决这些问题的措施。     

Data mining of resilience indicators

In recent years, the Asia-Pacific region has experienced several financial setbacks, including speculative attacks in 1998 and the SARS outbreak in 2003. Financial stresses of this nature are unanticipated, and not all of the dangers can be predicted by the examination of market information and macroeconomic indicators. The Early Warning System (EWS) that has been adopted by the International Monetary Fund may not be able to predict future financial crises for all possible scenarios, because shocks come in many different forms. To supplement the EWS, this paper proposes a data mining framework to measure the resilience of an economy. The resilience framework does not predict a crisis, but rather assesses the current state of health of an economy and its ability to withstand a financial shock should one occur. The framework is based on a feedback system consisting of two stages. The first stage assigns a resilience score to each economy based on a fuzzy logic scoring scheme that is built on the ambiguous reasoning of experts. The second stage uses the classification tree approach to estimate thresholds for each economic indicator, and examines the quality of the fuzzy score. The result from the second stage is then passed back to the first stage as feedback. The final result is obtained when the feedback system reaches its equilibrium state. The proposed resilience framework is applied to the external-sector and the public-sector economies of several countries to illustrate its applicability.     

Line balancing in a just-in-time production environment: balancing multiple U-lines

The introduction of multiple, independent production lines has helped many firms to increase their production flexibility, provide for redundancy when equipment breaks down, reduce idle time and labor costs, and achieve many other benefits. This paper introduces and formalizes the multiple U-line balancing problem. Optimal solution methodologies are provided for Type I (minimize the number of stations for a given cycle time), Type II (minimize the cycle time for a given number of stations), and cost-minimization line-balancing problems. A branch-and-bound algorithm is also developed for the situation in which equipment requirements are dependent on the line configuration and the task assignment to stations. Computational results indicate that the greatest benefit of exploiting multiple lines occurs for smaller cycle-time problems that require higher output.     

Influence of the Transport Properties of the Crystal/Heat Transfer Surface Interfacial on Fouling Behavior

One method to reduce fouling is to extend the induction time by a defined modification of the interfacial interactions between the heat transfer surface and the crystalline deposit. Since these interactions are a result of both molecular and mechanical forces, two approaches for fouling mitigation have been developed: (a) Modification of the energy related properties of the heat transfer surface and (b) Modification of the geometry related properties of the heat transfer surface.     

箱包风格设计及其发展趋势(Ⅰ)

本文主要讨论现代箱包设计的风格定位及其流行趋势。     

Thermomechanical stress fields in high-temperature fibrous composites. I: Unidirectional laminates

This two-part paper presents a closed-form procedure for evaluation of estimates of local thermomechanical stress fields in two-phase fibrous composites and laminates. The first part is concerned with a unidirectional elastic laminate subjected to uniform mechanical loads and to uniform changes in temperature. Both phases are assumed to be elastic, with temperature-dependent moduli and expansion coefficients; the solution reflects the influence of thermomechanical interactions. Exact solutions are not possible for any real system, because the local geometry is not known in detail. Instead, estimates of the fields are found from a modified Mori-Tanaka approximation. Examples are presented for two SiC/Ti---Al---Nb composites. Local stresses of interest are found after cooling from fabrication to room temperature. The presence of local yielding, and the influence of coupling terms on the local stress magnitudes are examined. Extension of the results to laminated plates is presented in Part II (Dvorak, G.J., Chen, T. & Teply, J., Composites Science and Technology, 43 (1992) 359–368, this issue).     

Photoresponsive peptide and polypeptide systems: part II. Photochromism of poly(l-ornithine) containing various azo-contents in side chains

Poly(L-ornithine)s having various azo-contents in the side chains were synthesized by the water-soluble carbodiimide procedure. The photochemical properties of the polypeptides poly[N^δ-p-(phenylazo)benzoyl-L-ornithine] (PPABLO) containing 3–77 mol% azobenzene were investigated by absorption and circular dichroism spectroscopy in hexafluoro-2-propanol (HFIP) or water, and in HFIP-water or methanol-water solvent mixtures. The photochromism of the dichroic bands of the PPABLOs containing 20–77 mol% azobenzene in the visible and ultraviolet wavelength regions was found to be mostly reversible as a function of irradiation time at different wavelengths due to the photostationary state (above 80% trans-cis photoisomerization) of the azo aromatic moieties. The PPABLO containing 3.2 mol% azobenzene in water exhibited conformational changes from random coil to helix by the addition of methanol or sodium dodecyl sulphate (SDS). The photo-induced conformational change was observed in HFIP-water-SDS solvent mixtures, while no conformational change was seen in water and HFIP-water solvent mixtures.