Effect of electric field on the hydrodynamics of fluidized nanoparticles

The effect of electric field on the hydrodynamics of nanoparticles was studied in a fluidized rectangular bed, with electrodes attached to two parallel walls. It was shown that the electric field of the order of 3 times the gravity markedly decreased the bed expansion and increased the solids volume fraction of nanoparticles fluidized by air. In these experiments, a light diode assembly was utilized to infer the local solids volume fractions within a rectangular bed of 10 nm silica particles. These experimental measurements yielded a two dimensional solids volume fraction distribution within the rectangular bed. The experimental results provided some new insights into the distribution of solids within the bed. The agglomerate diameters were computed using a momentum balance with the drag given by the Ergun equation and the empirical Richardson-Zaki method. Both methods yielded agglomerate diameters of the order of 100 μm and showed dependence on the strength of the electric field. The electric field decreased the granular temperature of the nanoparticles.     

Drying Kinetics of a Porous Spherical Particle and the Inversion Temperature

A model is presented for drying of a single porous particle with superheated steam and humid air. Experimental data for spherical porous ceramic particle reported in the literature were used for the validation of the model. An inversion temperature at which the evaporation rates within superheated steam and humid air are equal was predicted. The effect of thermophysical properties of the particle (permeability 10^-14 - 10^-17 m², diameter 3 × 10^-3 - 10 × 10^-3 m) and operating variables (gas mass flux 0.26 - 0.78 kg m^-2 s^-1, drying agent temperature 120-200°C) is tested. The inversion temperature is shown to be affected by the thermophysical properties of the porous particle and of the drying agent.     

烧结处理小矿山精矿的应用研究

研究小矿山精矿的性质，分析小矿山精矿对烧结过程的影响，提出了增加小矿山精矿配入量的途径及方法．     

Low temperature synthesis of aluminium titanate by an aqueous sol-gel route

Formation of aluminium titanate (AT) has been achieved at low temperature through sol-gel process using boehmite and titanium hydroxide as precursors by controlling the particle size at nanoscale followed by in-situ peptisation. The formations of AT phase, particle size distributions, sintering and thermal expansion characteristics, and microstructural features have been reported. DTA and XRD analysis have been performed to confirm the formation of AT. A 94% relative density was obtained for aluminium titanate sintered at 1550 °C with controlled grain size in the range of 2-3 μm.     

Ozonation of CI Reactive Black 5 using rotating packed bed and stirred tank reactor

This study investigates the ozonation of CI Reactive Black 5 (RB5) by using the rotating packed bed (RPB) and completely stirred tank reactor (CSTR) as ozone contactors. The RPB, which provides high gravitational force by adjusting the rotational speed, was employed as a novel ozone contactor. The same ozone dosage was separately introduced into either the RPB or the CSTR for the investigation, while the experimental solution was continuously circulated within the apparatus consisting of the RPB and CSTR. The decolorization and mineralization efficiencies of RB5 in the course of ozonation are compared for these two methods. Moreover, the dissolved and off‐gas ozone concentrations were simultaneously monitored for the further analysis. As a result, the ozone mass transfer rate per unit volume of the RPB was significantly higher because of its higher mass transfer coefficient and gas–liquid concentration driving force. Furthermore, ozonation kinetics was found to be independent of the gravitational magnitude of an ozone gas–liquid contactor. Therefore, the results suggest employing RPBs as ozone‐contacting devices with the advantage of volume reduction. The experimental results, which can be used for further modeling of the ozonation process in the RPB, also show the requirement of correct design for the RPB. Consequently, the present study is useful for the understanding of practical application of RPBs. Copyright © 2004 Society of Chemical Industry     

新取代苯基荧光酮试剂的合成及其性质的研究Ⅱ．新型取代苯基荧光酮与金属离子显色反应的研究

研究了３，５－二溴－４－氨基苯基荧光酮、３，５－二溴－４－偶氮变色酸等８种苯基荧光酮在酸性介质中与高价金属离子Ｚｒ（Ⅳ）、Ｍｏ（Ⅵ）、Ｗ（Ⅵ）、Ａｌ（Ⅲ）、Ｇａ（Ⅲ）等的显色反应。３，５－位二溴取代的试剂的灵敏度高于未取代的灵敏度，摩尔吸光系数绝大多数在１０５Ｌ·ｍｏｌ－１·ｃｍ－１以上。     

Stable Oxygen and Carbon Isotopic Compositions of Lates stappersii Otoliths from Lake Tanganyika,East Africa

In this study, we measured growth trends in oxygen and carbon isotopic ratios in whole sagittal otoliths from three adult centropomid fish (Lates stappersii) from each of three sub-basins of Lake Tanganyika, East Africa. Sampling density was 20 to 50 samples per otolith. Both δ¹⁸O and δ¹³C values increase with age. The δ¹⁸O data suggest that otoliths were precipitated near the expected equilibrium with the ambient environment (ca. +3.5‰) and support a migration pattern from surface waters during larval stages to deeper waters (40 to 80 m) for mature fish. Relatively high δ¹⁸O values in the southern sub-basin are consistent with cooler temperatures in the region during seasonal upwelling. The δ13C increase from otolith core to edge is large (up to 4‰) and is interpreted as due to ontogenetic changes in diet and contributions from a decrease in the proportion of respired CO₂ incorporated into otolith carbonate as metabolic rates of the fish dropped with maturity. The data seem to successfully reveal life strategy and migration patterns of L. stappersii, document regional differences in lake conditions, and provide a record of temperature within the water column during which the fish lived. Higher resolution studies and analyses of historical samples could be used to constrain modern and past growth patterns, and to reconstruct past temperature gradients and productivity patterns in the lake.     

Improvement of levitation characteristics in a magnetic bearing system using HTSC‐permanent magnet hybrid structure

Magnetic bearing using pinning force of a permanent magnet and a high‐temperature superconductor has been developed. Additional permanent magnet is introduced to increase the levitation force of the magnetic bearing. In this hybrid magnetic bearing system, levitation force is mainly given by the repulsive force of the permanent magnets, and stability for the lateral direction is given by pinning force of the superconductor. The experimental device is developed. A ring‐type superconductor and a bulk one are examined. Levitation characteristics of the hybrid magnetic bearing are measured. The bulk superconductor shows better characteristics of both levitation and lateral stability than the ring one. Levitation force of the hybrid system becomes about twice as large as that of the nonhybrid one. Although, the repulsive force of the permanent magnet decreases the lateral stability of the system, its influence becomes small by choosing an adequate position of the permanent magnets and the superconductor. © 2004 Wiley Periodicals, Inc. Electr Eng Jpn, 150(1): 71–77, 2005; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.10350     

建(构)筑物机械拆除方法综述

介绍了几种常用的建(构)筑物机械拆除方法,对其工作原理、特点、应用条件及局限性加以分析和说明。     

Steady-state torque control system with secondary-current feedback for three-phase squirrel-cage induction motors

This paper presents a highly stable steady-state torque control system with a feedback of a secondary current signal. The torque control system is constructed with a feedback of the secondary current (I₂) signal using a quick response magnetic-field sensor constructed with an amorphous core multivibrator bridge, which can solve the secondary resistance change problem for temperature variation in the IM. Moreover, we added a state feedback to the system to improve the response speed for the unit step function of a torque order. The I₂ sensor method has advantages especially at a low-speed range, in which conventional method using an integrator shows control errors.