Solid state interfacial reactions in electrodeposited Ni/Sn couples

Ni/Sn couples,prepared by sequentially electroplating Ni layers and Sn layers on metallized Si wafers,were employed to study the mierostructures and growth kinetics of Ni-Sn intermediate phases,when the Ni/Sn couples were aged at room temperature or annealed at temperatures from 150 to 225℃for various times.The results show that the NiSn phase and Ni_3Sn_4 phase are formed,respectively,in the aged couples and annealed couples.The Ni_3Sn_4 layer is continuously distributed between the Ni and Sn sides in t...     

有限体积法求解立体角离散误差

为解决采用有限体积法求解辐射传输方程时引起离散误差的问题,从有限体积法立体角内热流密度的求解过程出发,运用泰勒级数推导了近似误差的表达式,并分析影响离散误差的各种因素,包括离散射线数,辐射强度分布,假散射及网格比.根据分析结果,采用辐射强度的连续分布模型,模拟了各种因素对误差的影响.结果表明,辐射强度的分布函数对于有限体积法的离散误差有一定程度影响.当增加网格数及减小网格尺寸比时,可以有效地减小离散误差.假散射与离散误差间呈较强的非线性耦合关系.     

Highly ion-conductive solid polymer electrolytes based on polyethylene non-woven matrix

Highly ion-conductive solid polymer electrolyte (SPE) based on polyethylene (PE) non-woven matrix is prepared by filling poly(ethylene glycol) (PEG)-based crosslinked electrolyte inside the pores of the non-woven matrix. The PE non-woven matrix not only shows good mechanical strength for SPE to be a free-standing film, but also has very porous structure for high ion conductivity. The ion conductivity of SPE based on PE non-woven matrix can be enhanced by adding sufficient non-volatile plasticizer such as poly(ethylene glycol) dimethyl ether (PEGDME) into ion conduction phase without sacrificing mechanical strength. SPE with 20 wt.% crosslinking agent and 80 wt.% non-volatile plasticizer shows 3.1 × 10⁻⁴ S cm⁻¹ at room temperature (20 °C), to our knowledge, which is the highest level for SPEs. It is also electrochemically stable up to 5.2 V and has high transference number about 0.52 due to the introduction of anion receptor as an additive. The interfacial resistance between Li electrode and SPE is low enough to perform charge/discharge test of unit cell consisting of LiCoO₂/SPE/Li at room temperature. The discharge capacity of the unit cell shows 87% of theoretical value with 86% Coulombic efficiency.     

Electrochemical and microstructural characterization of cyclic redox behaviour of SOFC anodes

The oxidation of Ni to NiO in solid oxide fuel cell (SOFC) anode will result in large bulk volume change, which may change the interfaces of the two phases in the anode cermet and thus may cause significant performance degradation. The reduction and oxidation (redox) of the Ni/YSZ cermet were studied at 800 ℃. Anodic polarization measurements were performed before and after redox cycles. The anode current density at an overpotential of 100 mV kept decreasing during the whole redox treatment. It decreased from 19.11 to 7.95 mA·cm-2 after two redox cycles. Anode supported unit cell was assembled for cell's discharge measurements. Cell performance declined after each redox cycle. The maximum power density decreased from 126.28 to 40.32 mW·cm-2 . The microstructural changes after redox cycling were recorded using scanning electron microscopy (SEM). The results reveal that after re-oxidation, the Ni gets coarse and has a higher porosity; the nickel network structure turns to be desultory.     

Abnormal Austenite-Ferrite Transformation Behaviors of Fe-ISi: Dilatometric Measurements

WITH THE APPEASING of competition of the totaloutput of iron and steels, the new generation of ultrahigh strength steel, based on the lessen the burden ofenvironment, double improvement of mechanicalproperties and elongation of the serving life, has beenfully outspreaded in the world. More and more researchwork shows that the solid-state microstructureevolution becomes the most effective route in thedevelopment of ultra-high strength steels. A process ofgreat interest in the steel produc…     

Electrochemical corrosion behavior of 2A02 Al alloy under an accelerated simulation marine atmospheric environment

The corrosion behavior of 2A02 Al alloy under simulated marine atmospheric environment has been studied using mass-gain, scanning electron microscope/energy dispersive spectroscopy (SEM/EDS), laser scanning confocal microscopy, X-ray diffraction spectroscopy and localized electrochemical methods. The results demonstrate that the relationship between the corrosion induced mass-gain and the corrosion time is in accordance with the power rule. The mass-gain increases gradually during the corrosion time, while the corrosion rate decreases. With ongoing of the corrosion, corrosion products film changed from a porous to a compact structure. The various spectroscopic data show that the corrosion products films composed mainly of Al(OH)₃, Al₂O₃ and AlCl₃. The electrochemical corrosion behavior of the 2A02 Al alloy was studied by electrochemical impedance spectroscopy (EIS).     

Direct numerical simulations for assessment of gas-solid drag models in two-dimensional random arrays of particles

The momentum exchange between the phases plays a vital role in modelling of gas–solid flows and it is mathematically described by drag models. However, no consensus exists on which drag model gives the most accurate prediction of the drag force, and, despite the increase in available computing power, the same drag models are used in two-dimensional and three-dimensional simulations. In this study, direct numerical simulations of gas flow through multiple random configurations of static monodisperse particles are performed. The variations of solid volume fraction and particle Reynolds number are in the ranges of 0.05–0.4 and 13.7–136.9, respectively. The drag force exerted on particles is calculated and properly averaged. Based on the simulation results, thirteen drag models are compared and correction factors are introduced using the stochastic gradient descent algorithm. The correction factors provide a simple adjustment for the models to be used in 2D modelling.     

Quasiconvolutional smoothing of polyhedra

This paper describes a method for rounding edges and corners of arbitrary polyhedra that uses a fast approximation to convolutional filtering. The approximation defines an implicit surface, which is rendered with a specialised ray-tracing algorithm. By varying the radius of the smoothing filter, a wide range of effects can be obtained, from perfect polyhedra to blobby models. Small rounding radii give polyhedra a softer, more natural look, with edges well delineated by shadows and highlights. The rounded surfaces are much easier to specify and compute than those obtained by traditional filleting and surface-blending techniques, and are far more economical in storage.     

Dynamics of polymer electrolyte fuel cells undergoing load changes

Numerical simulations are carried out for a single-channel polymer electrolyte fuel cell (PEFC) undergoing a step increase in current density. The objective is to elucidate profound interactions between the cell voltage response and water transport dynamics occurring in a low-humidity PEFC where the membrane hydration and hence resistance hinges upon the product water. Detailed results are presented to show that a step increase in the current density leads to anode dryout due to electroosmotic drag, while it takes several seconds for water back-diffusion and anode humidified gas to re-wet the anode side of the polymer membrane. The water redistribution process is controlled by water production, membrane hydration, electroosmotic drag, and water diffusion in the membrane. The anode dryout results in a substantial drop in cell voltage and hence temporary power loss. Under extreme situations such as dry anode feed, large step increase in the current density, and/or lower temperatures, the cell voltage may even reverse, resulting in not only power loss but also cell degradation. Finally, the dynamics of current distribution after a step change in gas humidification is numerically examined.     

医用电解质分析仪的研制

对医学常规体液检查中5种离子浓度的检测,利用单片机、高精度A/D芯片、实时时钟等,给出了一种切实可行的解决方案,并详细地阐述了系统的软硬件设计。