水性聚氨酯电导率与聚沉值的研究

研究了软（硬）段含羧基的水性阴离子纳米聚氨酯体系的n(NCO)/n(OH)比值，COOH的质量分类，反离子各类，合成方法与电导率关系及产生的原因；探讨了该体系的n(NCO)/n(OH)值，COOH的质量分数，合成方法与临界聚沉值（Cc.c)的关系和规律。并分析，比较了软（硬）段含羧基的水性阴离子聚氨酯体系电导率与Cc.c二者关系，得出了随COOH的质量分数升高，二者变化相同，随n(NCO)/n(OH)比值升高,二者变化相反的结论。     

Magnetic field hysteresis of critical currents in Bi(2223)/Ag tapes and a way to overcome it

Experiments showing hysteresis of critical currents versus the external magnetic field I_c(B_e) were performed with two multifilamentary Bi(2223)/Ag tapes. The I_c(B_e) hysteresis is observable in the transversal as well as in the longitudinal orientation of the long axis of the tape with respect to the magnetic field. Based on the idea that the hysteresis is the effect of trapped flux in a network of well-connected current paths, a way to overcome this effect has been proposed and experimentally verified. The induced frozen-in screening currents are split into several parallel current patterns by cycling the external magnetic field around the adjusted value. Using the proposed method, the ‘neutral’ I_c(B_e) characteristics have been found. Approximate calculations of the penetration depth of the trapped flux show that the network of well-connected current paths could be formed by several disk-shaped grains (≈ Φ8 × 0.4 μ) stacked into more or less axially ordered (quasi cylindrical) colonies of average dimensions estimated to ≈ Φ8 × 4 μm.     

Effects of shear flow on long-ranged correlations,spinodal demixing kinetics,and the location of the critical point and cloud point

A derivation of an expression for the shear rate-dependent Ornstein Zernike structure factor is discussed, together with the resulting anomalous behavior of the turbidity. The predicted scaling behavior of the turbidity, comprising the effect of both temperature and shear rate, is in good agreement with experiments on binary fluids. Then initial spinodal decomposition is discussed, and an explicit expression for the time- and shear rate-dependent effective diffusion coefficient is derived, which shows all the typical characteristics of anisotropic light scattering patterns that are observed experimentally for binary fluids. Next it is shown that the spinodal is shifted linearly with the (bare) Peclet number for not too large Peclet numbers, whereas the cloud point is singularly displaced into the unstable region due to a shear now. This is in agreement with an experiment on a two-polymer/solvent mixture and binary fluid mixtures. It is argued that light scattering is useless to determine the location of the spinodal of a sheared system.Paper presented at the Twelfth Symposium on Thermophysical Properties, June 19–24, 1994, Boulder, Colorado, U.S.A.     

Rhizobium trifolii capsular polysaccharide: a novel biopolymer with striking physical properties

The physical properties of the capsular polysaccharide of Rhizobium Trifolii (CPS) were investigated. Viscosity measurements provided information about the hydrodynamic volume of single coils, the perturbation of solvent flow and the shear-thinning behaviour of concentrated solutions. Changes in chain geometry and the development of an intermolecular network as a function of temperature were monitored using the techniques of optical rotation and dynamic oscillation. Finally, analysis of calorimetric thermograms elucidated the type of interactions between CPS and the bacterial levan. Overall, the Rhizobium polysaccharide was found to form thermally-reversible gels at an extremely low 'minimum critical gelling concentration' (c_o∼ 0.35gl^-1). At temperatures above the gel melting point (∼ 48°C), however, the compact polymer coils entangled at comparatively high concentrations (about 60 times higher than c_o). In the presence of a highly branched levan, the thermal stability of ordered CPS structures increased as a consequence of thermodynamic incompatibility between the two polymers.     

Fabrication and characteristics of tapes and test magnets made from Ag-Clad Bi-2223 superconductors

Pb_0.4Bi_1.8Sr₂Ca_2.2Cu₃O_x (Bi-2223) precursor powder was prepared by a solid-state reaction of carbonates and oxides of lead, bismuth, strontium, calcium, and copper, and the powder was then used to fabricate silver-clad tapes by the powder-in-tube technique. Transport critical current density (J_c) values>4×10⁴ A/cm² at 77K and 2×10⁵ A/cm² at 4.2 and 27K have been achieved in short tape samples. Long lengths of tape were tested by winding them into pancake coils. Recently, we fabricated a test magnet by stacking ten pancake coils, each containing three 16m lengths of rolled tape, and tested it at 4.2, 27 and 77K. A maximum generated field of 2.6 T was measured in zero applied field at 4.2K and the test magnet generated significant self-field in background fields up to 20 T. The results are discussed in this paper.     

Dependence of critical current density on microstructure and processing of high-Tc superconductors

Microstructural origins for reduced weak-link behavior in high-J_c melt-processed YBCO, spray pyrolyzed thick films of Tl-1223, metallic precursor Y-124 polycrystalline powder-in-tube (PIT) wires and PIT Bi-2212/2223 are discussed. Since the materials studied are the highest J_c, polycrystalline, high-T_c superconductors fabricated worldwide, the results provide important guidelines for further improvements in superconducting properties, thereby enabling practical applications of these materials. It is found that strongly linked current flow within domains of melt-processed 123 occurs effectively through a single crystal path. In c-axis oriented, polycrystalline Tl-1223 thick films, local in-plane texture has been found to play a crucial role in the reduced weak-link behavior. Formation of “colonies” of grains with a common c-axis and modest in-plane misorientation was observed. Furthermore, a colony boundary in general has a varying misorientation along the boundary. Large regions comprised primarily of low angle boundaries were observed. Percolative transport through a network of such small angle boundaries appears to provide the nonweak-linked current path. Although powder-in-tube BSCCO 2212 and 2223 also appear to have a “colony” microstructure, there are some important differences. Colonies in BSCCO consist of stacks of grains with similar c-axis orientation in contrast to colonies in Tl-1223 films where few grains are stacked on top of one another. Furthermore, most grains within a colony in BSCCO have the same lateral dimensions as that of the colony, resulting largely largely in “twist” boundaries. Further microstructural characterization of high-J_c PIT 2212 and 2223 is currently underway. In the case of Y-124 wires, weak macroscopic in-plane texture is found. Additional measurements are underway to determine if a sharper, local in-plane texture also exists. It is found that in three of the four types of superconductors studied, reduced weak-link behavior can be ascribed to some degree of biaxial alignment between grains, either on a “local” or a “global” scale.     

A New Variable Diffusion Drying Model for the Second Falling Rate Period of Paddy Dried in a Rapid Bin Dryer

The objectives of this article is to propose a new drying model for the second falling rate period known as the variable diffusion controlled period that follows after the first falling rate period and to propose a new method to determine the second critical moisture content that separates these two periods. Experimental work on paddy drying at minimum fluidization velocity was carried out in a rapid bin dryer. The effects of operating temperatures (60-120°C) and bed depths (2-6 cm) on the paddy drying characteristics were investigated. It was found that the normalized drying rate of paddy was proportional to the normalized moisture content in the first falling rate period but in the second falling rate period, the normalized drying rate of the material varies exponentially with the normalized moisture content. The different relationship between the normalized drying rate and the normalized moisture content in the first and second falling rate periods indicate that two different mechanism of moisture transport are at work. The new exponential model of the second falling rate period and the linear model of the first falling rate period were found to fit the experimental data very well. Derivation from variable diffusion equation shows that the linear model is the result of constant diffusion coefficient whereas the new exponential model is the result of linear diffusion coefficient. This also implies that the first falling rate period is a constant diffusion controlled period and the second falling rate period is a variable diffusion controlled period. In addition, drying kinetics data of a drying process that fits the exponential model over a very slow drying period will show that the drying process is under the effect of a linear diffusion coefficient. It was also found that the proposed new method to determine the second critical moisture content that distinguishes between the first and second falling rate periods by using a sudden change in the value of the drying rate gradient to a much lower value at that point is more rigorous and yet simpler than the method of determining the specific location of the receding drying boundary since it is based on the behavior of the actual drying kinetic data.     

Phase equilibria of quasi-binary systems consisting of multicomponent polymers 1 and 2. IV: Poly(ethylene oxide)/poly(propylene oxide) systems

To confirm the reliability of the theory of phase equibria of multicomponent polymer 1/multicomponent polymer 2 systems (i.e. quasi-binary systems) and the method of computer experiment based on this theory (Brit. Polym. J., 23 (1990)285; 23 (1990)299; Polym. Int., 29 (1992)219), could point curves (CPC), two-phase volume ratios ( R ) and critical solution points (CSP) have been determined experimentally for the quasi-binary mixtures of poly(ethylene oxide) (M¯_w = 647, M¯_w/M¯_n = 1.15; M¯_w and M¯_n, the weight-average and numberaverage molecular weights, respectively) and poly(propylene oxide) (M¯_w = 2028, M¯_w/M¯_n = 1.08; and M_w = 2987, M_w/M_n = 1.13). The hydroxyl end groups of both polymers were methoxylated in advance by the Cooper & Booth method (Polymer, 18 (1977)164). The thermodynamic interaction parameter between both polymers, χ₁₂, and the concentration dependence parameters for the above quasi-binary systems were determined by the method proposed in a previous paper (Brit. Polym. J., 23 (1990)299). CPC, R and CSP values calculated on the basis of the theory are in good agreement with the values determined experimentally.     

集中载荷作用下的套管抗挤能力分析

根据油田套管损坏情况,建立了集中载荷作用下的套管抗挤能力计算模型,利用能量法和曲杆理论,分析研究了承受180°对称分布集中载荷、90°均匀分布集中载荷和120°均匀分布集中载荷下中厚壁套管抗挤能力,得出了理想圆管抗挤强度和套管屈曲临界挤毁压力的计算公式,通过分析比较理论解与有限元解,其最大相对误差不超过1%,得出了套管抵抗局部载荷的能力低于抵抗均布载荷的结论。     

Critical incidents and chronic stressors at work: Their impact on forensic doctors.

Workers in medium- or high-risk professions are often confronted with critical incidents at the workplace. The impact of these acute stressors may be serious and enduring. Many workers also experience chronic job stressors, such as work overload or role conflicts. This study examined the frequently neglected relationship of acute and chronic stressors with self-reported health symptoms, such as posttraumatic responses, fatigue, and burnout. This association was investigated in a sample of forensic doctors in the Netherlands (N = 84). It was found that the more traumatic events the respondents experienced, the more problems they reported in coping with the traumatic events. Chronic job stressors were associated with posttraumatic responses (intrusions and avoidances) and with burnout and fatigue. (PsycINFO Database Record (c) 2010 APA, all rights reserved)