Strain analysis of moving objects using a Fourier transform grid method

There is no good method to measure the shape and the strain distributions of a structure changing with time. We have previously proposed the Fourier transform grid method (FTGM) to measure the three-dimensional shape and surface strain distributions of stationary objects by analysing the two-dimensional grating images recorded with two cameras. In the stereoscopic method, it is very important to determine the accurate geometric parameters of the camera system. In this paper, the positions and the directions of cameras are accurately determined using the FTGM applied to images of a reference object on which a two-dimensional grating is drawn. Applications for analysing shape and strain distributions of vibrating rubber plates and a moving human skin are shown.     

A sensorless brushless dc motor system

This paper describes a brushless dc motor system without position or speed sensor. The brushless motor consists of a permanent magnet synchronous motor and a voltage-source inverter capable of controlling the amplitude and frequency of voltage. The rectangular-shaped stator current with a conducting interval of 120° (electrical) is controlled to be in phase with the trapezoidal back electromotive force. This results in producing maximum torque. Variable speed is achieved by adjusting the average motor voltage similarly to chopper control of dc motors. In this paper, two sensorless position detecting methods, i.e., an “indirect method” suited for the lower-speed range and a “direct method” suited for the higher-speed range are proposed. The combination of the two makes it possible to detect the rotor position over a wide-speed range. Furthermore, a speed-sen-sorless PLL control is proposed in applying the principle of the direct method. Experimental results obtained from a prototype brushless dc motor are shown to confirm the validity of the sensorless drive. The starting procedure of the motor also is discussed because it is impossible to detect the rotor position at a standstill.     

Improvement of levitation characteristics in a magnetic bearing system using HTSC‐permanent magnet hybrid structure

Magnetic bearing using pinning force of a permanent magnet and a high‐temperature superconductor has been developed. Additional permanent magnet is introduced to increase the levitation force of the magnetic bearing. In this hybrid magnetic bearing system, levitation force is mainly given by the repulsive force of the permanent magnets, and stability for the lateral direction is given by pinning force of the superconductor. The experimental device is developed. A ring‐type superconductor and a bulk one are examined. Levitation characteristics of the hybrid magnetic bearing are measured. The bulk superconductor shows better characteristics of both levitation and lateral stability than the ring one. Levitation force of the hybrid system becomes about twice as large as that of the nonhybrid one. Although, the repulsive force of the permanent magnet decreases the lateral stability of the system, its influence becomes small by choosing an adequate position of the permanent magnets and the superconductor. © 2004 Wiley Periodicals, Inc. Electr Eng Jpn, 150(1): 71–77, 2005; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.10350     

Bayes estimators for reliability measures in geometric distribution model using masked system life test data

This paper presents Bayes estimators for the reliability measures of the individual components in a multi-component systems in the presence of masked system life test data. The life time distributions of the system components are assumed to be geometric with different parameters. Two-sided Bayesian probability intervals of the parameters are also derived. Numerical simulation study is given in order to: (i) explain how one can apply the theoretical results obtained, (ii) study the influence of the sample size and masking level on the accuracy of point estimates.     

Powder Deposition in Three Parallel-Oriented Dies of Different Shapes

Uniformity of bulk density distribution during the die filling process is required to minimize quality problems, such as distortion and cracking, for powder compacts. Understanding the die filling process is necessary in ensuring a uniform powder deposition. The second-generation pressure deposition tester (PDT-II) was used to investigate the deposition process and final pressure distribution of powder filling in toroidal, cylindrical, and E-shaped dies. All tests were conducted using a spray-dried free-flowing granular powder. The results indicated that for toroidal dies: (1) the area around 0° orientation (the leeward end) had the highest pressure values (1186.7 to 2498.0 Pa), with the average pressure values of the remaining area 353.7-648.0 Pa; (2) the pressure distribution was symmetrical about the centerline parallel to the feed shoe movement direction; (3) the highest feed shoe speed (500 mm/s) led to the most nonuniform pressure distribution among the three speeds; (4) higher feed shoe speed did not always result in higher final pressure values; and (5) the right die tended to have higher final pressure values (215.0 to 2498.0 Pa) than the center die (95.4 to 2052.5 Pa). For E-shaped dies: (1) the final pressure values of the middle leg (308.9 to 760.7 Pa) were higher than those of the left and the right legs (148.9 to 530.3 Pa); (2) the area along the backside had the highest final pressure value (1054.6 to 1303.8 Pa); (3) the pressure distribution was symmetrical about the centerline parallel to the feed shoe movement direction; and (4) neither the center die nor the right die always had higher pressure values than the other one at all locations. Comparison between cylindrical and toroidal dies indicated that: (1) neither of the two die shapes (cylinder and toroid) led to consistently higher or lower final pressure values at all locations and (2) for all three feed shoe speeds, the toroidal die had higher average final pressure values in the 0° orientation.     

Non-steady-state model for kinetics of free radical polymerization, 4. Direct thermal initiation

This paper deals with the non-steady-state kinetics of direct thermal initiated polymerization. The initiation is assumed to be a bimolecular reaction of the monomer. The relationship between the radical concentration and the monomer conversion is rigorously derived. In further treatment a few very close approximations are introduced based on the fact that the number of monomer molecules reacting in the initiation step is much less than that consumed in the propagation step for a process producing high polymer, and the value of the rate constant for propagation or chain transfer is much lower than that for chain termination. Expressions for various molecular parameters, such as molecular weight distribution, number-average and weight-average degrees of polymerization, and dispersity, are given. Several numerical examples are provided.     

Observation of atomic steps on CaCO3 crystal surface

By using scanning polarization force microscopy,the deliquescence process and the atomic steps on the cleavage surface of CaCO3 in air were studied in situ.Under an exposure to medium umidity(-57%),the sloiw step movement has been observed.     

镨掺杂分布对1.3μm光纤放大器特性影响

对掺氟化镨玻璃光纤放大器的小信号增益，用广义的高斯近似公式可获得精确的分析表达。文中研究了限制光纤芯层中央部分的镨掺杂对光纤放大器特性的影响，结果发现限制镨掺杂分布能改进光纤放大器的工作效率，且截止波长比芯层全部均匀掺镨的光纤更长。     

Finite Element Analysis of a Moving Boundary Value Problem

A finite element formulation and the solution of a set of nonlinear coupled heat and mass transfer equations for a two-phase system with a moving evaporation interface is presented. The interface condition takes into account the moisture transfer balance at the moving boundary. The finite element results were compared with existing results for a single phase system for model validation. In the two-phase system, the movement of evaporation front has an appreciable effect on the temperature and moisture distribution inside the porous medium during drying. The effect of the nondimensional heat of vapourization parameter γ on the evaporation front, temperature and moisture distribution in porous medium was studied. The higher the value of γ, the slower is the movement of the evaporation front. The temperature decreased and the moisture content increased as the nondimensional vapourization parameter γ increased. This model has potential applications in studying the heat and mass transfer characteristics in food and biomaterials.     

Air Filtration and Radon Decay Product Mitigation

Air cleaning as a means of mitigating the risks arising from exposure to indoor radon progeny has been evaluated in a single-family house in the north eastem US. using an automated, semi-continuous activity-weighted size distribution measurement system. The measurements included radon concentration, condensation nuclei count, and activity-weighted size distribution of radon decay products. Measurements were made in the house with and without an operating air filtration system and with various particle sources common to normal indoor activities operating. Aerosols were generated by running water in a shower, candle burning, cigarette smoking, vacuuming, opening doors, and cooking. Using a room model, the changes in attachment rates, average attachment diameters, and deposition rates of the unattached fraction with and without the air cleaning system were calculated. In the presence of active aerosol sources, the air filtration unit typically reduced the concentration of particles within the hour following the end of particle generation. After candle burning, cigarette smoking, and vacuuming in the bedroom, the reductions of PAEC by air filtration are about 60% with the air filtration system operating in the bedroom. During cooking in the kitchen, the reductions of PAEC in the bedroom with the air filtration system were about 40%. However, for all cases the dose reductions were smaller than the particle and PAEC reductions. For those particles that were generated within the bedroom, there was a 20% to 50% reduction in dose. In the case of cooking where the door was open and particles infiltrated from the rest of the house, the dose reduction was only 5% on average and appears to be insignificant. Thus, the dose reductions were h e r than the reductions in activity concentration, but there were no cases where the estimated dose actually increased.