Mechanical alloying in the Al-Bi alloy system

Mechanical alloying (MA) was carried out to investigate the MA behaviour of the immiscible Al-10, 30 at % Bi alloys. After the MA processing, the Al and Bi were finely and homogeneously alloyed. The Bi crystallite size decreased to 25 nm and 30 nm in the Al-10 at % Bi and Al-30 at % Bi alloys, respectively. By increasing the MA time, the hardness increased up to a value of 80 H _v, which is larger than that obtained from the rule of mixtures. The lattice parameter of Bi decreased by about 0.27%, which shows the formation of a non-equilibrium hcp Bi super-saturated solid solution. The extended solubility of Al in Bi was 1.9% in the Al-30 at % Bi alloy. Due to the extended solubility, depression of the melting temperature of hcp Bi was confirmed in the mechanically alloyed Al-Bi alloys. The maximum depression in the temperature was about 10 K. The measured values corresponded well with those estimated from the extrapolation of the solidus line.     

Recovery retardation in equal channel angular pressed Al–Zr alloy during friction stir welding

The effect of Zr on reduction of hardness and microstructure in an FS weld of equal channel angular-pressed Al alloy was investigated. Zr addition to Al suppressed dynamic recovery in the thermomechanically affected zone and enabled retention of the high hardness of the ECA-pressed material throughout the weld.     

Distributed architecture for energy management D-structure

Electric power systems are expanding in size and complexity, and the requirement for the energy management system (EMS) is becoming more important. In this computer control system, a single control computer is used mainly as the primary computer and its software is very complicated because of its hugh number of small, quick tasks to obtain high response speed. Therefore, much effort is needed to develop and modify the programs, and the responsiveness of this centralized architecture varies greatly when many faults occur in the power system. This paper describes a new distributed architecture for the EMS. Distributed processors execute the functions cooperatively with periodic access to the common bulletin board database in which information about the power system exist. This architecture facilitates the software development and maintenance, and it also enhances the performance by the parallel processing of the distributed functions.     

Molecular characterization of a single mitochondria-associated double-stranded RNA in the green alga Bryopsis

OBJECTIVE: To evaluate the effect of a moderate dose of fish oil on glycemic control and in vivo insulin action in type 2 diabetic men with elevated plasma triacylglycerols and to determine the effect of the same treatment on gene expression of GLUT4, lipoprotein lipase (LPL), and hormone-sensitive lipase (HSL) in the abdominal adipose tissue. RESEARCH DESIGN AND METHODS: A total of 12 type 2 diabetic men were randomly allocated to 2 months of 6 g daily of either fish oil or sunflower oil, separated by a 2-month washout interval, in a double-blind crossover design. RESULTS: For glucose metabolism, 2 months of fish oil supplementation compared with sunflower oil led to similar fasting plasma insulin, glucose, and HbA1c. Basal hepatic glucose production did not increase after fish oil. There was no difference in insulin suppression of hepatic glucose production nor in insulin stimulation of whole-body glucose disposal measured by the euglycemic-hyperinsulinemic clamp. Fish oil did not ameliorate the low mRNA level of GLUT4 in adipose tissue of these patients. For lipid profile, fish oil lowered plasma triacylglycerol more than sunflower oil (P < 0.05) and tended to increase the amount of mRNA of both LPL and HSL in adipose tissue. CONCLUSIONS: A moderate dose of fish oil did not lead to deleterious effects on glycemic control or whole-body insulin sensitivity in type 2 diabetic men, with preserved triacylglycerol-lowering capacities.     

Separation of Polyvinyl Chloride from Plastic Mixture by Froth Flotation after Surface Modification with Ozone

Selective modification by ozonation for the surface of polyvinyl chloride (PVC) was evaluated to separate PVC from the other plastics, polyethylene terephthalate (PET), polycarbonate (PC) and polymethyl methacrylate (PMMA), with almost the same density as PVC by the froth flotation process. Ozonation could selectively decrease the contact angles of flexible PVC from 87.5 degrees to 68.4 degrees and rigid PVC from 90.3 degrees to 66.9 degrees, whereas little decreases in the contact angle were observed for other plastics. This would be due to the replacement of the chloride group on the surface of PVC, into hydrophilic functional groups; carbonyl, carboxyl and ester group. The PVC was successfully separated from the other plastics by the froth flotation process after the selective surface modification by ozonation.     

New class of cellulose fiber spun from the novel solution of cellulose by wet spinning method

A novel cellulose solution, prepared by dissolving an alkali-soluble cellulose, which was obtained by the steam explosion treatment on almost pure natural cellulose (soft wood pulp), into the aqueous sodium hydroxide solution with specific concentration (9.1 wt %) was employed for the first time to prepare a new class of multifilament-type cellulose fiber. For this purpose a wet spinning system with acid coagulation bath was applied. The mechanical properties and structural characteristics of the resulting cellulose fibers were compared with those of regenerated cellulose fibers such as viscose rayon and cuprammonium rayon commercially available. X-ray analysis shows that the new cellulose fiber is crystallographically cellulose II, and its crystallinity is higher but its crystalline orientation is slightly lower than those of other commercial regenerated fibers. The degree of breakdown of intramolecular hydrogen bond at C₃[X_am(C₃)] of the cellulose fiber, as determined by solid-state cross-polarization magic-angle sample spinning (CP/MAS) ¹³C NMR, is much lower than other, and the NMR spectra of its dry and wet state were significantly different from each other, indicating that cellulose molecules in the new cellulose fiber are quite mobile when wet. This phenomenon has not been reported for so-called regenerated cellulose fibers.     

Crystal Structure and Microwave dielectric Properties of Ba(Zn1/3Ta2/3)O3–(Sr,Ba)(Ga1/2Ta1/2)O3 Ceramics

The microwave dielectric properties and crystal structure of Ba(Zn_1/3Ta_2/3)O₃– (Sr,Ba)(Ga_1/2Ta_1/2)O₃ ceramics were investigated in the present study. The Q value of Ba(Zn_1/3Ta_2/3)O₃ was improved by adding 5 mol% Sr(Ga_1/2Ta_1/2)O₃. The maximum Q value of Q × f = 162000 GHz was obtained at 0.95Ba(Zn_1/3Ta_2/3)O₃. 0.05Sr(Ga_1/2Ta_1/2)O₃. For this composition, a lattice super structure caused by hexagonal ordering was observed. A further improvement in the Q value was attained when some Sr was replaced with Ba, and 0.95Ba(Zn_1/3Ta_2/3)O₃· 0.05(Sr_0.25Ba_0.75)(Ga_1/2Ta_1/2)O₃ exhibited a maximum Q value such that Q × f = 210000 GHz. Despite the increased Q value with the replacement of Sr by Ba, the c/a value, which indicates the degree of lattice distortion, remained constant near 3/2. The Q value thus improved without lattice distortion in the system Ba(Zn_1/3Ta_2/3)O₃-(Sr,Ba)(Ga_1/2Ta_1/2)O₃, whereas the improvement of Q value increased with lattice distortion in the solid solution system with Ba(Zn_1/3Ta_2/3)O₃ as an end member.     

Anatase-Type TiO2 and ZrO2-Doped TiO2 Directly Formed from Titanium(III) Sulfate Solution by Thermal Hydrolysis: Effect of the Presence of Ammonium Peroxodisulfate on their Formation and Properties

Anatase-type TiO₂ powder containing sulfur with absorption in the visible region was directly formed as particles with crystallite in the range 15–88 nm by thermal hydrolysis of titanium(III) sulfate (Ti₂(SO₄)₃) solution at 100°–240°C. Because of the presence of ammonium peroxodisulfate ((NH₄)₂S₂O₈), the yield of anatase-type TiO₂ from Ti₂(SO₄)₃ solution was accelerated, and anatase with fine crystallite was formed. Anatase-type TiO₂ doped with ZrO₂ up to 9.8 mol% was directly precipitated as nanometer-sized particles from the acidic precursor solutions of Ti₂(SO₄)₃ and zirconium sulfate in the presence and the absence of (NH₄)₂S₂O₈ by simultaneous hydrolysis under hydrothermal conditions at 200°C. By doping ZrO₂ into TiO₂ and with increasing ZrO₂ content, the crystallite size of anatase was decreased, and the anatase-to-rutile phase transformation was retarded as much as 200°C. The anatase-type structure of ZrO₂-doped TiO₂ was maintained after heating at 1000°C for 1 h. The favorable effect of doping ZrO₂ to anatase-type TiO₂ on the photocatalytic activity was observed.     

Porous poly(L‐lactic acid)/poly(ethylene glycol) blend films

Poly(L ‐lactic acid) (PLLA: M_w = 19.4 × 10⁴)/poly(ethylene glycol) (PEG: M_w = 400) blend films were formed by use of a solvent‐cast technique. The properties and structures of these blend films were investigated. The Young's modulus of the PLLA decreased from 1220 to 417 MPa with the addition of PEG 5 wt %, but the elongation at break increased from 19 to 126%. The melting point of PLLA linearly decreased with increases in the PEG content (i.e., pure PLLA: 172.5°C, PLLA/PEG = 60/40 wt %: 159.6°C). The PEG 20 wt % blend film had a porous structure. The pore diameter was 3–5 μm. The alkali hydrolysis rate of this blend film was accelerated due to its porous structure. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 94: 965–970, 2004     

Synthesis of thermosetting poly(phenylene ether) containing allyl groups

New thermosetting poly(2-allyl-6-methylphenol-co-2,6-dimethylphenol)s (3) have been developed by oxidative coupling copolymerization of 2-allyl-6-methylphenol (1) with 2,6-dimethylphenol (2), followed by thermal curing. Copolymerization was conducted in nitrobenzene in the presence of copper(I) chloride and pyridine as the catalyst under a stream of oxygen, producing high molecular weight copolymers (M_n∼50,000) with broad molecular weight distributions (M_w/M_n∼35). The structure of resulting copolymers 3 was characterized by IR, ¹H, and ¹³C NMR spectroscopy. Cross-linking reactions of copolymers were carried out by thermal treatment in the absence or presence of a peroxide (3 wt%, 2,5-dimethyl-2,5-di(tert-butylperoxy)-3-butane). The 10% weight loss and glass transition temperatures of the cured copolymers were 436 °C in nitrogen and 235 °C, respectively after curing at 70 °C for 1 h and 300 °C for 1 h. The average refractive index of the cured copolymer (3b) film was 1.5407, from which the dielectric constant (ε) at 1 MHz was estimated as 2.6. The ε and dissipation factor of copolymer-films at 1 MHz were directly measured from their capacitances as 2.5-2.6 and 0.0015-0.0019, respectively.