Nanomaterials for radiotherapeutics-based multimodal synergistic cancer therapy

Over the past decade, numerous studies have attempted to enhance the effectiveness of radiotherapy (external beam radiotherapy and internal radioisotope therapy) for cancer treatment. However, the low radiation absorption coefficient and radiation resistance of tumors remain major critical challenges for radiotherapy in the clinic. With the development of nanomedicine, nanomaterials in combination with radiotherapy offer the possibility to improve the efficiency of radiotherapy in tumors. Nanomaterials act not only as radiosensitizers to enhance radiation energy, but also as nanocarriers to deliver therapeutic units in combating radiation resistance. In this review, we discuss opportunities for a synergistic cancer therapy by combining radiotherapy based on nanomaterials designed for chemotherapy, photodynamic therapy, photothermal therapy, gas therapy, genetic therapy, and immunotherapy. We highlight how nanomaterials can be utilized to amplify antitumor radiation responses and describe cooperative enhancement interactions among these synergistic therapies. Moreover, the potential challenges and future prospects of radio-based nanomedicine to maximize their synergistic efficiency for cancer treatment are identified.

     

埋地管道在冻土带的热力变形分析

埋地油气管道通过永冻土地带时,由于管内介质与周围的冻土发生了热力作用,使冰土解冻,在管道周围形成融化圈。文章分析了永冻土的特点,建立了永冻土地带土壤传热数学模型:融化圈内外传热方程、管道向土壤和土壤表面向大气所放热量的守恒关系、融化圈界面处土壤温度、相变界面处固相变为液相的传热条件。还建立了埋地管道模型,并以穿过永冻土地带土壤的输油管道为例,分析并计算了各种应力的最大值所在的位置和大小,提出了在永冻土地带减小管道热力变形的措施。     

Fenton试剂降低采油污水CODCr的研究与应用

针对辽河油区超稠油采油污水的特点，采用Fenton试剂催化氧化，对采油污水处理进行研究。实验研究及现场应用结果表明，此方法对污水的CODCr具有良好的去除效果。处理后污水经过简单生化，进一步降解污染物，能够实现稳定迭标排放，且具有能耗低、运行成本低和操作简单等特点。     

气动贯通式潜孔锤反循环连续取心取样钻进新技术在河南钼矿中应用

三道庄钼矿勘探生产中钻遇的地层非常复杂，采用其他方法均无法实现钻进，经过分析比较，决定采用贯通式潜孔锤反循环连续取心（样）钻进新技术来解决该地层钻进难、成孔难、取样难等三大问题。文章从钻进技术特点、工作原理等方面对该技术进行详细分析，得出其具有钻进效率高、岩心（样）采取率高、成孔质量好等突出优点。并介绍了钻进主要设备机具的配套、施工工序、操作要点、遇到问题的解决方法等。在河南钼矿露天采石场应用该项技术，有效避免了塌孔和卡钻事故，工程进展顺利、质量好、岩心（样）采取率在98％以上，取得了良好的效果。针对在生产试验中遇到的某些问题，作者提出了一些改进建议。     

Studies on high density polyethylene (HDPE) functionalized by ultraviolet irradiation and its application

The structure and properties of high density polyethylene (HDPE) functionalized by ultraviolet irradiation at different light intensities in air were studied by electron analysis, FTIR spectroscopy, contact angle with water, differential scanning calorimetry and mechanical properties measurement. The results show that oxygen‐containing groups such as C?O, C—O and C(?O)O were introduced onto the molecular chain of HDPE following irradiation, and the rate and efficiency of HDPE functionalization increased with enhancement of irradiation intensity. After irradiation, the melting temperature, contact angle with water and notched impact strength of HDPE decreased, the degree of crystallinity increased, and their variation amplitude increased with irradiation intensity. Compared with HDPE, the yield strength of HDPE irradiated at lower light intensity (32 W m^?2 and 45 W m^?2) increases monotonically with irradiation time, and the yield strength of HDPE irradiated at higher light intensity (78 W m^?2) increases up to 48 h and then decreased with further increase in irradiation time. The irradiated HDPE behaved as a compatibilizer in HDPE/polycarbonate (PC) blends, and the interface bonding between HDPE and PC was ameliorated. After adding 20 wt% HDPE irradiated at 78 W m^?2 irradiation intensity for 24 h to HDPE/PC blends, the tensile yield strength and notched Izod impact strength of the blend were increased from 26.3 MPa and 51 J m^?1 to 30.2 MPa and 158 J m^?1, respectively. Copyright © 2003 Society of Chemical Industry     

Supermedia-enhanced Internet-based telerobotics

This paper introduces new planning and control methods for supermedia-enhanced real-time telerobotic operations via the Internet. Supermedia is the collection of video, audio, haptic information, temperature, and other sensory feedback. However, when the communication medium used, such as the Internet, introduces random communication time delay, several challenges and difficulties arise. Most importantly, random communication delay causes instability, loss of transparency, and desynchronization in real-time closed-loop telerobotic systems. Due to the complexity and diversity of such systems, the first challenge is to develop a general and efficient modeling and analysis tool. This paper proposes the use of Petri net modeling to capture the concurrency and complexity of Internet-based teleoperation. Combined with the event-based planning and control method, it also provides an efficient analysis and design tool to study the stability, transparency, and synchronization of such systems. In addition, the concepts of event transparency and event synchronization are introduced and analyzed. This modeling and control method has been applied to the design of several supermedia-enhanced Internet-based telerobotic systems, including the bilateral control of mobile robots and mobile manipulators. These systems have been experimentally implemented in three sites test bed consisting of robotic laboratories in the USA, Hong Kong, and Japan. The experimental results have verified the theoretical development and further demonstrated the stability, event transparency, and event synchronization of the systems.     

一种基于混沌同步的噪音衰减算法

论文提出了一种混沌通信系统的噪音衰减算法,该算法利用混沌同步现象在接收端获得正确的噪音估计值,从而从接收信号中滤除噪音恢复出正确的信号。通过数值仿真试验表明该方法是可行的。     

真空铸造高强度C/Mg复合材料

本文介绍用真空铸造法制造抗拉强度超过1000MPa的高强度C/Mg复合材料。将T300纤维经C-Si-O梯度涂层处理后单向排布于型腔内,在真空下注入ZM-5合金液,凝固后即得C/Mg复合材料零件或试样。试样的抗拉强度在纤维体积分数为0.35时达1050MPa。本文讨论C-Si-O梯度涂层对获得高强度复合材料的作用。     

地面油管漏失定量测试方法探讨

对油管漏失进行定量测试的方法确定具体漏失位置。方法运用双频道回声探仪探测动液面的原理和工作方法，根据油管漏失形成的死油坏在测试曲线上出现特殊波位置判断油管漏失位置。结果：经过７０多井次的现场试验，该方法具有较高的准确性和可靠性。结论：利用特殊波可以有效监测油管漏失，并具有推广使用价值。     

冶金过程中复杂夹杂物和钢液化学平衡计算

本文提出一个同温冶炼过程中预测非金属夹杂物沉淀的计算机程序。本研究中，多元硅酸盐溶体的Ｇｉｂｂｓ自由能由基于统计热力学的晶胞模型来计算，该晶胞模型按照氧与周围的阳离子构成的对称和非对称晶胞来描述硅酸盐熔体结构，假定高温冶炼时认与非金属夹杂物平衡，钢液中氧化物元素的活度由Ｗａｇｎｅｒ交互作用系数来计算，利用本程序可以估计炼钢时沉淀的非金属氧化物的成分，为调整冶炼工艺和提高产品质量提供指导，进一步可计